Serving sailors online since 1997
 
 

Recent Topics

Claude L.-Auger at 12:01am 12.15.02
1/715
Because Sacripant has been on the hard since mid-October, happy times ' get-togethers are few and fa
Sam at 11:24pm 12.14.02
0/800
After replacing my Yanmar 9hp last summer we found that the new one turns clockwise. Since the old o
john dawson at 11:48am 12.14.02
0/603
I once took a date on an overnight sail in the lower Potomac starting at an obscure boat ramp in sou
Jan LaFrance at 11:38am 12.14.02
1/1389
I recently purchased a Hunter 25.5 and the winch needs repair. It is a Maxwell 17 and the springs n
Ken Shur at 9:34am 12.14.02
1/1025
Does anyone make a engine davit/lift (4 hp) that can be attached to the arch without drilling more h
Tom at 9:16am 12.14.02
0/1012
its on right now (8PM est). saturday Looks very interesting !...with live scenes of CG boats runni
steve c at 8:23am 12.14.02
1/824
i was taking all the fome floation out of my boat and saw some damage at the forward part of my keel
Sean Herron - herrons@telus.net at 6:51am 12.14.02
2/966
Hello, Perhaps I had a little to much whisky in celebration, or whatever, no need to justify drinki
Mark Sanford at 6:28am 12.14.02
3/1246
Are the "Reference Articles" by Peggy Hall still available? I cannot seem to find them.
Larry Galuski at 5:53am 12.14.02
2/849
I would like to get a new Jib or Genny....Can anyone offer any advice. Thanks
Steve at 4:13am 12.14.02
10/1158
I live in a cold winter climate. How important is it or any comments on whether to cover my boat for
Vicki Berryhill at 1:15am 12.14.02
8/1707
I recently bought a 1984 Catalina 30. It has a 25 HP Diesel. I was doing some maintenance to the en
Richard at 11:35pm 12.13.02
1/3484
Hi, I am interested in purchasing the Sealand 911-M28 toilet, which requires pressurized water - w
glen at 11:11pm 12.13.02
2/1174
Have a side stay (shroud?) that is unraveling and needs to be replaced. Should I replace all on both
Scott at 9:57pm 12.13.02
1/736
We all saw the posts about the loops on new UK furling main sails needing to be reenforced, but it w
Ernie Tetrault at 9:21pm 12.13.02
5/3504
Alright gang, get ready for a real head scratcher. For several months now I've been finding diesel
Captain John Edwards at 8:15pm 12.13.02
46/2944
Well we finally did it. My wife and just accomplished a rebedding project on our boat. We had tried
Tony Kriz at 1:35pm 12.13.02
0/670
Well, I just completed the purchase of my new boat - '83 Hunter 25! Can't wait to get out and do so
William at 10:45am 12.13.02
2/815
I just acquired a used 1988 Catalina 22. I would like to replace the tiller and some of the rigging.
Sean Herron at 9:43am 12.13.02
0/959
Hello, This link is not an ad, but a very nice bit of downloadable to be local code, that searches

Recent Replies

Masthead rig   (1)
DrJudyB at 2:30pm 05.03.20
Masthead rig
DArcy at 2:24pm 05.03.20
I hear you on tacking a big genoa. I used to single hand my C&C 27 a lot and would only hoist the 16
Escape plastic is cracking
capta at 2:09pm 05.03.20
Could a hot glue gun do the trick?
Looking for Hunter 340 owner help
sailcapt340 at 2:05pm 05.03.20
Since the boat is out of the water right now...........and your in grease mode......... Your seacock
Bow thruster - is it a plus or minus?
jssailem at 2:04pm 05.03.20
******************.*******. Never thought labeling people in this way was a positive way to go.
Bow thruster - is it a plus or minus?
Noodat Lady at 1:53pm 05.03.20
I would pay extra for a boat with a bow thruster. And a bit more if there were a stern thruster too.
Escape plastic is cracking
Hunter216 at 1:36pm 05.03.20
I have an 11.5ft Escape Mambo, one piece plastic hull.... it has cracked where the Keel slides into
high water?
jon hansen at 1:35pm 05.03.20
we are forecast for no rain for the next ten days. yippee
Masthead rig   (3)
Drinky Crow at 1:31pm 05.03.20
So there's some confusion w/vernacular here... uilding a "fathead" as above w/max roach to clear bac
Escape plastic is cracking
Dave Groshong at 1:30pm 05.03.20
The material is ACP, cracks are usually superficial, but even using the correct repair material,
Escape plastic is cracking
dlochner at 1:29pm 05.03.20
The Mambo is rotomolded polyethylene. Some plastic shops may be able to weld it. https://www.cheyn
CQR 35 pound anchor on a B331 anchor roller?
jssailem at 1:26pm 05.03.20
It is all about proper setting and scope. The 13 was a small anchor on a speed boat. He was definite
Yep
shemandr at 1:23pm 05.03.20
Darwin candidate. Not top tier but an honorable mention.
CQR 35 pound anchor on a B331 anchor roller?
Bluenose at 1:17pm 05.03.20
To BigEasy: Yes, that's what I have and it has never given a problem. Must be the standard set-up th
Escape plastic is cracking
ggrizzard at 1:06pm 05.03.20
FWIW: Don't know the boat or it's composition, but some plastics can be "Welded". A local auto bod
Yep
kappykaplan at 1:02pm 05.03.20
That's sick, but funny!!!:beer:
HIN Location
Richard19068 at 1:00pm 05.03.20
Too much time on my hands. This is a stretch. If you change the I before the F to a 1 that makes a
STUCK TRANSMISSION FILL PLUG
Benny17441 at 12:57pm 05.03.20
Apply BP Blaster and let it soak overnight, lightly but firmly tap it on top repeatedly with a hamme
high water?   (1)
Hunter216 at 12:44pm 05.03.20
Back up to 9,760 :)
HIN Location
Hunter216 at 12:41pm 05.03.20
IRC3400IF909 That is not a Hunter HIN as it would begin with HUN IRC is Indian River Custom Yacht

Copyright 1997-2024 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.