tom
at 2:53pm 12.02.02
8/1740
just bought the boat and noticed a few things that i have questions on..this post is only one of a
|
||
Bob
at 1:38pm 12.02.02
4/731
Several years ago I became well acquainted with hundreds of blisters on my previous boat (18' Renken
|
||
Dennis
at 1:29pm 12.02.02
5/960
After installing my ICOM 710-RT with a Morad whip off the stern I am wondering if anyone else is hav
|
||
Wally Scheid
at 12:50pm 12.02.02
8/3732
I would like to know where to get a replacement impeller fo my 11 HP diesel water pump. I have a Blu
|
||
Bob Lufkin
at 12:39pm 12.02.02
24/2491
Cape Cod - Sen. Edward Kennedy's schooner, The Mya, was freed from sand and shallow water off Cold S
|
||
Mike
at 12:17pm 12.02.02
5/956
My OMC Zephyr is acting up and I was thinking of a re-power for my 25'Oday. I was thinking of using
|
||
howard
at 11:44am 12.02.02
4/744
While looking thru the archives for help on another matter, I found posts saying that switching to a
|
||
Gary A.
at 11:09am 12.02.02
6/1598
I need to know the measurements of the companionway boards for a Hunter 34. I have a 1983 model that
|
||
Bill P.
at 11:05am 12.02.02
2/1108
I don't have a drawing that shows whether in fact the bottom of the rudder or the winged keel is the
|
||
David Smith
at 10:50am 12.02.02
4/1048
I have moved my boat to the Mississippi and my marina does not have a boat hoist. I purchased my C2
|
||
Jim
at 10:29am 12.02.02
3/879
I'm planning on painting my boot stripe next spring with a one part polyurethane paint. What would b
|
||
Steve de Filippis
at 10:01am 12.02.02
5/773
does anyone know of any problem areas on this model?
|
||
arthur Reynolds
at 9:09am 12.02.02
3/817
tiny leak from fuel tank . All hose clamps ok and yard wants to pull the tank. If I knew it would ge
|
||
john withrow
at 8:36am 12.02.02
3/826
Pulling my 26 out the rudder lost about an 1/2"on the bottom. Is this going to create enough of a co
|
||
Larry McKay
at 8:06am 12.02.02
6/942
My 340 is 2 years old and the wooden companionway steps could use some workto make them look new a
|
||
Lewis
at 7:43am 12.02.02
6/1034
1993 Hunter 28 - When engine is running I notice a small drip around the fuel pump. The drip seems t
|
||
george kornreich
at 7:30am 12.02.02
15/1376
Where have your reference articles been moved to? Can't find them now.
|
||
John Visser
at 7:26am 12.02.02
6/1304
Anyyone have Nexus sailing instruments (Brunton/Silvea), or know much about them? i'm interested, b
|
||
Roger Rollins
at 7:13am 12.02.02
9/1029
I've recently bought a '79 H33. There's a small round plastic port in the inboard wall of the head
|
||
John Visser
at 7:11am 12.02.02
5/837
Phil,Where's my post entitled "C36 technical drawings" in the big boats forum? Seems to have disa
|
MarkSetBot -Automatic race marks
PaulK at 8:40pm 05.01.20 $6000 ? There are probably lots of kids who would be happy to anchor wherever you told them all sum |
||
STUCK TRANSMISSION FILL PLUG
TimFromLI at 8:25pm 05.01.20 I second the vice grips or use a dremel to grind the sides to fit a smaller box wrench. |
||
Will Gilmore at 8:11pm 05.01.20 close it up; and get a GPS. It gives you speed over the ground If you want speed through the water |
||
1985 hunter 31 stern leak (1)
jssailem at 8:03pm 05.01.20 @LeslieTroyer recently repaired damage to his rudder. When we explored the damage, we discovered a c |
||
Anchor Roller
jssailem at 7:44pm 05.01.20 25Kg is 55 Lbs... Likely larger than needed for the sized boat. |
||
Tohatsu outboards
JRT at 7:31pm 05.01.20 I had 2 6hp, a short shaft for my fishing boat and then an ultra long shaft for my O'Day 25. Great |
||
Insurance question
Dalliance at 7:28pm 05.01.20 Even with agreed hull value I think they still get you for depreciation unless your boat is totaled |
||
First 405 interior wood.
BigEasy at 7:15pm 05.01.20 Beneteau was using Duka wood at one time; not sure about the wood on your specific boat. |
||
Hunter 31 Jib Car
kloudie1 at 7:11pm 05.01.20 Probably needs to be a solid pin to carry the loads. Should be 316 stainless steel . Talk to a machi |
||
Replacing detaching interior vinyl with wood slats
guidera48 at 6:57pm 05.01.20 I had the same problem. i found the best way to remove that nasty foam (turned to dust) backed vinyl |
||
Tohatsu outboards
rgranger at 6:51pm 05.01.20 I have the 6 sail pro long shaft I LOVE IT. It always starts on the first pull this spring I hook |
||
1985 hunter 31 stern leak
ggrizzard at 6:47pm 05.01.20 Well, I'll play twenty questions... Is the "exhaust thru hull" near the wet area? Does the wet wood |
||
Sailing with a High
BigEasy at 6:46pm 05.01.20 Went for a short sail this afternoon. Winds were on the light side, just the way the admiral likes i |