|
Dave
at 3:53am 05.13.03
0/850
Can anyone recommend a captain to deliver a 30-footer from Manitowoc to Waukegan?
|
||
|
w hallett
at 3:41am 05.13.03
2/1728
do you know where i can find one of these for an older oday 14 plus the hardware?
|
||
|
Mark
at 3:34am 05.13.03
2/1568
Hello.I am thinking of purchasing an O'Day 28, and would like to know procedure to "tune the rig";
|
||
|
Peter Hoenderop
at 2:47am 05.13.03
0/870
I am owning a Hunter 310 build in 1997 with a yanmar engine. The propellor shaft is 25 mm. Can anybo
|
||
|
Carl Lebo
at 2:19am 05.13.03
1/936
I've been kicking around the idea of adding an anchor locker. Is there a kit that would help or woul
|
||
|
Floyd
at 1:27am 05.13.03
1/909
We are about to launch a new Hunter 386 with a PYI three blade prop and want to be sure on the corre
|
||
|
Gary
at 12:20am 05.13.03
3/1104
I have a Catalina 30 on which there is a small electrical connector (fitting) just below the engine
|
||
|
Tim
at 11:02pm 05.12.03
4/1057
Does anyone here have any experience with the gelcoat repair kits that marine stores sell? Do they
|
||
|
John Fisher
at 10:30pm 05.12.03
2/1020
WE HAVE A FEW HAIRLINE CRACKS IN THE NON-SKID SURFACE AREAS OF OUR 86 272 .WE HAVE FILLED THE CRACKS
|
||
|
Stuart
at 9:13pm 05.12.03
10/1028
Have a 1999 Hunter 340. We've had two instances of issues with our Yanmar.First occured while m
|
||
|
JimR
at 9:02pm 05.12.03
1/996
Trying to find the replacement No. of the Internal halyard sheaves P'S located at the bottom of the
|
||
|
Ray Dobmeier
at 8:59pm 05.12.03
6/1496
We just launched and rigged our 1994 26S Mac. Nowhere in the manual does it even mention the boom t
|
||
|
Linda
at 8:09pm 05.12.03
2/1153
I've checked through the archives and haven't found this answer. I hope someone here can help.I r
|
||
|
Herb Schiessl
at 2:39pm 05.12.03
5/1140
I am repairing my delaminated rudder, but I was wonderinng where a rudder usually breaks. Is it at t
|
||
|
Bob Fliegel
at 1:31pm 05.12.03
7/893
I was thinking of relocating my two batteries from the starbord, aft section of the boat (next to th
|
||
|
mmsailor
at 1:25pm 05.12.03
6/1918
I can not find my owners manual for my 1999 0r 2000 nissan 5 hp 2 stroke outboard, I had someone tun
|
||
|
Bob Fliegel
at 12:42pm 05.12.03
11/913
Hi Everyone! I have been finishing up numerous winter projects prior to putting the boat back in the
|
||
|
Warren
at 12:23pm 05.12.03
2/972
On my recently purchased Cat 30 I have to replace the batteries, not so much due to a failure but du
|
||
|
Warren
at 12:10pm 05.12.03
1/861
I recently purchased a 1989 Cat 30 with Adler/Barbour refrigeration not working. According to the PO
|
||
|
anthony
at 12:07pm 05.12.03
2/1156
Ihave a 1977 24 Venture MacGrego sail boat. The cabin has a pop up, can you sail with the pop up? Th
|
|
O'Day 20 Spreader Bracket Mast Holes
shemandr at 4:47pm 10.04.20 Thanks. I should have guessed that is the technique. |
||
|
New sailer
Glsawyer at 4:34pm 10.04.20 Is there away to delete this tread? I'd like to not clutter the forum |
||
|
Engine failing to start, help with Diagnosis
sailme88 at 4:25pm 10.04.20 My ignition recently gave up the ghost.. The fact that the panel illumination failed would indicate |
||
|
Cockpit Cushions
Ron20324 at 4:24pm 10.04.20 Can I borrow your wife? Twenty dollars- same as downtown. ;) |
||
|
Engine failing to start, help with Diagnosis
garymalmgren at 4:23pm 10.04.20 Do you have a wiring diagram? Is so refer to it or post on here so we can follow it. The instrument |
||
|
Engine failing to start, help with Diagnosis
leo310 at 4:16pm 10.04.20 check the ground wire to the engine |
||
|
Looking for photos of V-berth port and starboard removable shelves - O-Day 28
Richard19068 at 4:15pm 10.04.20 Sorry Fred. I misunderstood. For some reason I thought you were talking about shelves in the V-Berth |
||
|
O'Day 20 Spreader Bracket Mast Holes
Timm R Oday25 at 4:09pm 10.04.20 The compression tube can be inserted through either the top or the bottom of the mast . We used a 20 |
||
|
What to do if you lose your rig.
Daveinet at 3:57pm 10.04.20 Yes, Mills race. It very hard to cut the rigging when the boat is violently rolling and pitching. W |
||
|
Windlass Seized Clutch
shemandr at 3:45pm 10.04.20 ...Windlass would have to come out to be able to get hammer swing room.. Maybe it's not appropriate |
||
|
Windlass Seized Clutch
Terry Cox at 3:29pm 10.04.20 Tried to remove the set screw last week. No luck yet. Not enough room for my impact wrench. Need a l |
||
|
Onan Cummins 8KW Genset Issue
Terry Cox at 3:23pm 10.04.20 Thanks all for your helpful tips and recommendations. A very good feeling when solving problems such |
||
|
Engine failing to start, help with Diagnosis
rgranger at 3:21pm 10.04.20 Not sure what engine you have but many have an inline fuse near the starter. It is not the fuse if |
||
|
Engine failing to start, help with Diagnosis
rgranger at 3:18pm 10.04.20 Obviously an electrical issue - two options - You left one out....:thumbup::biggrin: |
||
|
Cockpit Cushions
smokey73 at 2:46pm 10.04.20 Yep- ex- 9 years now Oops, didn't catch the then. Nevermind I already have a then wife but she co |
||
|
Would You Use Biodiesel if Available
shemandr at 2:39pm 10.04.20 I wonder what burning biodiesel would do to a typical engine warranty? I'd expect the manufacturer |