Scott Blahnik
at 4:04am 04.08.03
1/867
I'm not sure what brand it is,it came with my 2001 270. The readout looks like this: --- (three das
|
||
lloyd
at 3:49am 04.08.03
1/971
Hello,I would just as soon NOT drill holes and use screws to attach my mast head light,but is this
|
||
Richard Gresham
at 3:30am 04.08.03
1/942
Does anyone have the dimensions for the attachment points on the boom for a C30?
|
||
Dan
at 3:26am 04.08.03
0/835
My old C22 had some really loose rigging and no more room for tightening, so I ordered the shroud an
|
||
Mike
at 2:58am 04.08.03
7/1011
Can anyone shed light on the problem we are having with our 2GM15? We have a '79 h33 with this Yanm
|
||
Paul H
at 2:44am 04.08.03
11/697
Dave, to further complicate this. I've already run a bead of silicone along the whole length of the
|
||
Todd
at 2:24am 04.08.03
1/1365
I have a Hunter 265 that I am considering moving to Lake Norman, NC. Can someone recommend a marina
|
||
Brad
at 2:06am 04.08.03
1/835
The groundwire from my mast is wrapped around the forward keelbolt under the nut. The exposed wire i
|
||
Joe Mullee
at 12:17am 04.08.03
9/1857
I'm reading a book about preparing a boat for cruising. In the chapter on engines it goes over emerg
|
||
Bill Paul
at 11:47pm 04.07.03
1/1032
Hello, everyone! Oh, boy, are we excited! We just bought a 1981 O'Day 37cc. She surveyed very wel
|
||
Don Evans
at 10:27pm 04.07.03
1/1131
I saw an interesting new product recently at the Cottage Life Show in Toronto, and was wondering if
|
||
Wayne
at 10:20pm 04.07.03
2/1197
The gooseneck has just worn out on my boat. The part that is at the end of the boom will no longer
|
||
Last Place Lou
at 9:31pm 04.07.03
4/1281
The sailing club group with which I race are not hard core, mostly learning how to sail their boats
|
||
Last Place Lou
at 9:29pm 04.07.03
15/1745
The sailing club group with which I race are not hard core, mostly learning how to sail their boats
|
||
Dave Laing s/v Windsong
at 8:27pm 04.07.03
6/1067
I did a dumb thing and let my Lexan sliding hatch slam down. Now I need to repair where a small corn
|
||
Mark Green
at 11:52am 04.04.03
0/804
I will be keeping my 2002 Hunter 170 on a mooring ball in a freshwater lake in Missouri. Is it reco
|
||
Rob
at 11:08am 04.04.03
5/917
Why is it that in anything over 15 Knots my O'DAY 25, with a fin keel, constantly buries the windows
|
||
Gary
at 8:25am 04.04.03
0/817
New owner of 76 O'Day 25I posted a message the other day regarding the lack of a chain locker and g
|
||
Michael Fisher
at 7:49am 04.04.03
3/830
I am having problems with the forward holding tank/macerator(again). The macerator pump does not see
|
||
Scott Pittam
at 7:11am 04.04.03
2/799
Could somebody help me out on the batten sizes for a '94 H26. I purchased it last season and the pre
|
How many H23s were built?
kgibson4 at 6:37pm 05.18.20 Ok Dave, I did not realize you needed the entire registration #. It is: HUNA1228E787. The original |
||
Raw water intake thru hull relocation Yamaha 25
seatane at 6:34pm 05.18.20 @AJW I believe using brass fittings you find at Home Depot below the waterline would be a big mistak |
||
An Actually portable Air Conditioner?
Captain Larry-DH at 6:33pm 05.18.20 There are a few tests of these units on Youtube, they seem to work for small spaces. This guy ran i |
||
Alternator re-assembly
Scott T-Bird at 6:28pm 05.18.20 I'm just wondering if the "thick washer" on the "Alternator pivot stud" is on the right side of the |
||
Sail Trim and Aeronautic Theories.
Ken Cross at 6:25pm 05.18.20 Well there you go - science prevailing again ! :) Curious about what you changed in your approach |
||
Beleated Hello - Y25 Owner
seatane at 6:18pm 05.18.20 Hey Drew, thanks for sharing your families story of adventure in a yamaha 25. Most impressive and |
||
79 Hunter 27 Spedometer wheel
twalker H260 at 6:11pm 05.18.20 You might try these folks. See if this is the same transducer. https://store.srinstruments.com/2-w |
||
An Actually portable Air Conditioner?
DArcy at 6:05pm 05.18.20 There are a few tests of these units on Youtube, they seem to work for small spaces. This guy ran it |
||
Polyurethan Stripper?
envisionvenicefl at 5:59pm 05.18.20 Good question. I have a similar project ahead of me on a recently acquired Oday 28. |
||
Trouble with jib roller furling on Hunter 170 (2-part question) (1)
Hunter216 at 5:54pm 05.18.20 Part One: I am having trouble furling the jib on my Hunter 170 using roller furling and am looking |
||
Alternator re-assembly
DArcy at 5:51pm 05.18.20 I'm just wondering if the "thick washer" on the "Alternator pivot stud" is on the right side of the |
||
high water?
jon hansen at 5:46pm 05.18.20 prolly so. those artesians are know to cause trouble still coming down like cats and dogs here |
||
Winch help
Davidasailor26 at 5:44pm 05.18.20 Not sure if you have a set up on your sail like mine: see picture. If so, you might have made the m |
||
Sailing into a marina
DArcy at 5:43pm 05.18.20 People sail into our harbour sometimes, I've done it a few times, I've even seen spinnakers in the h |
||
Center board line tension
Will Gilmore at 5:35pm 05.18.20 My question now is. Are there different centerboards for the these boats as options or aftermarket. |
||
Nasty Stuff inside my boat.
Project_Mayhem at 5:28pm 05.18.20 @thinwater Is there any chance that @corbinstein 's combination of CLR and bleach could cause a harm |
||
Clean up on aisle 5: how to clean up old cleats
jaysweet at 5:08pm 05.18.20 I was just joking about the wiring... but some people get really twisted up about connectors. It's |