Tim
at 9:07pm 03.28.03
4/2021
Does anyone know of a source for marine standards? In particular, I'm seking information on what typ
|
||
tom b cat22
at 8:35pm 03.28.03
2/884
when is it?? or did i miss it??
|
||
Richard Wagner
at 1:11pm 03.28.03
3/983
I had to pull the centerboard because of binding. The centerboard looks =OK, but the pin shows wear
|
||
Bill Graham
at 1:09pm 03.28.03
2/963
After reading about the Mac 26X in heavy seas it has peaked my interest in wonderingif the 26D and
|
||
Richard McDonald
at 12:43pm 03.28.03
7/5979
I need to replace all of the gaskets on every hatch and portlight of my 1979 H37C. I know that I can
|
||
Jerry
at 12:42pm 03.28.03
6/1032
I hear that replacing the rub rail is a real....well, let's say, "A difficult job." That's polite.
|
||
Ray Juarez
at 11:48am 03.28.03
5/1233
I have two questions the first the winches on my 25.5 (1984) don't catch and have been slipping. Whe
|
||
denis
at 11:32am 03.28.03
2/835
is there a mast light on the 1989 18.5 model.? there is a wire an as i have ni manual i do not have
|
||
Robert
at 10:47am 03.28.03
2/948
need to know if a boat maker by the name "Pena" ever existed, if so is there anywhere on the web i c
|
||
Chris
at 9:55am 03.28.03
9/1242
I have to replace my mainsail for my O'Day 30........I've looked in magazines and upon close exaimin
|
||
Mike Daus
at 9:34am 03.28.03
3/3978
Our old (+20 yrs) Eberspacher D3L cabin heater (3200 W heat output) recently failed and needs replac
|
||
Nate
at 9:20am 03.28.03
1/1005
I'm looking for the specs on the spreaders found on the Widgeon. ie. length, outside diameter, wall
|
||
Ken Kahn
at 7:54am 03.28.03
0/898
Has anyone installed a dual output alternator and jumped the two outputs and used it as a single out
|
||
Russell Egge
at 7:21am 03.28.03
7/1372
Went to look at the tank configuration and measure the hoses for replacement. I know we are suposed
|
||
David Mosley
at 5:07am 03.28.03
2/867
I have an '85 Hunter 23 and love the performance changes with the daggerboard down upwind, and raise
|
||
Richard Planas
at 5:04am 03.28.03
6/1397
Peggy, once again, thanks for your reply to my e-mail. Searching through the forum I ran into someon
|
||
Alan
at 4:53am 03.28.03
0/824
What size cutless bearing do I need to buy to replace on my 1978 O'Day 27?Boat has a Yanmar YSB8
|
||
Winnie N.
at 4:40am 03.28.03
8/2421
What is the proper position for the slings when hauling or launching a 34' Hunter, vintage 1986? I
|
||
Les Murray
at 3:39am 03.28.03
1/935
List Mates,My C-36 has just a single bow cleat. I want to add two more adjacent to the anchor loc
|
||
Kevin Muhlendorf
at 2:40am 03.28.03
1/963
On the starboard side of the rudder, there is a rust trail that goes down a good foot and a half - t
|
2008 Hunter 33 Anode Replacement
jaysweet at 6:02pm 05.17.20 Yes, I do mean the zinc anode to clamp to my prop shaft. I tried a 1 inch and it was a tad too sma |
||
Yanmar 2GM20F: please criticize my plan!
BigEasy at 5:52pm 05.17.20 Go for it! Looks like a good plan. All of the remaining engine work can be done in your slip. |
||
PVC Tube in 340 Mast
jssailem at 5:51pm 05.17.20 Do you have a "Topping Lift and a Jib halyard? You do not want to trust the Main Halyard to get to |
||
F*!$#ing Scupper hoses
ontherocks83 at 5:36pm 05.17.20 The bruises and cuts on your forearms from that job are no joke, I was telling someone that after I |
||
F*!$#ing Scupper hoses
doublebuffle at 5:30pm 05.17.20 My transom looks about the same. I just pulled the exhaust hose out to replace the through-hull with |
||
Fixed Portlight replacement on Passage 42
eianm at 5:25pm 05.17.20 i just removed one yesterday to re seal it and they are a lot more than a piece of cut perspex! Ther |
||
2008 Hunter 33 Anode Replacement
amitchell64 at 5:22pm 05.17.20 Sorry: do you mean what size of zinc to clamp to your prop shaft? (Or do you mean a protective anod |
||
Clean up on aisle 5: how to clean up old cleats
jaysweet at 5:17pm 05.17.20 "I'm not a smart man": Forest Gump. But if I were, I would have learned by now that you never post |
||
Diesel fuel leak
Hydro Therapy at 5:14pm 05.17.20 My Westerbeke was leaking fuel around the area of the tranny. The lift pump was the culprit. Rust cr |
||
Perko raw water filter
justsomeguy at 5:08pm 05.17.20 Have you tried a bit of oil/penetrant, tapping the joint, another drop of oil and then time? |
||
merc 9.9 outboard on my 260- help please
gudiss at 5:05pm 05.17.20 andy, thank you very much!! that should do it- |
||
R20 Outboard length? (2)
AndyVS at 4:38pm 05.17.20 Here are a couple of pics of my 9.9 on my Mac26C. I slip on a small inland lake and rarely lower the |
||
Stuck throttle? (15hp Chrysler/Johnson)
sbcwolff at 4:35pm 05.17.20 Going to try and clean carb and start again... maybe when it is running and not quitting we can put |
||
Small cracks in Hunter 28.5 fresh water tank
Hello Below at 4:23pm 05.17.20 Mike, I have only general information for you that I found. You can put epoxy on gelcoat (polyester |
||
Clean up on aisle 5: how to clean up old cleats
thinwater at 4:00pm 05.17.20 Oh no. You really should not have shown us the snap-lock.... A whole new thread on crimp vs. solder |