bill van
at 3:29am 10.11.04
5/749
Being a new sailer (and very inexperienced) can you tell me if what I'm doing is correct. Yesterday
|
||
David Babcock
at 3:19am 10.11.04
4/1194
I purchased a home built sailboat to restore. The major issue is what to do with the hole in the gla
|
||
Gregg
at 3:12am 10.11.04
1/1426
Hi Peggie - Just bought Raritan's CP for the bowl. The label talks about chemical head products an
|
||
jmcclain
at 3:10am 10.11.04
2/814
There seems to be no end to the "wax, polish, cleaner" controversy on this and other boating sites.
|
||
George H260
at 2:54am 10.11.04
3/931
Hi AllI just did a archive search and could not find the answer I need, so here it goes.I have a
|
||
Brad18489
at 2:49am 10.11.04
4/1291
Hi: I have a freshwater Beneteau 400 with a maze of fine spider (stress)cracks all over the hull be
|
||
Brad18489
at 2:44am 10.11.04
0/1139
Hi: I have a freshwater Beneteau 400 with a maze of fine spider (stress)cracks all over the hull be
|
||
rforsyth
at 2:43am 10.11.04
2/892
Four years after my '96 Catalina 42 MK II was placed in fresh water, I had it taken out of the water
|
||
Tony Litvak
at 2:39am 10.11.04
10/11413
I just purchased a C'C 24 (1983) and would like to find out the mast height from the waterline to se
|
||
David Hoch
at 2:39am 10.11.04
1/774
Bruce,What is the best way to ensure that epoxy bonds to the existing GRP when adding new structur
|
||
fretz
at 2:28am 10.11.04
1/1159
My 1976 mariner is seperating at the hull to deck joint. there is a horizontal flange on the hull
|
||
Cal23337
at 2:12am 10.11.04
2/1158
Has anyone installed an electric windlass on a Hunter Vision 36 that would like to share installatio
|
||
artururo devitalis
at 2:11am 10.11.04
1/1039
Have received different answers to the question regarding the manufactures specs on shaft length. My
|
||
jim hartman
at 2:02am 10.11.04
1/810
There is a 3inch crack or line in the fiberglass. It looks like a black line, right where the cockpi
|
||
John W
at 1:52am 10.11.04
3/989
I am stumped as to why my raw water pump is not pumping water. I just replaced the impeller, the ot
|
||
John Richard
at 1:44am 10.11.04
4/3469
Our boat is 3.5 years old. The dodger and side windows have always been covered with Sunbrella. Th
|
||
Jason
at 1:41am 10.11.04
1/1179
I'm looking to make replacement hatch boards for a 2002 331. Does anyone know where I can get the di
|
||
Jim S.1435
at 1:33am 10.11.04
1/1366
I have 95' C30 MKlll which appears to have a leak coming from the strut bolts under the hot water he
|
||
sailexa
at 1:22am 10.11.04
1/1156
What's the preferred finish for a teak shower grate. Our's is presently unfinished teak, and I'm th
|
||
Rob
at 11:57pm 10.10.04
6/1099
I have a 1964 5 1/2 HP Jhonson outboat that has treated me well for 3 years. Last year I had the hos
|
Summer in the Salish Sea
SoSound at 8:56pm 08.16.20 @Michael Davis, you keep posting pictures. I'll keep entering new waypoints and destinations. :thu |
||
Cruising RPM research
JohnShannon at 8:06pm 08.16.20 The generator should always run at constant RPM. Load is still a relevant concern. If the electric |
||
LITTLE TO NO WIND
Hayden Watson at 7:58pm 08.16.20 Thanks for the timely thread! :beer: This was fresh in my mind when I took the family out yesterday |
||
Pre-purchase survey checklist
Ken Cross at 7:49pm 08.16.20 Here in the Northwest, wet cores is a huge deal. You also need dry weather to test for a wet core (a |
||
New 37C owner
dLj at 7:19pm 08.16.20 I'm sure you will get some insight from @Tugslife or other knowledgeable forum members here but @M |
||
Pop Top Gas Spring Addition
Gene Neill at 7:15pm 08.16.20 Only gravity was holding the pop-top down. Dammit man! LOL ... And no previous owner could be bo |
||
Smoke detectors and Carbon Monoxide detectors
Ralph Johnstone at 6:44pm 08.16.20 The engine compartment will melt them so best located in the cabin area, out in the open, about 60" |
||
Smoke detectors and Carbon Monoxide detectors
sail sfbay at 6:43pm 08.16.20 A CO alarm should be located in the main cabin plus one in each sleeping area and smoke alarm in the |
||
Cruising RPM research
smokey73 at 6:35pm 08.16.20 Over analysis paralysis. No paralysis here - confirms what I am doing. |
||
how sturdy is the glasswork on 82 34ft oday
Davidasailor26 at 6:26pm 08.16.20 This won't cheer you up but here's a pretty scary thread about an Oday 30 losing its keel - O'Day 3 |
||
Cruising RPM research
smokey73 at 6:06pm 08.16.20 Nope. Two blade geared folder. Still though, measure twice cut once. |
||
Hunter 386 Window
Ralph Johnstone at 6:04pm 08.16.20 If you just have a leak but the hatch light (it usually is that large hatch light) is otherwise in g |
||
Cruising RPM research
Rick D at 5:59pm 08.16.20 @Rick D When I first got my 40.5 the Max Prop had a bit too much pitch and I could only do 3400 rp |
||
how sturdy is the glasswork on 82 34ft oday
CarlN at 5:52pm 08.16.20 I'm quite sure that it's a bolted on keel. The risk is that you broke a bolt or fractured the lamina |