|
Dale Bell
at 1:53am 01.20.05
1/983
I bought a used 23' boat with a Doyle furling jib. When I had this sail cleaned last Spring, the lo
|
||
|
Martin Bosman
at 12:30am 01.20.05
4/1130
My Oday 37CC has in the fore-peak sealing ( = fore deck ) 2 little sky lights. Does anybody know's i
|
||
|
Tom
at 11:50pm 01.19.05
0/862
Hi Dan; How did Navarre do during the hurricanes??? Is the anchorage at Fort Mcree still there??? W
|
||
|
Al
at 11:07pm 01.19.05
1/967
There seems to be excessive movement in my C34 rudder. It wobbled under power quite a bit just befo
|
||
|
Allan Lansche
at 9:33pm 01.19.05
6/1026
I have a 2003 Hunter H260 with Doyle mainsail. We were in > 21 knots of wind last time out and of c
|
||
|
MitchM
at 9:20pm 01.19.05
7/1553
Well for the 3rd time in a row the 'trucker hitch' tiedowns on our Seafarer 30 have slip
|
||
|
richard
at 8:53pm 01.19.05
8/1198
a few months ago a boat moved into the slip next to my sailboat. At first I didnt notice a problem b
|
||
|
Bob Todd
at 7:41pm 01.19.05
2/1058
I requested a quote from four sailmakers (Doyle included) and for the same material, same specs, sam
|
||
|
Shane
at 6:32pm 01.19.05
2/1004
My boat a 22 Catalina has a boalt rope on the foot of the main. Can I use that main as a loose foote
|
||
|
Bill
at 6:17pm 01.19.05
2/1075
The cabin sole in the galley of Someday Lady, my 1984 H34, is squishy wet from (I believe) the refri
|
||
|
Will
at 1:39pm 01.19.05
1/1005
Where is the bilge pum located? I have done a cursory look without success? It is not working so I c
|
||
|
Tim Welsh
at 1:09pm 01.19.05
8/1044
After all most two years of ownership I have finally decided to repair the wood in the aft cabin tha
|
||
|
Mike B
at 1:04pm 01.19.05
4/991
I have e-mailed Doyle Sails five times in the last two months and asked where I can get replacement
|
||
|
Mason McDaniel
at 11:43am 01.19.05
5/1114
Has anyone heard how the new Cyclades model compares to the 473? I'm thinking specifically about liv
|
||
|
gary16415
at 10:52am 01.19.05
2/1043
My 1992 Hunter 27, has a four panel companionway hatch, made up of Two acrylic(smoked glass look-al
|
||
|
Rich
at 10:27am 01.19.05
2/802
What are the steps to securing an outboard motor for the winter? I am planning some three day weeke
|
||
|
Dan Guzman
at 10:19am 01.19.05
1/1201
I was hoping I can get a little bit of help. I was told that theres a way to set up a bungy cord on
|
||
|
John
at 10:14am 01.19.05
12/1383
I do not have power at the switch panel in the cockpit but can start the engine by shorting out the
|
||
|
mike C16582
at 10:07am 01.19.05
7/837
the 3rd annual O'DAy owners "rOnDAYvous" will be this summer!! Details to follow!!!!!!!!!!!!!!!!!!!
|
||
|
Ryan Tuohy
at 8:52am 01.19.05
3/1062
OK, this is probably pretty basic for many of you (especially Bill C.), but could someone please out
|
|
Issues removing cutless bearing.
jonelli at 9:05pm 02.28.21 Does the shaft come al the way out without dropping the rudder? |
||
|
Issues removing cutless bearing.
snoopy_ at 9:03pm 02.28.21 Some boats have set screws, mine does not. I asked a few owners on facebook and all that repsonded |
||
|
Swim ladder step repair
dLj at 8:44pm 02.28.21 @dLj I strongly suspect that you have more engineering background than I do, however the chart give |
||
|
Issues removing cutless bearing.
snoopy_ at 8:29pm 02.28.21 In reading these replies and rereading the manual I suspect that the collets may not be making conta |
||
|
Follow up to creating Seatalk Network
LeslieTroyer at 8:02pm 02.28.21 I believe John is correct. The power cable for the Axiom just powers the axiom, not the buss. In o |
||
|
Fuel valve location
fullbore at 7:49pm 02.28.21 I could use pull handle at cockpit and find where that cable leads... Thanks BigEasy (from N.O.?) |
||
|
Fuel valve location
BigEasy at 7:43pm 02.28.21 On my 343, the valve is on top of the fuel tank. There is a pull type handle and steel cable, that |
||
|
Boarding step build
Hayden Watson at 7:41pm 02.28.21 Hayden, what does your written moorage agreement say? "2. Storage of anything on piers or floats i |
||
|
US Coast Guard Documentation turnaround time
BigEasy at 7:38pm 02.28.21 Last time I did an initial documentation, it took approximately 12 weeks, during relatively normal |
||
|
Issues removing cutless bearing.
weekendrken at 7:38pm 02.28.21 We tell customers not to rent our cutlass tools until the strut/bearing is properly prepped. They m |
||
|
Glow plugs $$$$$$
Rich Stidger at 7:18pm 02.28.21 If it is Perkins or Volvo parts you need, try: https://www.parts4engines.com But I really thought |
||
|
What is the one thing on your boat that you like the most?
dLj at 7:07pm 02.28.21 The one thing that I really like on my boat is the way that the toe rail is designed. This one is |