jerry_911
at 5:26am 08.02.21
3/89
Hull beyond repair. Is there any value in a sail drive? Boat has an outboard bracket so the sail d
|
||
Crazy Dave Condon
at 5:11am 08.02.21
9/1479
Recently, I received a request from out of the country to be accepted to my personal email contact l
|
||
mikemoyer
at 7:17pm 08.01.21
8/1241
I spray painted my portal black using Krylon Fusion All-In-One Paint + Primer in flat black. Some of
|
||
pclarksurf
at 6:28pm 08.01.21
3/626
196687196688
|
||
kodiak1120
at 6:25pm 08.01.21
6/1002
I just installed two new 6.5" speakers in the cockpit of my Beneteau 37. I had to cut the holes a l
|
||
DAVA390
at 4:57pm 08.01.21
3/625
Shortly after purchasing my Precision 23 8 years ago i discovered that i had been hoodwinked. About
|
||
CaptBob
at 3:19pm 08.01.21
8/1989
Hi, I have a new 315 on order and was wondering about instrument placement. I am only having the i7
|
||
Michael Davis
at 3:13pm 08.01.21
13/2361
196682 Again , we are the only two boats here. Solitude so close to home.
|
||
Voyager1
at 2:06pm 08.01.21
0/509
1. Has anyone replaced stem seal without removing the head on a Yanmar 2gm20f. Is it reasonable poss
|
||
john6206
at 12:32pm 08.01.21
2/710
Hey everyone, Exactly a year ago I bought a Mercury 5hp propane sail drive motor. So naturally i g
|
||
Voyager1
at 11:17am 08.01.21
3/770
1. Has anyone replaced stem seal without removing the head on a Yanmar 2gm20f. Is it reasonable poss
|
||
SailorElliot
at 10:16am 08.01.21
17/5249
Hello! I was wondering what the "weather limits" are for a Flicka 20 (example: 30 knots of wind, 4
|
||
jssailem
at 8:25am 08.01.21
2/1020
|
||
waterman30
at 7:08am 08.01.21
18/3366
Hi. I am new to the forum. I have never owned a water ballast boat before but am considering a 240.
|
||
apagano
at 4:48am 08.01.21
3/640
Hello all, i have a Hunter 49 that almost all stock latches, both doors and drawers have mostly fail
|
||
patbratton
at 3:26am 08.01.21
3/902
The bilge area under the rear if the cockpit has about three inches of water. there are no limber ho
|
||
Yangyangyyy
at 9:04pm 07.31.21
3/600
I'm trying to Change the fuel cap and seat ( on port stern deck) on my 2003 Beneteau first 36.7 Sin
|
||
dLj
at 5:42pm 07.31.21
78/9031
I am not well versed in using all chain anchor rode. So I've been researching chain snubbers. I fin
|
||
Sail question (1)
Dil
at 2:56pm 07.31.21
30/3004
Recently I purchased a new sail Today I noticed near the head of the sail the leach makes contact wi
|
||
Apex
at 2:28pm 07.31.21
5/806
Putting out in another thread as well, but have friend with hunter 34 that just lost shaft, strut an
|
Do you folks strap your boats to your trailers?
Rick Webb at 6:58am 12.15.24 Definitely tie it down. Use two on the stern, one on either side and an additional tie down at the b |
||
What is "residual value"?
Kings Gambit at 6:13am 12.15.24 If you were to plot a boat's value from when it is new to what it is 50 years later, I think you it |
||
What is "residual value"?
shemandr at 6:00am 12.15.24 If you were to plot a boat's value from when it is new to what it is 50 years later, I think you it |
||
Do you folks strap your boats to your trailers?
Sailor Sue at 4:47am 12.15.24 Tie it down. Run a strap over the cockpit to the trailer frame. Yup, a heavy duty ratchet strap ov |
||
Do you folks strap your boats to your trailers?
Indysailor at 4:46am 12.15.24 I don't think I have ever seen tie down eyes on the transom of any trailer sailor, but if I were goi |
||
Do you folks strap your boats to your trailers?
dlochner at 4:33am 12.15.24 Tie it down. Run a strap over the cockpit to the trailer frame. |
||
Yanmar Engine mounts.
Ralph Johnstone at 9:52pm 12.14.24 from what I remember the 100# mounts go in the front and the 75# go in rear, can anyone confirm tha |
||
Yanmar Engine mounts.
jssailem at 7:17pm 12.14.24 I'm very satisfied with the decrease in vibrations. Those would be bad Vibrations. I suspect now |
||
Yanmar Engine mounts.
MikeHoncho at 6:07pm 12.14.24 how much a pain the in the azz changing the mounts are and the following alignment, I'd pony up for |
||
Ice Box Conversion
MikeHoncho at 6:02pm 12.14.24 double everything sounds like a terrible idea. They will be fighting one another and power use will |
||
Engine alignment needed (1)
Ralph Johnstone at 2:18pm 12.14.24 Hard to get precise measurements without the shaft in a lathe with a precise support while turning |
||
Hunter 27 Cockpit Instrument Access (1)
Ralph Johnstone at 1:31pm 12.14.24 Instrument may be mounted with double sided tape after wires are fished through the space between b |
||
Engine alignment needed
dLj at 1:14pm 12.14.24 I've been told I'm both after a few drinks :what:. I prefer to use a dial indicator like this : |
||
Blue Horizon at 1:06pm 12.14.24 Haven't been online in a while. Thought I'd post this in case someone revisits this thread. I ha |
||
Upgrading to the Raymarine linear drive
kappykaplan at 12:32pm 12.14.24 I agree. I went through the same thing. Replaced the old wheel pilot with a new one and was very un |
||
Engine alignment needed (1)
Ralph Johnstone at 12:29pm 12.14.24 if you are bent or out of true. I've been told I'm both after a few drinks :what:. I prefer to |
||
Upgrading to the Raymarine linear drive
Mike Oldak at 12:22pm 12.14.24 I think Raymarine just made an incredible mistake in requiring 34 foot boats to use their linear dri |