Stephen M
at 5:54am 08.23.21
9/3576
I am going to change out the coolant in our Yanmar 4JH2-TE motor. I would like to get any tips, advi
|
||
NYSail
at 12:45am 08.23.21
7/1079
|
||
stricklandmma
at 11:10pm 08.22.21
28/2507
hello everyone, I just purchased my first sail boat. I've actually never been on a sail boat do this
|
||
mike ashton
at 11:07pm 08.22.21
11/1674
I want to retrofit a microwave in the cupboard above the stove in my 355. I understand 355's sold in
|
||
MikeSea
at 7:18pm 08.22.21
7/3414
Hi everyone. I recently bought a 1995 Hunter Legend 35.5 with a Raymarine autopilot system which use
|
||
Richardwm
at 5:48pm 08.22.21
16/3572
Hi guys. Hope your sailing season is going well. Mine sure is. I am considering buying a sock for my
|
||
artboas
at 5:47pm 08.22.21
1/464
After 2 close calls with the 50 amp shore power inlet almost burning up, I decided to replace it. Th
|
||
KristineDC
at 4:45pm 08.22.21
5/1393
Hi Hunter owners, has anyone replaced their cabin table? Ours broke on our Hunter 326 and the only r
|
||
SandyFrank
at 3:44pm 08.22.21
2/707
Hello all, I do not remember what rabbit hole I was going down but found this old 40.5 listing in N
|
||
Mark Maulden
at 3:40pm 08.22.21
6/1014
Anyone know how this monitor handles a bank and a separate start battery with an ACR In between?
|
||
Astromech1
at 2:35pm 08.22.21
3/829
Over the last few days I had some diesel leaking into the bilge; I not had this happen before. I've
|
||
Murgatroid
at 1:17pm 08.22.21
7/1858
My, new to me, 76 HMS 23 is cutter rigged, last night in very, almost non existent winds, I started
|
||
Mooseman
at 12:45pm 08.22.21
53/6057
Hello All! I just joined the forum today as a guy new to the sailing world. I caught the bug 1-2 ye
|
||
capta
at 11:23am 08.22.21
18/2272
***Update. We got to the boat and the highest wind speed it recorded was 59.8 knots. I sneeze faster
|
||
Clutch Cargo
at 11:20am 08.22.21
0/498
Hello All, I've posted this in the "Ask an O'day Owner forum but thought I'd also try the "Bigger Bo
|
||
tadd5181
at 10:53am 08.22.21
4/582
My small solar panel set just behind the mast on my Hunter 430 (built 2000) is a raised ripple...I n
|
||
Don Guillette
at 10:23am 08.22.21
25/12725
I was in So Ca last week visiting my old stomping grounds (Shoreline Marina, Shoreline YC and Los Al
|
||
HubertMagni
at 10:22am 08.22.21
8/2302
I've got an old O'Day 22 project boat on a bad trailer. I have a newer trailer for it but I don't kn
|
||
SailorElliot
at 9:37am 08.22.21
5/1220
|
||
Mark Lauer
at 9:09am 08.22.21
1/1426
It finally happened that the removeable fiberglass helm seat on my Catalina 309 #65 fell off the ba
|
Reverse diagonal shroud disconnect for winter cover?
marcham at 9:46pm 02.04.25 If you don't mind me asking, how many boat units for the cover? I have essentially the same boat and |
||
Looking to replicate this transmission cable bracket.
marcham at 9:43pm 02.04.25 The clamps that hold the cable onto the bracket would be available anywhere that does engine rigging |
||
Motorhome Mariners
Will Gilmore at 8:00pm 02.04.25 Or if you call fenders "bumpers." I resemble that remark. You might be a motor home Mariner if yo |
||
Runaway diesel
dLj at 7:23pm 02.04.25 My terminology may not be precise or even correct, and may be confusing. Go back to the section of |
||
Looking to replicate this transmission cable bracket.
dlochner at 4:28pm 02.04.25 The aluminum bracket significantly changes the angle between the cable and the shift lever on the tr |
||
Raymarine Auto Pilot
Thinksnow at 4:24pm 02.04.25 It sounds like the rudder transducer is being damaged by the extreme AP movement. I don't believe t |
||
Is the leak from the through hull
Tally Ho at 4:01pm 02.04.25 If the nut is really tightened just on the pan liner, that is not good and needs to be corrected. I |
||
Motorhome Mariners
Urban Hermit at 3:56pm 02.04.25 Ain't nuthin you kain't do iffen you put yo mind territ, so doan nobody trita tell yo how to run yo |
||
Motorhome Mariners
Urban Hermit at 3:48pm 02.04.25 If your generator has more hours on it than your engine. |
||
Looking to replicate this transmission cable bracket. (2)
Ralph Johnstone at 3:45pm 02.04.25 ................ that are very likely aluminum. I'd check with McMaster Carr or Amazon for a SS |
||
Selden Rodkicker 591-300 (2)
Tally Ho at 3:38pm 02.04.25 I did find one! https://www.gasspringsshop.com/gas-spring-replacement/?msclkid=89a5c5059fc81a1536 |
||
Motorhome Mariners
Tally Ho at 3:21pm 02.04.25 You might be a motor home mariner if your cooler is the best part of your boat :beer: Greg |
||
Cutless Bearing Set Screws
Tally Ho at 3:16pm 02.04.25 They screw into the prop strut and touch the bearing. I'd be more concerned about the strut/screw c |
||
Cutless Bearing Set Screws
Justin_NSA at 2:25pm 02.04.25 They screw into the prop strut and touch the bearing. I'd be more concerned about the strut/screw co |
||
Cutless Bearing Set Screws
LakeOntario270 at 2:14pm 02.04.25 I don't remember what my set screws were made of. They were 1/4" x 20 that I bought at the marina. |
||
Easy solution for Catalina 310 companionway crib boards
BC Bernie at 2:00pm 02.04.25 I went super simple: Home Depot - used a sheet of corrugated roofing sheet. Cheap. Strong and light. |
||
Runaway diesel
dLj at 1:59pm 02.04.25 You kind of changed the focus from "the engine has to be at 200rpm to start" to something about han |