|
Jack4873
at 12:56pm 08.14.08
1/1193
As I posted under general interest, I got dismasted last weekend so now I need a mast. Anyone know o
|
||
|
Panacea
at 12:54pm 08.14.08
2/1483
I have a Hunter 31 1987 and suspect I have a leak from the toe rail on the stbd side (forward - just
|
||
|
gravy26
at 12:23pm 08.14.08
3/1772
I believe I lost one of the 2 main bearings this past weekend. It started making a terrible noise a
|
||
|
Luftig
at 10:37am 08.14.08
3/1495
Has anyone figured out a clean way to keep the plex cover over the instrument cover up when you are
|
||
|
Warren Milberg
at 10:23am 08.14.08
21/2261
This story was in the BoatUS "Seaworthy" magazine and is quite amazing....
|
||
|
Alan Dyer
at 10:14am 08.14.08
1/1832
I recently purchased a P30. I am replacing all the ports and windows. Beckson has sent the 4 small
|
||
|
Paul T
at 10:04am 08.14.08
1/961
Hi everyone! I'm planning a BI trip in September (weather permitting) on my O'day 23. I know the is
|
||
|
rardiH36
at 9:42am 08.14.08
19/8966
This weekend, I will be replacing my very old "who knows how long its been on the boat?" mainsail ha
|
||
|
soling42
at 9:11am 08.14.08
28/3850
I'm talking about the big a$$ wharf rats that are partying on my boat when I leave. Luckily(?) they'
|
||
|
Kevin
at 9:08am 08.14.08
0/1096
OK...I've bought my Tohatsu 6hp, Garelick 71090 motor mount, and had a machine shop manufacture me a
|
||
|
tsiptom
at 8:25am 08.14.08
7/1538
I hate my 9.9 Yamaha motor; it is so dam heavy how can I trade it in or sell it (it works well)
|
||
|
rchuyck
at 8:25am 08.14.08
2/1414
I just purchased a '84 Hunter 27. When the boat was derigged the mast wiring was cut at the mast ste
|
||
|
newly anonymous
at 8:22am 08.14.08
7/1038
Yesterday, while installing a wind turbine generator, I discovered that my amp-hour shunt, which is
|
||
|
walt
at 8:14am 08.14.08
6/5168
My boat has a 1990 or so Honda BF8 (8 hp) outboard which had a bad charging system and I finally got
|
||
|
viduta, trish dora jane
at 8:03am 08.14.08
3/1388
Okay, I just must be visually impaired since I can't seem to see the gimballing feature hardware (re
|
||
|
viduta, trish dora jane
at 7:53am 08.14.08
2/1495
We just purchased a 1988 Catalina 27. PO is out of country for a bit so can't ask him. Stove top i
|
||
|
cat30
at 7:29am 08.14.08
4/1358
I've got a ray 100 handheld vhf with tired old nicad batteries. i would like to rebuild the battery
|
||
|
Coyote
at 7:03am 08.14.08
3/1211
will be removing the Cowl in the aft berth to reveal the Steering Cables and Quadrant any suggestio
|
||
|
Barry
at 5:39am 08.14.08
0/1202
Well ,we sailed her on Lake Temiscaming and she behaved very well.....that is until the mast base co
|
||
|
Alan11634
at 5:08am 08.14.08
4/1437
Anyone recommend an online Yanmar dealer that supplies the Tennessee area. Need routine maintenance
|
|
Update
Ralph Johnstone at 10:42am 01.10.22 If anyone can figure a way to rewire the circuits in your brain for a complete recovery, it's you. |
||
|
What is the Purpose of This Toe Rail Fitting
Parsons at 10:39am 01.10.22 If installed by PO, ya prolly want to make sure that it is through bolted with backing and not simpl |
||
|
Dinghy deck stowage and getting on board. Hunter 336
Ralph Johnstone at 10:32am 01.10.22 Do not want to tow dinghy but have easy access/launching. Don't see how you would have easy acces |
||
|
Traditionally made boat fenders
jssailem at 10:25am 01.10.22 Thinking about this. By adding the noodle you have created a floating rope fender. In a reasonable s |
||
|
New tool :) (1)
jssailem at 10:22am 01.10.22 Justin. I know you posted your tool last January. In honor of your 2021 post I offer a clever tool t |
||
|
Wind angle
jeepbluetj at 10:09am 01.10.22 Likely you're going to go up there. It's probably stuck. Go sail around it a circle and see if the a |
||
|
Traditionally made boat fenders (1)
rbringle at 10:01am 01.10.22 I have made three of them, two of natural fiber rope, and one out of synthetic rope. But it was long |
||
|
Point to ponder: furling the jib
Dalliance at 9:53am 01.10.22 Another cause of furling jibs being shredded in a storm is not getting a tight furl, which can happ |
||
|
Update
Phil Herring at 9:03am 01.10.22 Hi Rodd, very very happy to hear from you! That's quite an image and it does seem like a miracle tha |
||
|
More on Maine Sail
Scott B at 8:55am 01.10.22 Rodd, so great to hear from you. I think if anyone would pull off a miracle like that you'd be the |
||
|
Safest knot for dock line on a o ring...
Kings Gambit at 8:53am 01.10.22 Terry. You are dead right. I just uploaded the vid without watching it. gary Shame. Anyone can fin |
||
|
Update
Rich Stidger at 8:48am 01.10.22 It is good to hear from you directly Rod. Our prayers are for a continued recovery. |