|
Tonto's Revenge
at 4:50am 08.13.08
7/1222
I have sailed my 1974 V25 for three months now and am finally getting comfortable enough to let her
|
||
|
TI doug
at 8:23pm 08.12.08
21/11122
Hi everyone, I have a quick question. I have a 30'sailboat, in west central florida, 3 out of 4 doc
|
||
|
Thumper McDonald
at 7:33pm 08.12.08
5/1613
Hello, I've been lurking around this website over the past couple of years, soaking up tidbits of
|
||
|
Bob T
at 7:33pm 08.12.08
6/3457
I'm looking for info and experience with aftermarket UV protection for a roller furling jib. My rece
|
||
|
John
at 6:33pm 08.12.08
2/1065
I just returned from my boat where, among other things, I met Stu, who spent at least a couple of ho
|
||
|
blackcloud
at 5:51pm 08.12.08
1/991
The fuel guage on my Hunter 310 is pegged out below the empty mark. I have tried cleaning the elect
|
||
|
coralrec1
at 4:54pm 08.12.08
2/1603
I have a 1978 lancer here in oceanside ca and need to replace at least four of the opening/closing t
|
||
|
Capt. Kermie
at 2:12pm 08.12.08
0/748
I am not sure this is the right forum but I don't know where else. Here in the Pacific Northwest we
|
||
|
JoshGray
at 12:08pm 08.12.08
10/1198
Hope some of you guys with more experience can help me out there. I took my shoal keel 22 out to the
|
||
|
RS
at 10:50am 08.12.08
4/1559
I need a pic or two in regard to setting up the mainsail and boom, etc. any info/pics would be appr
|
||
|
hooyasailor
at 10:19am 08.12.08
4/2553
Hello, Folks, I have a new (OLD) boat! The trailer is shot (Rusted out) and I can't even move her ti
|
||
|
lancelot8602
at 9:43am 08.12.08
10/2329
I have inherited a 19' Oday Mariner, she is in pretty good shape. My wife and I have been learning
|
||
|
jdgrnt66
at 9:14am 08.12.08
1/1479
Hello all. I need to fill my CNG tanks and finding it hard to find refill stations in the tampa bay
|
||
|
tkanzler
at 8:36am 08.12.08
6/1123
The last post in the linked thread sums up both the problem and the reason why raising the switch wo
|
||
|
jim
at 8:11am 08.12.08
3/1102
How does one remove the compass to access the gear shifter linkage
|
||
|
Teak Refinishing (1)
Kjoe
at 7:02am 08.12.08
4/1182
I am in the process of refinishing the teak rubrails on my V-21. it was neglected for awhile so am
|
||
|
Maine Sail
at 6:09am 08.12.08
18/1764
Hi All, First, I know sailors are a cheap lot and I can be too but... Those of you who know me
|
||
|
BaySailerBill
at 5:47am 08.12.08
2/1083
Hi everyone, Last week I took a step that I hope was well placed. As some of you know I just fin
|
||
|
ChuckThomas
at 5:34am 08.12.08
1/1120
Did anyone hear about a catamaran in a wreck near the twin span?
|
||
|
sea_casper
at 5:09am 08.12.08
0/25
I have replaced the stock Rudder system including head plates and tiller, with an IdaSailor Kick up
|
|
Point to ponder: furling the jib
jssailem at 5:22pm 01.09.22 When I first wrapped my furler, The line was a bit loose on the drum. When I wrapped the sail in a s |
||
|
Exhaust Riser - Repair or Replace
Ward H at 5:10pm 01.09.22 I wouldn't dismiss the idea of cast pieces entirely. If you follow best practices for diesel opera |
||
|
Is compass light wired into stern running light on the 270?
sail sfbay at 5:07pm 01.09.22 Have you turned on the navigation light switch at the panel to check? Otherwise might do a function |
||
|
Point to ponder: furling the jib
heritage at 4:48pm 01.09.22 Another cause of furling jibs being shredded in a storm is not getting a tight furl, which can happe |
||
|
Looking for New Chart Plotter
snoopy_ at 4:29pm 01.09.22 If you have existing instruments and auto pilot that are all manufactured by same manufacturer, tha |
||
|
Safest knot for dock line on a o ring...
Terry Cox at 4:03pm 01.09.22 The other end (boat end) of the lines would be left straight to tie to the cleat. The Bing video s |
||
|
I still don't quite get rule #2...
Tally Ho at 2:33pm 01.09.22 I thank everyone (except maybe @Scott T-Bird ) for their thoughts, comments and insights. I sail oft |
||
|
I still don't quite get rule #2...
Tom J at 12:15pm 01.09.22 Maybe we have discussed this topic enough, but I would offer one example of what can happen when som |
||
|
Safest knot for dock line on a o ring...
Len Ingalls at 12:05pm 01.09.22 Slipped anchor bend. mPM8In947MY |
||
|
Point to ponder: furling the jib
BigEasy at 11:58am 01.09.22 I always furl the jib and have three wraps of sheets around the furled sail as well as tie off the e |
||
|
Looking for New Chart Plotter
BigEasy at 11:44am 01.09.22 If you have existing instruments and auto pilot that are all manufactured by same manufacturer, that |
||
|
Point to ponder: furling the jib
Tom J at 11:43am 01.09.22 Ditto that..............never know when we will have a 70+ mph wind storm. Never had a jib sail unf |
||
|
Point to ponder: furling the jib
Tom J at 11:34am 01.09.22 An easy way to add wraps to the furler line on the drum without removing the sail, is to release th |
||
|
Looking for New Chart Plotter
Stu Jackson at 11:30am 01.09.22 ...but you believe I should be well versed before asking anything, so I am asking pertinent questio |