djplatt@cogeco.ca
at 1:27pm 06.10.10
1/1349
Does any one have any ideas on tightening up the Genoa luff on an Oday 240. I am reluctant to tight
|
||
Bad Obsession
at 1:19pm 06.10.10
36/5051
I have never really experienced sea sickness to its fullest extent. A long time ago I think that I
|
||
nbabic
at 1:01pm 06.10.10
10/2801
I would like to know if the soft roll up solar panels are ok or should i buy the hard type ???
|
||
nbabic
at 12:58pm 06.10.10
4/1370
Just got my 1996 23.5 Hunter last August does anyone know how long the halyard should be for the mai
|
||
Sailorgirl626
at 12:48pm 06.10.10
3/4931
Am searching for a copy of an owner's manual for my 1990 Hunter 28. Can anyone help me with this?
|
||
seaward23
at 12:28pm 06.10.10
0/2552
I am considering buying a C-22. It is in an impounded boat auction at a local marina. Typical of d
|
||
MrMikey64
at 11:16am 06.10.10
4/1609
I realize this may not be the appropriate place for this inquiry, so I beg the forgiveness and indul
|
||
Larry14133
at 10:55am 06.10.10
46/7827
This is Sad. Abby Sunderland, the 16 year old attempting to become the youngest person to sail so
|
||
Texas Lake Sailor
at 10:01am 06.10.10
3/2272
I have a 1981 Hunter 30. The mast has no access plate on it. I want to run new wire for deck lights
|
||
Quoddy
at 9:32am 06.10.10
11/5178
Anybody got a Torqeedo? How do you like it?
|
||
Hermit Scott
at 9:23am 06.10.10
19/3182
The guys that own the powder coater that I use have a ski nautique ski boat. It's about 20' with a 3
|
||
Lynnie
at 8:48am 06.10.10
8/9963
Hello everyone. I have an old mast and do not have a flagpole, has anyone ever made a flagpole out
|
||
jbrock
at 8:42am 06.10.10
3/1589
I'm mounting a Plastimo Mini Contest Compass on my bulkhead where an old compass had been mounted pr
|
||
Edhavana
at 6:51am 06.10.10
11/3703
Hello group: Anyone has replaced the draw latches on the cockpit lockers on your Yamaha? I would
|
||
Roger Long
at 6:37am 06.10.10
13/3090
When I did my tightly scheduled science cruise last spring I based my planning on an average through
|
||
R.S.Cape
at 5:31am 06.10.10
8/3585
I am about to start on our companionway cover after the Sunbrella fabric arrives. To finish the edge
|
||
Tonto
at 4:22am 06.10.10
3/2976
Hi , I have a Hunter 240 the rudder floats and is extrmely hard to get it set in place ,is it norm
|
||
Carpe Diem
at 9:37pm 06.09.10
8/2758
Hello fellow O'day 27ers, My boat, Carpe Diem, a 1976 O'Day 27 was recently broken into at mooring.
|
||
j4jrevel@blueriver.net
at 9:27pm 06.09.10
2/1560
I have a 1999 Macgregor 26x that has sit for a few years and was wondering what to use when i buff
|
||
don kerr
at 8:32pm 06.09.10
1/3033
Does anyone know where to get replacment lenses for a 1970 Ericson 29.
|
Effects of disconnecting hydronic heater
sailme88 at 4:48am 05.01.22 It is all about flow....restrictions are the usual culprits.. The exhaust elbow is a prime location |
||
Raymarine Wheel drive autopilot on Hunter boat- to upgrade?
kappykaplan at 4:45am 05.01.22 ? things, I think. |
||
Effects of disconnecting hydronic heater
jviss at 4:31am 05.01.22 By hydronic heater do you mean the water heater, or do you have cabin heat? I don't think you'd plu |
||
Raymarine Wheel drive autopilot on Hunter boat- to upgrade?
jviss at 4:29am 05.01.22 when hinge get a little hanky. ? |
||
Funny Friday!!!
All U Get at 10:51pm 04.30.22 Not sure where you are, but was that Ever Forward? Norfolk. |
||
Elusive Leak in the Anchor Lockers of 1995 and Later Hunters
Mark Maulden at 10:46pm 04.30.22 How about fixing up a garden sprayer heavily laden with food coloring and heavily spray a certain ar |
||
Wetnesses under compression post
Mark Maulden at 10:38pm 04.30.22 Pull the mast. Then pull the compression post. Rebuild the pad for the compression post and reinsta |
||
Elusive Leak in the Anchor Lockers of 1995 and Later Hunters
JamesG161 at 10:13pm 04.30.22 Like you said after 24 years it must be either this bhKiqo-nqm0 Or Try another approach. I sugge |
||
New Catalina 30 Owner
mikeracca at 8:48pm 04.30.22 Well I decided to play around in Tinker Cad tonight and print a mounting block for the throttles. I |
||
Wetnesses under compression post (1)
Avi at 7:23pm 04.30.22 Looks like water been accumulating there |