Nuteak Deck (1)
Great_Lakes_Crosswind
at 2:44pm 03.25.10
2/1922
Does anyone know where I can find deck plans that show shape and deck layout? I want to cover my wal
|
||
JWH2050
at 2:08pm 03.25.10
2/1698
We are leaving tomorrow on our journey down the Arkansas River that we started in 2008. We started a
|
||
Newbie Sailor
at 1:58pm 03.25.10
39/9469
We just started sailing last summer for our first time. It was amazing until we got caught up in a
|
||
All U Get
at 1:01pm 03.25.10
25/6915
Hi all, I was recently talking to our marina owner about the winter storms and damage to the docks.
|
||
sailingtrouble
at 12:44pm 03.25.10
1/1274
I'm looking for some suggestions for an OB motor for our 1967 Javelin. We need a bit of help getting
|
||
pfchenier
at 12:25pm 03.25.10
2/1222
Hello, I'm in the process of changing the foss foam rudder (H260) I have to a Idasailor.I'm not s
|
||
rod1029
at 12:15pm 03.25.10
15/6852
So here is the Question at hand: does one control the vessel with the rudder, or with the direction
|
||
Pat T
at 11:42am 03.25.10
7/9793
It's that time again. Finally. I read in a previous post that VC-17 can be thinned using isopropyl a
|
||
MrUnix
at 10:35am 03.25.10
6/3918
First off, I'd like to say hello to everyone and introduce myself as this is my first post here. T
|
||
Steelshooter
at 7:33am 03.25.10
5/1457
Hi all, I'm getting ready to get my 1977 30 ready to put her back in the water and thought I would r
|
||
minvan91
at 6:18am 03.25.10
7/1881
I am trying to separate the coupling from the shaft on my 1992 hunter 35.5. I'm sure that many othe
|
||
Spiderjohn69
at 4:00am 03.25.10
8/2113
I've just purchased a 1993 23.5 that was part of an estate sale. The family was not familiar with t
|
||
Roger Long
at 3:33am 03.25.10
8/2270
By the end of the day, I should have installed one of the better ideas I've run across to increase r
|
||
rohare
at 8:55pm 03.24.10
10/4687
Hi all, I am preparing to make my first long (I guess that's relative) trip; from Long Beach harbour
|
||
CharlieCobra
at 8:07pm 03.24.10
8/2268
Finished the prep the other day. http://i234.photobucket.com/albums/ee13/CharlieCobra03/Beth/005-1.
|
||
sailaway78
at 7:53pm 03.24.10
14/2277
For me at least. While back was wandering around in a dollar store. I know, but it's really OK to
|
||
oldjags
at 6:07pm 03.24.10
2/1275
I'm getting ready to re-step the mast on my 1994 Legend 37.5 with the Hood roller furler and need so
|
||
seamansg
at 5:51pm 03.24.10
4/2715
Waxing bottom not a very good idea ect. Hi, I was told at the marine store that I can wax the botto
|
||
bobleeper
at 5:23pm 03.24.10
1/1594
Looking to replace the cutless bearing on a 36 catalina when I haul out next month. Understand there
|
||
fiestaMojo
at 5:21pm 03.24.10
2/4666
Hey all, my first post as a new owner of a 1981 Hunter Cherubini 33!!! I might have a slight problem
|
T3800 - Location of Macerator Pump?
Peggie Hall HeadMistress at 8:13pm 09.09.21 Good idea..but more importantly, rinse it out after every use. Waste is sticky...it causes impelle |
||
When the wind turns squirrely
Mikeeder1972 at 8:13pm 09.09.21 That pretty much explains almost every sail I've had on Flathead lake. It''s rather rare for us to |
||
Fuel delivery issue
JRT at 8:05pm 09.09.21 Hey Fleet, give me a call. Been traveling and busy at work. I'm almost certain you need to fill th |
||
T3800 - Location of Macerator Pump?
jviss at 6:48pm 09.09.21 I'm going to try reversing polarity to the motor, see if I can jog it loose. If I get this fixed, |
||
T3800 - Location of Macerator Pump?
jviss at 6:45pm 09.09.21 Thanks Peggy. I don't think there's a vented loop in between, none is shown on the diagram in the o |
||
Splicing 4mm dyneema to double braided polyester
thinwater at 6:40pm 09.09.21 dyneema to doublebraid |
||
T3800 - Location of Macerator Pump?
Peggie Hall HeadMistress at 6:38pm 09.09.21 It's unlikely to be under the tank unless there's a lot of space below it..although it could be behi |
||
Yanmar / Kanzaki gearbox dipstick threads broke
BigEasy at 6:34pm 09.09.21 Heat, Oil, & plastic threads are not a good combination. Very common to hear about the plastic dip |
||
Replacement Traveler Part for H-34
Mike Oldak at 6:00pm 09.09.21 I still have the H34 traveler and other pieces looking for a good home. |
||
New to me needs some work (advice)
smokey73 at 5:52pm 09.09.21 Neither would I consider permanent; even 3M-5200. One wants to make sure that whatever is used bel |
||
Yanmar / Kanzaki gearbox dipstick threads broke
DayDreamer41 at 5:40pm 09.09.21 My 2GM20F is about 33 years old, and still has the original dipstick (I assume). I guess I am jus |
||
T3800 - Location of Macerator Pump?
jviss at 5:22pm 09.09.21 Turn it on and follow the sound Thank you, Sherlock, but I said it failed; it doesn't make any noi |
||
Yanmar / Kanzaki gearbox dipstick threads broke
Tally Ho at 4:54pm 09.09.21 My 2GM20F is about 33 years old, and still has the original dipstick (I assume). I guess I am just |
||
Throttle and Transmission Replacement Cables
PaulK at 4:44pm 09.09.21 You could try tying messenger lines to the ends of the cables and pulling them out. You'd then have |
||
Replacement Traveler Part for H-34
Fast Ed at 4:24pm 09.09.21 Hey, YVRguy, What you are looking at is a cheek block. This is a standard block that you could pick |
||