abk
at 6:43am 06.14.14
10/1180
Here is the Winch on the trailer and the coupler in a separate shot. Problem1 The winch handle was
|
||
dparilla
at 6:41am 06.14.14
14/3222
I got underway yesterday for Annapolis. Only an hour after leaving the dock (in no wind) we heard a
|
||
sfr
at 6:26am 06.14.14
3/816
Pulling my Hunter 260 to San Francisco in September going to moor boat, park truck and trailer at th
|
||
capdabney
at 5:21am 06.14.14
8/1502
Ok, I have made up my mind as to which model of C22 i'm looking for. Going for the 1st generation.
|
||
star302
at 4:19am 06.14.14
4/1250
Hi, We have a Hunter356 2002..Our dinghy has a 5hp engine. We have forspar nova davit system for
|
||
shortstop
at 7:56pm 06.13.14
5/1402
Hi all, you have a wonderful forum here. My first post. I'm looking for a book or online source th
|
||
Arch Speakers (5)
LiveAloha
at 5:55pm 06.13.14
0/1009
Just On step closer to being complete. Manufacturer has promised completion by Monday. I guess its
|
||
judsonj
at 3:29pm 06.13.14
10/1704
Hey, I just purchased this boat despite one or two issues (several of which I only discovered last n
|
||
trevor1955
at 1:04pm 06.13.14
7/5014
Ahoy there! I have inherited a mixture of different line sizes on my Catalina 27 (1988 with wing ke
|
||
schooner39
at 12:19pm 06.13.14
15/1649
I have just purchased a 1998 P42. During due diligence period, the pressurized fresh water system ap
|
||
Arch Speakers (3)
LiveAloha
at 12:01pm 06.13.14
23/7929
New replacement arch speakers in process. Stopped at manufacture to check out the progress. This i
|
||
sailfree20770
at 11:21am 06.13.14
5/1171
The mast base on my boat is different than shown in the Hunter manual. So the mast base details of t
|
||
sailfree20770
at 10:53am 06.13.14
0/672
From previous posts it seems the halyard rollers under the forward part of the "windshield" cause pr
|
||
Justin_NSA
at 10:26am 06.13.14
16/1541
My pop top is wearing through the gelcoat where the sliding hatch makes contact with it. The sliding
|
||
wufibugs
at 9:53am 06.13.14
16/3241
Dave's thread about adding storage where his legs would go were he to try to sit at the nav table in
|
||
mike C16582
at 9:46am 06.13.14
2/940
greetings, my name is Mike Colucci and I am the new owner of hull #20. (ex. Shooting Star) now re
|
||
MickP
at 9:21am 06.13.14
10/1288
Just wanted to say thanks for all the helpful advice i have received from the forum on this project.
|
||
drfstop
at 8:21am 06.13.14
2/1008
Does anyone know the BTU's of the 323 LP gas stove? Thanks
|
||
capdabney
at 7:48am 06.13.14
13/2053
Some body please tell me about bulkheads. I looked at a later model new design that is showing de
|
||
CJRoxs
at 7:37am 06.13.14
10/2060
I'm sure there will be a lot of puns in this thread but here it goes (no pun intended). My porta
|
engine leak antifreeze
Tally Ho at 7:07pm 05.30.23 I am going to get a small mirror and try to see the back of the engine. That seems to be where the |
||
Installing Anemometer on Masthead - what should I expect?
shemandr at 6:08pm 05.30.23 For the education of the forum, do you think you could have done the task from a bosoms chair? |
||
engine leak antifreeze
CharlieAnn at 5:52pm 05.30.23 I am going to get a small mirror and try to see the back of the engine. That seems to be where the l |
||
Possible SmartPlug problem
jaysweet at 5:48pm 05.30.23 The last few fires in the marina were smart plugs. I do not know the details. Over time with my la |
||
1998 Hunter 376
Greg Mott at 5:48pm 05.30.23 Hi Rich, Thank you so much for getting back to me. This looks a lot like the crack I have at the b |
||
Continupus mainsail furling
danm1 at 5:47pm 05.30.23 If the line is moving freely through the mast winch then chances are it is too thin or too slippery, |
||
1998 Hunter 376
Terry Cox at 5:47pm 05.30.23 Hi Greg, Rich offers some sage advice. Lots of discussions on this site regarding cracks in the keel |
||
O'day 28 Needs a New Transducer (Airmar P79?)
Clutch Cargo at 5:37pm 05.30.23 Have you thought about installing one that shoots through the hull, eliminating any holes........My |
||
O'day 28 Head Finished
Clutch Cargo at 5:34pm 05.30.23 I think I know this boat....Is that you Pete? Could be......LOL |
||
O'day 28 Head Finished
Clutch Cargo at 5:33pm 05.30.23 Regarding the double clamping and length of the barbed fitting, ABYC only recommends double clamping |
||
Possible SmartPlug problem
Mark Maulden at 5:32pm 05.30.23 The last few fires in the marina were smart plugs. I do not know the details. Over time with my las |
||
Possible SmartPlug problem
jaysweet at 5:09pm 05.30.23 Not replacing a standard shore power cord based on one report of a failure in the absence of a defi |
||
Sealing shaft-log options (1)
ricksoth at 4:59pm 05.30.23 Here is the stuffing box alternative - plastic parts just for conceptualization. Bronze version beh |
||
Sealing shaft-log options
ricksoth at 4:52pm 05.30.23 Dave, how is creating an epoxy plug inside the tube just past (behind) the stuffing box cap replace |
||
Slow sump pump with backflow
Tally Ho at 4:48pm 05.30.23 Glad you got it sorted out. Jabsco is pretty proud of that pump! Hope it works out well for you. |
||