CarlosIsaza
at 8:37am 03.29.14
4/1324
I'm looking for new rudders for my 1997 (early 1997 model) 26X. I contacted bwyachts but they are in
|
||
YVRguy
at 7:44am 03.29.14
11/1764
Our Hunter 34 came from the previous owner with two Maxwell self-tailing winches for the jib sheets.
|
||
Jep17
at 6:56am 03.29.14
1/3610
Here is the documentary film of the tragic holing of Pplau. The honesty and sincerety with which D.
|
||
holdech
at 6:55am 03.29.14
7/1216
Ralph Folsom gave permission to the TrailerSailors Association for a link to his North Channel artic
|
||
tigerjohn10
at 6:18am 03.29.14
5/1481
In my O'Day 27 bilge, there is (was) a block of wood that apparently transfers mast support to the k
|
||
Doc_holiday
at 5:38am 03.29.14
10/1377
I was thinking of putting sail numbers on. I don't guess there is a formal assignment of numbers, h
|
||
maloutofoffice
at 3:52am 03.29.14
3/1709
Hi, I am fitting a Raymarine autohelm linear drive. The stock arm needs to be lengthened to suit
|
||
hunter285
at 10:05pm 03.28.14
2/1667
My boat has been out of the water for some time now I think 7 years and was given to me by the previ
|
||
RECESS
at 8:43pm 03.28.14
22/2776
We have a drift alarm that works well, but running the Chartplotter all night does use some power. I
|
||
Jhildy
at 7:46pm 03.28.14
4/1642
Just a general rigging question: 1. Do running backstays have one line to either starboard or port
|
||
choover
at 7:18pm 03.28.14
2/654
Is there a resource for an '84 Hunter 31 Owners Manual? Thanks in advance! Chuck
|
||
BayGull
at 6:55pm 03.28.14
3/4228
I've narrowed my search for a new boat down to the P18. Has anyone sailed one on the Hudson? My trip
|
||
jfschena
at 3:18pm 03.28.14
22/2018
Last season I could hear a creaking noise when moving the tiller. I knew the pintles were a little
|
||
LASailing
at 2:17pm 03.28.14
2/1455
I am basically having the same issue as Shipyard in: http://forums.sbo.sailboatowners.com/showthre
|
||
Ontario Guy
at 1:36pm 03.28.14
8/2004
Good day: I recall reading on the now defunct Hunter 28.5 forum of a fix to a starter problem in the
|
||
cluce
at 11:46am 03.28.14
1/860
Hi, We have power going to the control panel for our WP30 autopilot, but when you push the button
|
||
John Rushing
at 11:18am 03.28.14
10/2337
Hello All, I am skippering my 1984 Hunter 34 in the Newport Ensenada Race this year. The boat has
|
||
Ontario Guy
at 10:26am 03.28.14
8/4894
Good day: I will be installing a bimini on my Hunter 28.5 shortly but understand that some modificat
|
||
Ontario Guy
at 10:19am 03.28.14
3/761
Good day. As the snow is now starting to disappear off the boat tarp, the first item on my check lis
|
||
bobcat30
at 8:20am 03.28.14
6/1199
I need to replace the fuel sender unit in the diesel tank. Suggestions where to get the unit. I repl
|
Gray Enterprises Portlight lens replacement H33C
heritage at 5:17pm 09.25.22 A note on the pins.. Be extremely cautious removing and reinstalling the hinge pins. The little pos |
||
Integral Fuel Tank leak
rgranger at 5:15pm 09.25.22 Is it possible to put a bladder inside the existing tank? |
||
Boom kicker or topping lift?
mermike at 4:55pm 09.25.22 I like my Boomkicker. Just don't try to swing from the end of the boom. It will go badly. |
||
Yanmar Engine Mount Worries
mermike at 4:50pm 09.25.22 I'm a follow the manual kind of guy. I never, ever assume that the "highly trained technicians" at t |
||
Frustrated, confused, and dissappointed
SoSound at 4:27pm 09.25.22 Well, the short term solution was pretty simple, I unplugged the temperature sensor and the charging |
||
Bottom paint - Required? (in freshwater)
Jamesiv1 at 4:22pm 09.25.22 Wow. Read thru some of the threads and articles........ Looks like a lot bigger project than I antic |
||
Structural Foam (8)
teacherspet at 4:01pm 09.25.22 What tank did you replace with aluminum or poly. Im doing a refit on a vision 32 and po did not lav |
||
Invest 98L (1)
JamesG161 at 2:33pm 09.25.22 Through precise calculations and applying Science to maximum, John and I created our own model. |
||
Yanmar Engine Mount Worries
jaysweet at 2:26pm 09.25.22 As far as fore/aft vs. port/starboard differentiation in motor mounts: all I can say is that Hunter |
||
Gray Enterprises Portlight lens replacement H33C
kloudie1 at 2:12pm 09.25.22 A note on the pins.. Be extremely cautious removing and reinstalling the hinge pins. The little post |
||
Hurricane prep in mast furling
capta at 2:08pm 09.25.22 It would depend on the strength of the storm, but as a rule, I'd remove that weight from aloft. Ther |
||
Hurricane prep in mast furling
Davidasailor26 at 1:44pm 09.25.22 We pull ours IMF main in as far as it will go, then we disconnect the outhaul, wrap the clew around |
||
Yanmar Engine Mount Worries
dLj at 1:21pm 09.25.22 @Tally Ho - I would certainly want a way to measure the need to change a mount. Looking back at all |
||
Two Holder/Hobie 12s
AaronD at 1:17pm 09.25.22 @HenryHester : Could you say a little more about the painting process? What did you use, and how is |
||
Yanmar Engine Mount Worries
Tally Ho at 12:51pm 09.25.22 Just sayin', every 4 years to change engine mounts seems mighty frequent to me. I'd be looking to h |
||
Bottom paint - Required? (in freshwater)
sail sfbay at 12:48pm 09.25.22 How am i even going to do it while on the trailer? Do an internet search on "how to bottom paint a b |