Coyote
at 3:44am 01.15.15
20/3621
I am thinking of adding Sirius XM Satellite to my current aging Clarion Marine FM/CD Radio,, on my '
|
||
CaptDon01
at 10:54pm 01.14.15
2/873
|
||
Unknown Gypsy
at 6:55pm 01.14.15
5/2526
I have a Yanmar 3GMY diesel in my boat Unknown Gypsy, that starts and idles fine but when put into
|
||
tom flatley
at 6:53pm 01.14.15
6/3656
Have a Javelin- can't get the mainsail all the way up- maybe a foot from the top - but the boom han
|
||
DAVA390
at 6:30pm 01.14.15
6/1527
I was just browsing the classifieds, found an O`Day 192. In the description was the term "slab reef
|
||
bikelessman
at 6:03pm 01.14.15
11/3135
I'm a new 8.5 owner as of 3 weeks ago. Any 8.5 owners in the southeastern ma area? I've been going
|
||
trainmanjess
at 4:11pm 01.14.15
26/3144
hello all well last time I posted, it was about a cheoy lee midshipman 40 ft sailboat..... was re
|
||
pupluv
at 3:56pm 01.14.15
19/3955
Anyone ever used Barska 7x30 Deep Sea Binoculars? Less than $100 for binoculars with compass and ran
|
||
slowhandsailor
at 3:55pm 01.14.15
0/560
1979 hunter 27 When I got this boat it had a inboard penta that was a good mooring .. a solid block
|
||
fredanderson2000
at 2:46pm 01.14.15
26/4753
I am a new Marlow Hunter 40 owner. The boat has the mariner package and the Marlow package. Nice b
|
||
JerryA
at 2:11pm 01.14.15
2/931
Anyone headed to KW for the races next week?
|
||
gettinthere
at 1:52pm 01.14.15
9/1873
My 900 amp/hr house bank has been staying around 1.275 SG pretty well, until recently. We've been si
|
||
newfiedad
at 1:22pm 01.14.15
4/1797
I have a newly purchased Mac 26D. Among several items needing replacement is the line to raise/lower
|
||
Clark
at 1:15pm 01.14.15
3/1073
Just curious to learn what people think of the new model. I like that Hunter went back to FRP but t
|
||
jimbigler
at 1:13pm 01.14.15
19/8257
So I live in MN and got into sailing a couple years ago and I am so excited to hit the water as soon
|
||
Paul and Judy
at 11:19am 01.14.15
15/4525
I have a 1993 33.5 that has an light/buzzer system for the oil pressure control. I would like to in
|
||
elsky79
at 10:02am 01.14.15
14/1814
Does anyone know of a good replacement for my balboa 26 boom/gooseneck. my boom is a little bent, pl
|
||
centerline
at 9:57am 01.14.15
43/22622
some boats have dry interiors without the use of air conditioners/dehumidifiers and many others not
|
||
All U Get
at 9:51am 01.14.15
9/1699
Hi all, I have a Spinlock XA clutch that needs a handle. I can undo the four bolts but the pin h
|
||
Paul and Judy
at 7:47am 01.14.15
3/5128
Check this link for a free download of the Yanmar 3GM30 service manual http://www.motoren.ath.cx/Do
|
A story of the engine that could.... Then didn't
RoyS at 4:53am 08.13.23 When it fell beneath the level of the Heat exchanger, a siphon event occurred and water flowed up f |
||
Oday 20 Restoration
shemandr at 3:57am 08.13.23 Welcome. Check in here for advice and encouragement. Chances are very good that someone on this lis |
||
Measurements of the Cutlass Bearing?
RSHunter27 at 10:07pm 08.12.23 Is the shaft bronze or SS ? Also, when you get down there, check whether the shaft is centred in t |
||
need to know ohm of water level for 1997 hunter 310
Ralph Johnstone at 8:35pm 08.12.23 @CharlieAnn , have you come up with a make and model of your current level sensor as requested in po |
||
New owner!
Vincent Williams at 8:05pm 08.12.23 She is in the water at Safe Harbor Pilots point hull #11 Quite an ordeal getting boat and trailer he |
||
Measurements of the Cutlass Bearing?
Ralph Johnstone at 7:18pm 08.12.23 I disconnected the gearbox from the shaft and the engine re-fired and when not connected to the sha |
||
trailer info, Hunter 23.5, 1994
maddog2 at 6:20pm 08.12.23 Group, Does anyone have the Majic Tilt BG0088 trailer designed for the 240? Are the bunks and the |
||
Our Cherubini Chainplates Are 40+ Years Old -- Any Failures? (4)
chichiflys at 5:16pm 08.12.23 Yikes - yeah the backstay U-bolts are also on my list. Thanks for the tip. Seems like a much easier |
||
Topside Teak Trim
Gene Neill at 5:12pm 08.12.23 Remove it. That way you can re-bed it in the process, which probably needs to be done anyway. Two bi |
||
2008 H36 microwave replacement
jssailem at 4:55pm 08.12.23 Along with enough spares to build a complete boat from scratch Coffee powered boat building.. Noth |
||
Measurements of the Cutlass Bearing?
RSHunter27 at 4:54pm 08.12.23 Thank you for your reply. It was these numbers that I was looking for. Might I ask what year your h2 |
||
Measurements of the Cutlass Bearing?
heritage at 4:52pm 08.12.23 This is the one that fits my H27:. Morse BLACKFISH 1 X 1 1/4 X 4 Brass Bearing It is about an inch |
||
MID Season Hurricane Forecast Update. (1)
Tally Ho at 4:52pm 08.12.23 The hurricane forecasting group now says to expect 3-5 major hurricanes (> 110 mph wind) before the |