walmsleyc
at 8:28pm 03.16.17
6/1158
(previously posted on a Catalina forum by mistake) My rudder has been dripping rusty water for a nu
|
||
jonelli
at 6:25pm 03.16.17
7/3228
Hey All, I need help identifying the correct belt for this. I see a lot of D169 "For MK1 black housi
|
||
Captmayhem
at 6:17pm 03.16.17
5/878
I'm sure I'm not the only one getting emails from them, what's the catch?
|
||
guidera48
at 5:46pm 03.16.17
1/677
I am rebuilding a first 405 and I need to make new counter rails for the galley. Beneteau made a la
|
||
spadaforaj
at 5:18pm 03.16.17
1/420
Nice 2004 Hunter 41 with a really bad caulk job Does anyone know ehere I can get a replacement ed
|
||
BwWhisper
at 4:59pm 03.16.17
5/759
My 1.5" bilge hose is deteriorated to the point it is broken off 2" long in the bilge area. Anybody
|
||
Time 2 Cruise
at 12:50pm 03.16.17
6/1477
Has anyone had the pleasure to replace the inhaul and outhaul lines on the cited spar? The line just
|
||
Craig Cook
at 11:09am 03.16.17
1/651
I was reading the commissioning articles in Sail and Cruising World this month and they both reminde
|
||
jansan
at 9:33am 03.16.17
2/857
Can anyone advise on the size of the pulley (O/Dia, thickness and bore I/Dia ) for the masthead shee
|
||
Sefuller
at 9:13am 03.16.17
3/707
Looking for 1/2" BLACK 4991 VHB tape for my window replacement project. I have located an Ebay sell
|
||
JimHartnett
at 8:05am 03.16.17
25/5040
There isn't enough room to pull the transmission away from the engine. After about a half inch I hit
|
||
Alex111
at 5:52am 03.16.17
8/1400
Hi, I just bought a 2006 Hunter 25 without motor, which is the best Shaftt length for Them 20" or 25
|
||
SVPardonMyFrench
at 11:48pm 03.15.17
10/1433
if you are in Seattle or Vancouver, Desolation Sound is a must. Check out this third video of ou
|
||
Mark Maulden
at 11:11pm 03.15.17
54/3175
Do we have one? Couldn't seem to find such with a quick search. A lot of sailors talking of meetin
|
||
chemainiac
at 6:29pm 03.15.17
0/526
hi folks I cannot remove the screws on my 2006 26m bow sprit stantion base. I have attempted to leve
|
||
freeheelbillie
at 5:44pm 03.15.17
7/1123
Figured I might need the Safe For Work disclaimer. I have a Quicksilver 380, 10' dinghy rated for a
|
||
RussC
at 4:58pm 03.15.17
6/799
Not mine and I know nothing about it personally. https://oregoncoast.craigslist.org/boa/6042914427.h
|
||
PGIJon
at 2:02pm 03.15.17
11/848
Well the Progressive Insurance rep was here and they are going to pay for a new furler. My question
|
||
JamesG161
at 8:53am 03.15.17
6/1110
I got these .... COURTESY OF SOLDBOATS.COM I thought they would be of general interest. Where is th
|
||
rpludwig
at 1:16am 03.15.17
0/713
in case you're not on Stingy's mailing list, he just posted: Stingy Deals West Marine has their Spr
|
Compression Post - way to stop the bleeding?
Project_Mayhem at 8:11am 03.11.24 Project_Mayhem is there anything to seal without dropping the mast? I'm not familiar enough with |
||
Compression Post - way to stop the bleeding?
mavexe at 8:08am 03.11.24 Project_Mayhem is there anything to seal without dropping the mast? |
||
Compression Post - way to stop the bleeding?
Project_Mayhem at 8:04am 03.11.24 For a temporary seal, I'd use BedIT. Much easier to remove than a normal sealant |
||
Should I put a 9.9 HP outboard on my 32' Catalina?
Ted10028 at 7:42am 03.11.24 The boat in that picture has a rather low freeboard which makes it feasible to operate. My 25' has |
||
Should I put a 9.9 HP outboard on my 32' Catalina?
Project_Mayhem at 7:40am 03.11.24 The boat in that picture has a rather low freeboard which makes it feasible to operate. I'm guessing |
||
Changing batteries
Duluthwinger at 7:31am 03.11.24 Thanks for the comments I would hope to have the boat for at least 10 years ( hope I live that long) |
||
Compression Post - way to stop the bleeding?
Justin_NSA at 6:50am 03.11.24 Mine got plugged up from muddobbers (sp?) nests settling to the base. I installed an inspection plat |
||
Microwave on Hunter 306?
Crazy Dave Condon at 6:47am 03.11.24 And if all fails , contact. Al or Mike at SBO who are former Hunter employees |
||
New Restrictions for Boaters in the Exumas
shemandr at 6:47am 03.11.24 ... Set moorings won't tear up the bottom the way transient's anchors do. Is sea grass better for f |
||
Compression Post - way to stop the bleeding?
kloudie1 at 5:34am 03.11.24 welcome to the forum!! It usually is a result of plugged drain holes in the mast base. Small ports t |
||
Mattress for aft cabin
DSqr at 7:44pm 03.10.24 We bought our mattress from McWhorter in Fairbury, IL. We gave them our old mattress to replicate, b |
||
Kent Narrows Chesapeake
DSqr at 7:31pm 03.10.24 We chartered out of Rock Hall in October and our contract specifically prohibited transiting the Nar |
||
Broken Rudder
KeukaSailer at 7:23pm 03.10.24 Or you could make one yourself with simple hand tools...get a nice piece of 4/4 teak, mahogany, or c |
||
New Restrictions for Boaters in the Exumas
PaulK at 5:47pm 03.10.24 Maybe they're expecting the sea grass to spread into the clear sand bottom areas once people stop dr |
||
Puck Lights
chuckwayne at 5:35pm 03.10.24 I'm looking for 3", tap on/off, led puck lights to replace the lights we have with the micro switch |
||
Puck Lights
jssailem at 4:37pm 03.10.24 I have seen puck lights that are tap capable but battery powered. There are puck lights that are 1 |