Serving sailors online since 1997
 
 

Recent Topics

bugbitten at 2:39pm 05.01.17
S2
27/4111
I was sure my water tank gauge had gone on the fritz, as it dropped from nearly full to empty just a
C38newbie at 1:54pm 05.01.17
5/816
Has anyone come up with a better way to access anything not in front of the engine? I was replacing
Brian D at 1:31pm 05.01.17
13/1321
ROFLMAO at 1:39. CEQuDyuQFKE
bawlmer at 1:17pm 05.01.17
11/740
When I bought my boat in 2013 it came with 2 AGM batteries and a 2 stage charger that looks like ori
rsotomayor at 12:27pm 05.01.17
22/1520
I am in search of a whisker pole for my Benetau 321.Have not found a used one, (yet). West Marine ha
JimOpp at 11:31am 05.01.17
4/477
The genoa tack swivel on my 1994 Oceanis 351 interferes with the anchor shank when the anchor is in
pclarksurf at 10:33am 05.01.17
9/661
@CaptDon01 : one of your pictures on an unrelated topic started me thinking. I have been looking a
eweb101 at 9:57am 05.01.17
19/3840
Hi all, I have a "new to me" Beneteau 352 (same as 343) and the battery banks aren't acting like I e
Capri at 9:37am 05.01.17
5/802
Hello, Everyone. I have a an '81 O'day 22 and have a few of questions. 1. I would like some advice
knotatwork2 at 9:36am 05.01.17
12/1229
I am trying to find an inside the cabin 12volt dc plug hdtv amplified antenna without running a coax
HukilauMike at 9:32am 05.01.17
4/1084
135938 For the past two or three years, I've prepped my hull pre-launch by stripping the old wax off
thetone at 8:51am 05.01.17
5/862
I have a noise coming from the fresh water circulator pump. Has anyone had this happen? I wonder how
Jackdaw at 8:51am 05.01.17
71/4069
From the latest GOB cover and description. What's wrong?? t, Massachusetts, in Lyrical, his 1975 Ta
CloudDiver at 8:28am 05.01.17
1/291
Looking for any Columbia 38 Center-board owners or former owners; anyone with good general experienc
patrickkidd at 8:00am 05.01.17
1/796
hi! My clothes drawers always end up on the floor and closet doors flap open when close-hauled on s
watercolours at 7:52am 05.01.17
18/7330
Hello. Does anyone have any info on MarinAire? MarinAire seem to be quality units, but I can't fin
Zephyr-Jeffer at 7:50am 05.01.17
14/3012
I'm asking for advice / opinions to help me with a small repair. My Hunter 25.5 has cast-iron keel a
SwanAround at 7:43am 05.01.17
2/449
The spring pull that releases the clasp on the lifeline seems to have fallen out over the winter (go
Warren Milberg at 7:41am 05.01.17
30/1886
So....I've sold my boat. Boo hoo. I'm looking to find other mid-Chesapeake Bay sailboat owners in
womble at 7:06am 05.01.17
1/534
I have a 1993 C30. The opening port light lenses measure 12 x 5 inches. Does anyone know of a source

Recent Replies

stripping cetol from teak
odaydokay at 12:44pm 06.06.24
Thanks jssailem. I saw this response on the thread you referenced: Re: Removing Sikkens Cetol or H
Hap[py 15th Birthday to my LiFePo4 Battery
SPLETS at 12:23pm 06.06.24
Rod thank you so much for all your help!! You are such an incredible resource as most of us are do
Moving the traveller questions
FastOlson at 11:08am 06.06.24
Note also that moving a mainsheet connection forward on the boom may likely required changing to a m
Moving the traveller questions
fred1diver at 10:26am 06.06.24
The deck is very strong and I would add backing plates. I looked into getting a Bimini but the driv
3GM30F Service Issue
dLj at 10:04am 06.06.24
I would think you should have been able to get higher RPM's towards the end if indeed your rings wer
Color-matching gelcoat
docofthebay at 9:50am 06.06.24
Color-matching gelcoat
docofthebay at 9:48am 06.06.24
Moving the traveller questions
Don S/V ILLusion at 9:46am 06.06.24
Among the considerations here is the structure where you intend to move and support it as the load o
Mid-ship cleat location for O'Day 34/35
Stu Jackson at 9:14am 06.06.24
My main application is for a fore and aft spring line whilst in a slip with a secondary use for con
Curiosity might be making me overthink
dmax at 9:04am 06.06.24
As has been said, a difficult project. Though not as convenient, a much simpler way would be to add
3GM30F Service Issue
skunther at 9:02am 06.06.24
Have you run it for a number of hours with no change? dj I ran it for ~4 hours at WOT (3250rpm),
1987 Hunter 23 Rebuild   (1)
Skycap92 at 8:47am 06.06.24
Thanks for the advice on the glue residue. It's coming off easier than I expected. Next major questi
Curiosity might be making me overthink
Project_Mayhem at 8:43am 06.06.24
I think the most complex part of this project would be the water drainage channels in/around the lid
Backing screw hole for filling with epoxy
Project_Mayhem at 8:41am 06.06.24
Tape works very well to hold in epoxy. It also minimizes sanding. With a bit of practice you wont ne
Color-matching gelcoat
Project_Mayhem at 8:37am 06.06.24
I use a RAL color swatch to find the closest match and then have a local gelcoat supplier mix it for
Small Outboard Motor Stands
FDL S2 at 8:16am 06.06.24
Built mine to fit in a space in the garage. As stated above, used scrap lumber, works great. Min
Curiosity might be making me overthink
dLj at 7:36am 06.06.24
I think I'd be more inclined to develop systems to allow better access to that area from the inside.
Overtrimmed jib prevent pointing?
danstanford at 7:34am 06.06.24
For those of you finding this in a search some day, here is our official answer posed in the origina

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.