Serving sailors online since 1997
 
 

Recent Topics

Lisa at 5:38pm 11.26.17
26/4687
Can anyone tell me the length and diameter of the main sheet? We have in the mast furling if that ma
Charlie98117 at 4:34pm 11.26.17
10/1800
I recently replaced the burned out 110V indicator light on my panel and after doing that the Reverse
jmce1587 at 2:29pm 11.26.17
20/14674
have mast down and want to clean up and remove black marks, etc. Any recommendations on products an
danm1 at 2:06pm 11.26.17
20/3043
Got stuck head down in the starboard locker reaching for a battery yesterday on my new to me Hunter
arknoah at 1:46pm 11.26.17
19/3501
Hi, Got some problems with leaks in my 1984 Mac 15, or more specifically with water in the bilge an
njlarry at 11:21am 11.26.17
7/1965
Searched but no luck on this. Helping a friend winterize his power boat for the first time. (Searay)
marchem at 11:15am 11.26.17
4/1054
I read a write up in an old MainSheet magazine about replacing the slides on the drawers under the b
LakeErieSailor at 9:55am 11.26.17
3/956
Having traded a 27 foot sailboat (which was in terrible shape) for this C22 swing-keel camper top wh
dph123 at 8:40am 11.26.17
2/784
I suddenly have a leak in the aft cabin of my 1998 Hunter 310. The water is pooling in the low spot
Ethanol   (1)
bawlmer at 7:45am 11.26.17
32/2383
Fellow Sailors. I know this issue pops up in these forums many times but I saw something encouraging
Jeff Gray at 7:38am 11.26.17
4/962
Hi All New member, here. We recently purchased a 260 and now can't wait for spring. Boat is a till
rsotomayor at 7:30am 11.26.17
11/1354
Good morning: What would be a good choice for solar panels for a Benetau 321? Requirements are ver
dont08901 at 6:38am 11.26.17
0/564
i had a slight separation between the aft end of the keel and the hull. I used a flexible epoxy to r
Babette04 at 4:21am 11.26.17
18/1902
I am fortunate enough to keep my boat in my yard We had solar panels installed while the boat was in
Sumner at 5:47pm 11.25.17
6/2228
http://1fatgmc.com/boat/mac-1/2017%20Lake%20Powell-Hite/17-10-4%20LP-2.jpg Dottie and I got to spend
miguelgdelrey at 5:07pm 11.25.17
23/2204
Hello. Does anybody knows where the Fluxgate Compass is located in a Hunter 49 ? Miguel
rgranger at 3:24pm 11.25.17
16/1451
143962 143961 Hey All: Today was a watershed day. If you have seen my earlier posts on the H26, yo
Rangerbill at 1:06pm 11.25.17
8/1427
If anyone happens across a Chrysler 26, with a trailer, and in project boat condition, please post b
chrisferro at 8:39pm 11.24.17
3/1032
Hello all, Does anybody know what the waste tank dimensions are for a 1992 Hunter 30T? If the tank
alanbe at 5:45pm 11.24.17
1/756
Hi All, I have a Beneteau 461 built in the USA 1998. It was in the Moorings Charter fleet as a Bare

Recent Replies

Hunter 41 AC Builders Plate
JamesG161 at 9:41pm 05.23.24
You can get a complete History of your Hunter 41 here Boat VIN Lookup / Hull Identification Number
Hunter 41 AC Builders Plate
JamesG161 at 9:32pm 05.23.24
You need your Hull ID number which normally found on the Rear Starboard side. Jim...
23.5 outboard motor
Southern Crux at 9:01pm 05.23.24
Does anyone have a rudder they bought from Rudder Craft
stickinthemud57 at 8:45pm 05.23.24
If I am not mistaken, Rudder Craft manufactured the rudder I bought through Blue Water Yachts severa
windvanes for hunter 33 de 2004   (1)
Windpilot at 7:59pm 05.23.24
224934 I have a windpilot Pacific model on a 1999 H410
Seeking a Harken 140 Lead Block with Cam Cleat
Hello Below at 6:15pm 05.23.24
I would get on the phone quick and start calling around. HARKEN 140 Pivoting Big Bullet Exit Block
In mast Halyard Swivel
Hunter 37 Aussie at 4:43pm 05.23.24
Hi Guys, thank you for your help i gicve them a call. thanks regards Paul
Does anyone have a rudder they bought from Rudder Craft
Rmalko at 4:13pm 05.23.24
Thank you for your reply and that information. We are going with Rudder Craft for our Cat 30.
Does anyone have a rudder they bought from Rudder Craft
Rmalko at 4:11pm 05.23.24
I have a Ruddercraft rudder on my 19ft Mariner, bought by the previous owner. I love it, especiall
Roller furler extrusions pulled apart
kappykaplan at 3:03pm 05.23.24
David, if the rigger can't pull the extrusions together, it's not likely that you'll be able to find
Catalina 27 outboard hp question
pgandw at 2:58pm 05.23.24
I had a Chrysler 9.9hp Sailor 250 on an ODay 25. It was a fine motor for that boat, electric start,
Does anyone have a rudder they bought from Rudder Craft
pgandw at 2:17pm 05.23.24
I have a Ruddercraft rudder on my 19ft Mariner, bought by the previous owner. I love it, especially
Anyone have winch handle pockets on their 315?   (1)
Calif. Ted at 2:16pm 05.23.24
I have a snap it holder also, with a stainless suncor mount on it, I've come to only use the Lewmar
anchoring Hunter 37.5 Legend
flightlead404 at 2:07pm 05.23.24
I am researching different ways of handling the anchor line. The Hunter 37.5 has a very shallow anc
Outdated Flares of All Types.....
thinwater at 12:57pm 05.23.24
I don't think anyone is suggesting that electronic flares replace aerial flares. They replace hand-h
Electric Head conversion
Peggie Hall HeadMistress at 12:39pm 05.23.24
If flushes are getting there from your Jabsco manual, they should make it from the Raritan with ext

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.