| 
	friesen
  		at 6:58am 12.02.17 
 7/925 
	Hi everyone I am planning to install a deckwash pump on a 2007 B40.   Based on various websites I ha
 | ||
| 
	Dan_Y
  		at 5:33am 12.02.17 
 16/1149 
	If you have a few hours or more to burn, go to https://historicalcharts.noaa.gov NOAA's nautical cha
 | ||
| 
	thinwater
  		at 9:28pm 12.01.17 
 12/3209 
	For those with pressurized systems, there are a wide variety of home and RV systems that can remove 
 | ||
| 
	dakno
  		at 9:15pm 12.01.17 
 13/1837 
	Hello sailors I am interested in converting one of my cabin top winches to electric. Have any of you
 | ||
| 
	wyctoronto
  		at 6:26pm 12.01.17 
 6/1368 | ||
| 
	sr1029
  		at 5:17pm 12.01.17 
 6/1130 
	Irma set it aground, didn't take on any water. Have lots of stuff. You want it, I prob got it.  904 
 | ||
| 
	kclancy
  		at 4:00pm 12.01.17 
 15/4514 
	Hi All, I'm having trouble removing the mast step.  The bolts come out fine, but it is also glued to
 | ||
| 
	Syversens
  		at 2:18pm 12.01.17 
 5/782 
	Hey all, this summer one of my chain plate deck fittings (not sure what else to call it) for the sta
 | ||
| 
	Syversens
  		at 2:08pm 12.01.17 
 14/2034 
	Hey all, so I noticed last serious rain storm that there was a leak in the roof under the laminate w
 | ||
| 
	Darin Stubbs
  		at 1:42pm 12.01.17 
 5/1300 
	So, I'm still looking for that perfect or at least as close to perfect Mac 26M to buy.  I found one 
 | ||
| 
	dcstrng
  		at 12:32pm 12.01.17 
 14/3763 
	We recently purchased an otherwise pleasantly clean ODay-30 that almost immediately revealed a leak 
 | ||
| 
	MitchK
  		at 11:29am 12.01.17 
 2/936 
	All,     I have been trying to eliminate or at least minimize water leakage into my N28-2. One of th
 | ||
| 
	MitchK
  		at 11:03am 12.01.17 
 17/4505 
	All,        I am getting ready to install a new bilge pump in my N28-2. I will be installing a Rule 
 | ||
| 
	CYQK
  		at 9:59am 12.01.17 
 12/2277 
	Did navtec go under??  Anyone got the story????
 | ||
| 
	Simon Sexton
  		at 8:22am 12.01.17 
 31/1710 
	What is this...? :laugh:    http://smallcraftadvisor.com/our-blog/wp-content/uploads/2015/08/GravesC
 | ||
| 
	Volkswatson
  		at 7:30pm 11.30.17 
 9/1629 
	I am looking for an image or diagram of a split backstay for a Hunter 23. I'm having trouble figurin
 | ||
| 
	Mark Maulden
  		at 7:26pm 11.30.17 
 3/1442 
	I just repowered with a Beta 35 and the Seaprop saildrive.  I decided to see what it takes to change
 | ||
| 
	Bill19233
  		at 6:48pm 11.30.17 
 15/1671 
	A friend and I are racing my Hunter 340 in the GBCA Chili Chase Regatta this Saturday, December 2nd.
 | ||
| 
	Sumner
  		at 5:39pm 11.30.17 
 32/3303 
	We were looking for an option for good communication between the helm and the bow of the Endeavour a
 | ||
| 
	VanIslandGuy
  		at 2:26pm 11.30.17 
 13/3113 
	I know that the davit issue gets discussed a lot.  Please bear with me...This discussion would mostl
 | 
| 
373 Shallow Draft Depth gurn5877 at 9:00am 07.02.24 There are three draft options available for the beneteau 373 4'9" 4'11" and 6'1" | ||
| 
Boom Vang obstructs Main Sheet JoeWhite at 8:00am 07.02.24 The van block does not need to be so high near the boom. Make a 12" pendant using steel cable and dr | ||
| 
Boom Vang obstructs Main Sheet    (1) kloudie1 at 7:41am 07.02.24 David sailor is right.. it'd be a good test to run to the lower turning block (behind the vang cleat | ||
| 
Invest 95L JamesG161 at 7:06am 07.02.24 Oh My Gosh! that buoy . normally updates every TEN minutes. Now offline for 2 hours :yikes::yikes | ||
| 
Hatch Replacement - 2004 Hunter 31 - lots of questions and help needed Boiler at 6:53am 07.02.24 How did it turn out? | ||
| 
Engine & Genset Pan are they connected ? Boiler at 6:43am 07.02.24 I would place a diaper (oil absorbent mat) under the main to catch anything coming off the engine. | ||
| 
Seeking Sailboat Recommendations for Lakeside Launch Project_Mayhem at 6:13am 07.02.24 I'd go for a 420 over most of these boats as you're not going to get bored with it as easily. Much f | ||
| 
No more vroom vroom? Project_Mayhem at 6:07am 07.02.24 Engine is still in pieces but I did manage to find a used carb. Next up will be to put the motor bac | ||
| 
Stripped screws in plastic NYSail at 5:38am 07.02.24 If the sender is round (most are) can't you just rotate it and drill new holes? Easy. That actu | ||
| 
3gm30f injection pump rack control stuck Fedor Aredakov at 5:18am 07.02.24 Eventually I managed to remove it. It was 128170-51101 PLUNGER W/BARREL broken. Have no idea how it | ||
| 
Stress cracks in Stainless Steel Arch on my Hunter 306 JamesG161 at 4:59am 07.02.24 That is a stress crack , rare to happen unless Oxygen is starved from the Stainless Steel. That is | ||
| 
Stress cracks in Stainless Steel Arch on my Hunter 306 Brinky63 at 4:51am 07.02.24 Thanks for the feedback. Already in talks with welder(s) on island. The arch was never covered with |