Serving sailors online since 1997
 
 

Recent Topics

Kevin at 8:47am 03.07.01
3/1330
I want to clean out/ clean up the fairing on my hull keel joint. What ever compound is in there now
Kevin at 8:35am 03.07.01
0/1120
Reading the posting I saw a bunch of great questions I can't wait for the answers my self....But I c
Bill Jones at 7:30am 03.07.01
2/1108
I have a 1996 H23.5 which I purchased new. Other than the %!#?* trailer, the part of the boat that
Rudi at 7:08am 03.07.01
2/800
According to the Hunter specs, the P42 (Yanmar) should have a 18X14 3-blade prop. I have a 3-blade
Dan Ulrich at 6:45am 03.07.01
1/1038
AL: Do you manufacture a rudder for a 1986 Hunter 23. If so , how do I go about getting info on same
Thomas Ehmke at 6:27am 03.07.01
4/1348
Al, Two years ago while I was sailing on Lake Erie the lower pintle on my 272 broke and before I got
John Richard at 6:19am 03.07.01
3/877
I would like to know what length and size of preventer to have for my cruising spinnaker.
Mike Ross at 6:11am 03.07.01
9/1716
I have a 1986 H-34. Last spring prior to launching I noticed a bulge on one side of the rudder. It
bob uhl at 5:52am 03.07.01
2/1098
I own a Rhodes 19. I'm looking for a picture or drawing on how to rig this boat. The boat was buil
Jesse Tate at 5:18am 03.07.01
6/2868
What is the difference between the Oday 272 and 272 LE? Thanks, Jesse Tate
Andy Howard at 3:04am 03.07.01
5/1079
Our 1984, 34' with the Yanmar 3ghf, has a 15x12 rh 2 blade, Specs call for a 15x15. Checking the arc
Don at 2:54am 03.07.01
15/1063
Weekend project is to repack the shaft on my new (to me) '93 37.5. Boat is in the water and, as I h
John Allison at 2:39am 03.07.01
6/1188
I own a 1979 Hunter 25ft using a 9.9 Mercury outboard for auxilliary power. I have no trouble attai
RANDY CAIRY at 2:07am 03.07.01
1/1048
I am planning to truck my 1990 35.5 hunter and the trucker needs to know the width of the wing keel.
Scott Davis at 2:01am 03.07.01
0/1084
Racing starts in a few weeks. Not much going on now. Have any of you guys found the web page: "Sa
Frederik at 1:40am 03.07.01
1/1478
1)Is there a (preferably)manual windlass for the C30MK III which is made /or fitted for the C30MKIII
Alan Long at 1:29am 03.07.01
4/929
I've been following the discussion about replacing the clam cleats on 23.5/240 with rope clutches.
Marcus Hart at 12:31am 03.07.01
8/1225
I recently purchased a '78 H27. The traveler is in the cockpit. I have seen many pictures of other
Bruce Stone at 12:03am 03.07.01
2/1106
The 310 comes with only a single wooden handhold mounted on the plywood partition on the port side n
Joe at 10:19pm 03.06.01
1/1209
Catalina sells lag bolts for this purpose. They are about 1/2" x 1 foot long and stainless steel. I

Recent Replies

Rainwater Leaks into Portside Cabin compartment
jssailem at 6:41am 04.05.20
Water is insidious in its way to enter our boats. Pictures of the deck above your boat in the area m
Rainwater Leaks into Portside Cabin compartment
CrispyCringle at 6:40am 04.05.20
Anchor locker drain fitting?
Self Isolation
jssailem at 6:26am 04.05.20
D. I think your concern for down stream outcomes is valid. We will have to change. Throughout the c
Hunter 410 refrigerator
sailor420 at 6:20am 04.05.20
Don, did that about 10 years for same reasons. Closed up the spillover hole and installed the smalle
Self Isolation
Flyingnut40 at 6:09am 04.05.20
Ya, BOOMER REVENGE sounds good to me! But I do worry about how THEIR grandchildren will pay for the
SHOULD I sail this season?
Jim26m at 5:59am 04.05.20
This reminds me of the philosophy exercises in College. Let me pose the question from a different
Sanitation hose layout diagram
Scott T-Bird at 5:56am 04.05.20
I am talking about a standard y-valve. My only concern was holding tank air backflowing thru the ve
Recommend me an honest broker in T.O.?
DArcy at 5:52am 04.05.20
You could try United City Yachts. I contacted a few brokers when I was looking to buy over the last
Hello all
ShotgunSlim at 5:43am 04.05.20
Congratulations on your 2 new to you boats! The first run in I ever had with Orb spiders was the da
Ways to stop a Hunter from hunting while at anchor in a blow.
shemandr at 5:23am 04.05.20
The riding sail dampened the velocity of the swinging but the boat swung as far - for me. It didn't
SS U-Mixing Elbow
kappykaplan at 4:57am 04.05.20
Hello, for the engine model it is a yanmar 3JH2E, like on all H380 I think. For the photos, they are
SS U-Mixing Elbow   (4)
GALIOSTRO at 4:34am 04.05.20
SHOULD I sail this season?   (1)
TomY at 4:26am 04.05.20
As I find myself endeavouring to both digest and then implement in a reasoned way the constantly ev
Ways to stop a Hunter from hunting while at anchor in a blow.
Slipin Away at 2:12am 04.05.20
A nylon line bridle attached to the chain and bow cleats help
Sanitation hose layout diagram
Ron20324 at 12:44am 04.05.20
I read it differently, but then again, it is 0345 EDT. The OP says "directional valve", so I think h
ADDING ROLLER FURLING!
garymalmgren at 12:27am 04.05.20
Hi Cas I am sure you are aware that you will need a new sail to go with the furler. Figure that int
Its funny Friday!
jssailem at 10:21pm 04.04.20
Leo you scoundral.:laugh:
SHOULD I sail this season?
jssailem at 10:13pm 04.04.20
the moral dilemma. This reminds me of the philosophy exercises in College. Let me pose the quest
SHOULD I sail this season?
Hunter216 at 9:32pm 04.04.20
Interesting food for thought. Posted by a knowledgeable medical professional 10100252201408846

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.