jviss
at 7:26am 09.02.19
36/2653
The only filter I have on my fresh water system is the screen at the tank manifold, before the pump;
|
||
Isolating Taps? (1)
stephen_i_w
at 7:15am 09.02.19
6/834
On my new 315, just forward of the engine, under the cabin sole are these, each labeled "isolating t
|
||
Harveybutler
at 5:25am 09.02.19
3/429
HAS ANYONE HAD TO REBUILD THE TILLER HANDLE FOR A HUNTER 23.5..
|
||
kiwibyron
at 12:48am 09.02.19
18/3075
Hi all, I recently bought a boat (my first mistake i know...). It's a small dinghy, 2.7m long and
|
||
agprice22
at 6:52pm 09.01.19
2/6972
Upstate New York has been unusually cool at the end of Summer. Our temps are low-to-mid 70s in the d
|
||
IH82BL8
at 6:37pm 09.01.19
8/2989
Is this an option? Isn't PVC pipe impervious absorbing odors? Thanks
|
||
Caspurr
at 6:18pm 09.01.19
6/669
I have a 2007 Hunter 33. Today I turned the key and the engine did not turn over. Batteries are abou
|
||
Mr Fox
at 6:10pm 09.01.19
17/2145
Hi all- looking for some advice on clearing a line from my raritan sea era to my holding tank, which
|
||
glandry924
at 5:39pm 09.01.19
1/395
My '93 Legend 37.5, recently surveyed for a pending sale, had dull tones from the sounding mallet an
|
||
agprice22
at 5:20pm 09.01.19
3/567
Today was a treat! We got a rare SSE blow of 15-20 knots for 3 hours. Being at the South end of Sene
|
||
Tim22
at 3:49pm 09.01.19
4/524
I recently installed a V1 windlass and for the most part am happy with it. What I do find irritating
|
||
drcov
at 3:05pm 09.01.19
6/959
I just pulled the old worn out water heater. Should I replace or just forget it. I have a marine uni
|
||
pumpkinpie
at 1:39pm 09.01.19
10/1820
.
|
||
pumpkinpie
at 1:05pm 09.01.19
5/898
.
|
||
Cowpokee
at 10:44am 09.01.19
8/1329
When planning out our three day weekend, my wife asked about the possibility of sailing. I desponden
|
||
fero
at 10:08am 09.01.19
4/501
Hi again, Last time I was on the boat ( before haul out for hurricane season ), I tried to run the f
|
||
DayDreamer41
at 8:56am 09.01.19
7/525
Yesterday during a race in light air <8 on the first down wind leg (wind at our starboard quarter) w
|
||
cbourne200
at 7:30am 09.01.19
12/1162
Ok. Need to replace water temp guage in panel. Unscrewed it and it fell into 2 pieces. Break is vert
|
||
For Sail
at 7:07am 09.01.19
0/292
My port sheet winch is locked up. It is a Maxwell 17c. I took it apart cleaned everything, regreas
|
||
ZeusRod
at 6:23am 09.01.19
5/783
Hello All, Taking off the forestay chain plate where there was some damage to the deck and the bolts
|
Yanmar KM2A un-serviceable? Also need transmission basics too.
Tally Ho at 4:20pm 09.26.23 Should be no reason you cannot unbolt the transmission from the engine and replace it with a rebuilt |
||
The Sewing Machine Thread
Tally Ho at 4:08pm 09.26.23 Does that machine have a walking foot? dj No walking foot. You can buy an attachment, but it is |
||
Just a bit too much heel and helm
danstanford at 4:05pm 09.26.23 Like I said-they are better sailors. This was right after a big gust and I dumped the main but hadn |
||
Ruddercraft Lower Pintle Failure
Any Sea at 2:50pm 09.26.23 I ordered a spare lower pintle to keep on the boat in the tool bag. I'd rather be looking at it tha |
||
Ruddercraft Lower Pintle Failure
Rltgold at 1:57pm 09.26.23 I just got off the phone with Jeff . We had a very nice conversation about the Pintle issue. It is n |
||
Raymarine RL70C..... (1)
Rich Stidger at 1:40pm 09.26.23 I am not sure what a "L750" is, but here is the connections for a RL70C display. I might have a con |
||
Ruddercraft Lower Pintle Failure
RudderCraft at 1:24pm 09.26.23 Hello all Catalina 22 owners. My name is Jason and I am the owner of Rudder Craft. I am also a proud |
||
Raymarine RL70C..... (1)
RitSim at 1:06pm 09.26.23 I also have an L750 that I am working on. Can you tell me which pins are power and ground? |
||
My solution for winch override. Yours? (3)
thinwater at 12:28pm 09.26.23 Some examples for discussion. Some of these I know to be stock installations. https://forums.sailboa |
||
My solution for winch override. Yours?
thinwater at 12:22pm 09.26.23 ... Then the rotating cleats serve me much better.... I need to think on that. On one hand, I u |
||
My solution for winch override. Yours?
thinwater at 12:09pm 09.26.23 Plus a million to the tiller lock comment. I use the TillerClutch device and frankly don't see how |
||
Rudder Craft Rudders
Timm R Oday25 at 12:02pm 09.26.23 I use 80/20 during the course of my job. I have lot's of it from previous projects that my employer |
||
Ruddercraft Lower Pintle Failure
Rltgold at 11:45am 09.26.23 This is specifically forRudder Craft Brand systems. They have said most issues were with 3/8" Pintle |
||
Ruddercraft Lower Pintle Failure
AaronD at 11:37am 09.26.23 Are these failures on the early boats and the MK II boats? Those with actual experience may correc |
||
Ruddercraft Lower Pintle Failure
Rltgold at 11:34am 09.26.23 Any Sea, Possibly additional brackets with bolt/locknut or castellated nut with cotter pin. I had |