Serving sailors online since 1997
 
 

Recent Topics

Gene Fink at 3:29am 10.17.01
2/2447
I would like to find more information on how many Capri 30s were built. My boat is a 1983. Where can
Jeff at 3:13pm 10.21.01
1/1314
I have a '90 Hunter 28. About a year ago I replaced the entire manual pump and it worked fine. The p
Robert Dean at 5:49am 10.15.01
1/1966
Don, When I race I usually do so with a whisker pole wing/wing setup going downwild. If I had the ab
henry at 1:12pm 10.21.01
1/879
I'm looking for a exhaust flap for my 30' Catalina. Can anyone direct me to a Catalina parts distrib
Chris at 11:45am 10.21.01
0/723
I'm hoping someone out there will know where I can find used parts for a Universal M-15 (5411)in So
Owen Trepanier at 5:13am 10.15.01
4/1387
I noticed the I-beam between my keel and compression post is sort of delaminating (if steel can do t
Dick of Sylvan at 11:01am 10.21.01
5/1703
I have a 98 Chev. Silvarado Pickup w/ext. cab and only two wheel drive and the original General high
Frank Walker at 8:54am 10.21.01
1/964
I am interested in adding a ST60 close hauled indicator to my ST60 suite of instruments, but I worry
Jim Remensnyder at 4:53am 10.15.01
3/901
Will the stock engine mount on a 1988 Hunter 26.5 hold the weight and size of a 4 cycle Honda 8hp or
Dic Kavalauskas at 7:00am 10.21.01
4/1021
I recently sold my Catalin 25 and I'm considering purchasing a 1998 C320. The boat is located in the
donald gibbons at 4:27am 10.21.01
0/945
54' Hunter, I just purchased the boat. The beam of the cabin below the mast has been shrinking as
Larry W. at 4:21am 10.15.01
1/995
Bill; The wind pointer on top of the mast was broken by a big bird and West Marine can't get a new o
WALLACE SHAKUN at 12:20am 10.21.01
3/1072
ON A 380 WITH A BULB KEEL WHAT SHOULD THE DEPTH OFFSET BE SET (CALIBRATION)
Rick at 11:24pm 10.20.01
2/1565
Just bought another project boat, a 1980 US 25 made by Bayliner. Anybody out there with an owners m
John Visser at 2:51am 10.15.01
3/1209
What is HSB2? Is it compatible with older HSB stuff?
Jim H SR at 9:08pm 10.20.01
2/1305
Thanx Rob R, Austin Tx for the info. provided. Now, anyone else out there know about or used this p
John Richard at 12:38pm 10.20.01
4/872
I just got back from the Long Beach, CA boat show. I got to go thru the new 356. It is really a ni
Chuck at 2:18am 10.15.01
3/1939
Has anybody had experiance with a company called Sailcare and there LaMauney reconditioning process.
Clayton Wright at 10:23am 10.20.01
3/1208
I am considering purchasing a 1973 Oday 23, and am concerned that it is too big for practical single
Frank at 10:01am 10.20.01
0/746
Looking for a 1981 HUNTER 25' Owners Manual The one I brought from Hunter was less than Desirable b

Recent Replies

Varnishing with urethane
jaysweet at 5:48pm 05.16.20
I'm mostly ignorant on the subject, so let me ask: how is the term "varnish" not just a generic term
Diesel fuel leak
smokey73 at 5:44pm 05.16.20
That would work. It might be a good idea to do both. Pressurize the line first from the fuel filte
PVC Tube in 340 Mast
looking2buy at 5:43pm 05.16.20
I got the sail to the top of the mast... a little harder than would have expected/liked but it raise
Temp range?
JK_Boston_Catalina310 at 5:37pm 05.16.20
I haven't seen this mentioned. Here is how I assess heat issues on Smitty. https://marinehowto.com
Rub Rail Adventure   (2)
jaysweet at 5:29pm 05.16.20
Anyway, in searching this forum, I hadn't found any really clear explanation of what was involved in
Big time decision.
capta at 5:27pm 05.16.20
First, what genset is it? We removed ours a couple of years back and replaced the engine and had the
Transmission problems yanmar 2gm20f with km2a
Fashin at 5:22pm 05.16.20
So it is possible that the water got in there over time and no service has been done by the previous
Nominal Spar Wall Thickness
JamesG161 at 5:20pm 05.16.20
My last point... Stainless self tappers in an Aluminum mast will not set up galvanic corrosion, if t
Rub Rail Adventure   (2)
jaysweet at 5:19pm 05.16.20
Surprisingly, I actually managed to extract 2 screws, but they were the little ones that secure the
Varnishing with urethane
All U Get at 5:16pm 05.16.20
I agree with Dave, let me offer my boat as a good practice area.
Diesel fuel leak
capta at 5:12pm 05.16.20
How can you pressurize the tank if it has a static vent? I am assuming you are meaning close the f
Diesel fuel leak
smokey73 at 5:10pm 05.16.20
Do you have an aluminum tank? I had pinhole leaks and thin spots in the bottom of the tank and it w
Nominal Spar Wall Thickness
JamesG161 at 5:10pm 05.16.20
By the way.. @Brian D the fore part of your mast should have a cable conduit or the like, in that
high water?
jon hansen at 5:07pm 05.16.20
TLWS19ypNy8
high water?
jon hansen at 5:04pm 05.16.20
i hate fog
high water?
jon hansen at 5:03pm 05.16.20
InxQlUOYAng
high water?
jon hansen at 5:03pm 05.16.20
E9jlBF00w4w
Nominal Spar Wall Thickness
JamesG161 at 4:56pm 05.16.20
ok guess what I had to do... Steaming/Deck Light Combo I used was going to use short self tappers t
Diesel fuel leak
smokey73 at 4:56pm 05.16.20
Simplest way to find a fuel leak is to pressurize the line. Take the suction line off the filter t

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.