chet pruszynski
at 11:37am 10.23.01
2/1323
I am about to replace my GROCO (HC or HE not sure ) "leaker" with something a bit more upscale. the
|
||
Greg aboard 'BlueBerry'
at 8:37am 10.23.01
4/1041
Although I do not need it right away, I know I will in the future. Can anyone measure (or tell me w
|
||
George
at 6:14am 10.23.01
4/1035
I am thinking about installing a new set of instruments in the '76 C27 we just got and are restoring
|
||
Alan Lynn
at 5:56am 10.23.01
6/1105
I let the rope loose for my keel and it never dropped all the way. Tried muscle, jiggling, pulling
|
||
Chuck Defever
at 4:52am 10.23.01
4/911
Am considering an st4000 and owner instalation for hunter 336. Does the standard console/pedestal h
|
||
Michael McCann
at 3:37am 10.23.01
4/1384
Bill;A friend's ST50, and mine are approximately the same age (new in 1992/1993). His temperature r
|
||
Dave Mauney
at 3:33am 10.23.01
5/1209
I am just getting ready to refinish my brightwork. I am wondering if it is possible to leave the ma
|
||
Don curt
at 2:52am 10.23.01
0/849
I was doing a little repair on my 336 compression post area at the deck to keep a very minor drip ou
|
||
Ron Newton
at 1:50am 10.23.01
1/1054
I'm thinking of buying an O-Day 27 It has some blisters on the bottom. Could anyone out there give m
|
||
Ed Schenck
at 1:16am 10.23.01
3/943
Hi Phil, I did get your e-mail regarding the refresh problem but never followed up. The reason is
|
||
Mike
at 11:13pm 10.22.01
1/2113
The main sheet on my O'day 23 is attached to the cap at the end of the boom. A large bolt is affixe
|
||
Carlos J. Rivera
at 5:29pm 10.22.01
1/865
I'm planning to buy a Huntern27' 1985-88 by next year. can this boat w/ the proper equipment/gear t
|
||
David Undewood
at 12:31pm 10.22.01
7/1113
I have a 1982 Hunter 33, and I am ready to install a small microwave oven. I have an idea that over
|
||
jeff
at 11:56am 10.22.01
4/912
i tried to use the quick reef system on my 88 cat22 yesterday. i released the boom vang, the down h
|
||
Mal Trotter
at 11:42am 10.22.01
4/916
I have a 1997 340. I am finding that engine coolant is leaking from the overflow tank in small amoun
|
||
Rob Welling
at 11:38am 10.22.01
1/990
I have all but decided that a Hunter 37C will be my next boat. I currently own a Classic Charlie Mor
|
||
Pat Reynolds
at 11:25am 10.22.01
2/939
I know this is probably a question that has been asked over and over but...What is the definitive te
|
||
Chuck Kretschmar
at 10:30am 10.22.01
8/1034
I have 1988 Cataline 30, Tall Rig, which I sail on Lake Texoma. While the lake remains "flat" even i
|
||
Chuck
at 9:59am 10.22.01
3/852
I just purchased a Cat 30 and am new to ownership. As the boat was hauled out of the water, I notic
|
||
Rick
at 9:50am 10.22.01
7/1228
I have thought for five years, I would rig my hotwater heater so I could drain her instead of pumpin
|
2008 Hunter 33 Anode Replacement
jaysweet at 6:02pm 05.17.20 Yes, I do mean the zinc anode to clamp to my prop shaft. I tried a 1 inch and it was a tad too sma |
||
Yanmar 2GM20F: please criticize my plan!
BigEasy at 5:52pm 05.17.20 Go for it! Looks like a good plan. All of the remaining engine work can be done in your slip. |
||
PVC Tube in 340 Mast
jssailem at 5:51pm 05.17.20 Do you have a "Topping Lift and a Jib halyard? You do not want to trust the Main Halyard to get to |
||
F*!$#ing Scupper hoses
ontherocks83 at 5:36pm 05.17.20 The bruises and cuts on your forearms from that job are no joke, I was telling someone that after I |
||
F*!$#ing Scupper hoses
doublebuffle at 5:30pm 05.17.20 My transom looks about the same. I just pulled the exhaust hose out to replace the through-hull with |
||
Fixed Portlight replacement on Passage 42
eianm at 5:25pm 05.17.20 i just removed one yesterday to re seal it and they are a lot more than a piece of cut perspex! Ther |
||
2008 Hunter 33 Anode Replacement
amitchell64 at 5:22pm 05.17.20 Sorry: do you mean what size of zinc to clamp to your prop shaft? (Or do you mean a protective anod |
||
Clean up on aisle 5: how to clean up old cleats
jaysweet at 5:17pm 05.17.20 "I'm not a smart man": Forest Gump. But if I were, I would have learned by now that you never post |
||
Diesel fuel leak
Hydro Therapy at 5:14pm 05.17.20 My Westerbeke was leaking fuel around the area of the tranny. The lift pump was the culprit. Rust cr |
||
Perko raw water filter
justsomeguy at 5:08pm 05.17.20 Have you tried a bit of oil/penetrant, tapping the joint, another drop of oil and then time? |
||
merc 9.9 outboard on my 260- help please
gudiss at 5:05pm 05.17.20 andy, thank you very much!! that should do it- |
||
R20 Outboard length? (2)
AndyVS at 4:38pm 05.17.20 Here are a couple of pics of my 9.9 on my Mac26C. I slip on a small inland lake and rarely lower the |
||
Stuck throttle? (15hp Chrysler/Johnson)
sbcwolff at 4:35pm 05.17.20 Going to try and clean carb and start again... maybe when it is running and not quitting we can put |
||
Small cracks in Hunter 28.5 fresh water tank
Hello Below at 4:23pm 05.17.20 Mike, I have only general information for you that I found. You can put epoxy on gelcoat (polyester |
||
Clean up on aisle 5: how to clean up old cleats
thinwater at 4:00pm 05.17.20 Oh no. You really should not have shown us the snap-lock.... A whole new thread on crimp vs. solder |