pat
at 1:07pm 01.13.02
4/1089
Hello. I'm looking for a sailboat to purchase, and I'm seriously considering an older Catalina 30. T
|
||
doug
at 12:35pm 01.13.02
0/762
Just wandering
|
||
Jonny Quest
at 3:36am 01.05.02
3/856
All,Good afternoon. I would like to have the steering wheel of my Hunter covered in leather. I w
|
||
Dave
at 11:26am 01.13.02
1/919
I am looking for any info or suggestions on sailing around the Plantation Key area in South Florida.
|
||
Tom
at 10:58am 01.13.02
5/2499
I am speaking of the pencil zincs in the engine heat Exchanger....(BTW I have a Universal M35B)1)
|
||
kirk
at 1:52am 01.05.02
3/1140
We are looking for replacement cushions for our 1995 29.5. Any ideas? Have a Happy New Year!
|
||
George Leitner
at 5:21pm 01.27.02
3/834
With my hunter 310 I also sometimes feel, that 18 Hp is not enough. Does the change from a 2 blade p
|
||
Jack
at 1:31am 01.05.02
17/1197
Opinions please. There have many questions about redoing decks lately. My question is whether or not
|
||
Michael O'
at 1:25pm 01.27.02
3/848
I'm about to fix a compression post problem on my H-31.It occurs to me that this is the perfect oppo
|
||
mike
at 7:45am 01.13.02
6/878
I've lowered my bunks to work on them and the bottom of my boat. Now as I put them back up I'm wond
|
||
Ed Dunar
at 12:29pm 01.27.02
2/1155
A while back I remember seeing a site about a group cruise from VA? to Bermuda burt cannot seem to f
|
||
Anton Wilson
at 11:15am 01.27.02
14/1909
I've read the questions and responses to portable gennis.. My situation is as follows.I am heading
|
||
Ted Friend
at 6:30am 01.13.02
14/890
Hi,I just purchased a 260 and am shopping for an engine. I am looking at the Mercury 9.9 Sailpowe
|
||
Peter
at 8:39am 01.27.02
0/951
I see there is quite a thread on how to raise the rudder on a 23.5. Try this method - it works for
|
||
Bert Kinyon
at 12:38pm 01.04.02
0/765
I've noticed some small cracks traveling running along under both sides of the sliding top cover of
|
||
Lambert
at 6:38am 01.27.02
11/1284
Take a look at my 20 pictures of my Hunter 34 1983 in big renovation, at the photo forum, and tell m
|
||
Tom
at 4:07am 01.13.02
0/1879
I am looking for the manual for a Regency Polaris VHF radio(model MT5500XL). If anyone can forward a
|
||
Lambert
at 3:02am 01.27.02
0/824
I bought the boat 2 years ago, I am completely re-doing the boat, ext int. spent 30000$ on renovati
|
||
Duane
at 1:14am 01.27.02
0/961
Does anyone know if dimensional line drawings or construction drawings are available for a Catalina
|
||
Jeff
at 2:43am 01.13.02
1/1050
What is the brand of the rangehood/fan unit in the 470 galley and how good is it?
|
C30 Rudder Removal (3)
doublebuffle at 10:02am 03.01.20 I drilled and tapped holes to press out the cap. I left the rudder to hang to add some additional do |
||
Yanmar 2GM starting trouble
Ted at 9:21am 03.01.20 Make sure your stop cable isn't binding in the closed (off) position. |
||
Anyone else following the Sail GP series this year?
Hunter216 at 9:15am 03.01.20 I found that I started to get adjusted to watching the speed after the first few minutes as the rela |
||
Old Man Going West!!
Scott T-Bird at 8:52am 03.01.20 Agree with you Scott, not finding much at all. Likely I'll find it too cold for me by the time I ge |
||
Strut lubrication?
capta at 8:35am 03.01.20 The set screws keep the bearing/bushing in place which in the strut, with my wakeboard boat, was c |
||
hit a rock in the keel
CrispyCringle at 8:35am 03.01.20 Steel is "of Iron". To get typical steel you mix in a little carbon with the iron. Cost more, but st |
||
hit a rock in the keel
Kings Gambit at 8:32am 03.01.20 OK. Cast iron is an alloy of iron and carbon, w/ between 2 and 4% carbon; whereas, steel is an alloy |
||
Old Man Going West!!
Scott T-Bird at 8:15am 03.01.20 Get along little doggie? Technically, I think its dogies , but I'm going to believe that it is spe |
||
Twisting a fitting on tank (2)
Bob S at 8:04am 03.01.20 Greg, I found it easier to just order the Uniseals and press in new fittings. I also enlarged the ve |
||
CNG tanks
sail sfbay at 7:47am 03.01.20 Suggest contacting a local welding supplier like: https://www.globalwelding.ca http://www.camcarb.c |
||
Big scare with new standing rigging (1)
Roadking Larry at 7:35am 03.01.20 I used a Canon SX50 bridge camera with a 1200 mm zoom to get those shots, and digitally cropped the |
||
Yanmar 2GM starting trouble
coolair at 6:56am 03.01.20 Thanks for the replies. I reviewed the Yanmar manual to find the bleed at high pressure pump. Will |
||
Yanmar 2GM starting trouble
coolair at 6:15am 03.01.20 Mermike. I did not bleed from the high pressure pump. I just loosened the fuel lines at the inject |
||
Catalina 315 specifications
Alansails at 6:07am 03.01.20 The 310/315 Association was grouped by Catalina a couple of years ago, we had no say so. It is nice |
||
Refrigeration - My big off season project
Justin_NSA at 6:03am 03.01.20 Didn't get much help from Nova Kool on recharging my unit. Evidently my BD2,5 compressor has been su |