Serving sailors online since 1997
 
 

Recent Topics

Tom McCreary at 1:11am 06.01.02
1/2242
Looking for advise as to how to free up a rusty pivot pin. Just bought this boat, it's my first.
Michael at 1:04am 06.01.02
3/1156
Could anyone please let me know where I can rent a cruising sail vessel in the Marathon area? I will
Michael at 12:58am 06.01.02
1/1043
Good day all. I will be in the Baltimore/Annapolis area 6/2 - 6/5 on a medical conference. The wonde
Carl at 12:39am 06.01.02
8/1093
I have a roller furler but do not have uv tape on the jib.Is this somthing I can add myself or do I
George Chamberlain at 12:34am 06.01.02
7/2838
First, thanks to Rich for the copy of the O'Day 22 manual. After receiving your email, I dug thru m
Terry Cox at 11:53pm 05.31.02
0/690
In previous articles I had inquired for help in diagnosing my forward cabin heat pump problem. Thank
john anderson at 11:50pm 05.31.02
7/1023
On my 376 I have two small expensive! aluminum tanks made in 1997 that now have to be fitted with an
Greg at 10:00pm 05.31.02
4/773
Hey Peter, I noticed you were back... you must of had some serious blister damage. Hopefully you go
Jim WIllis at 9:18pm 05.31.02
2/997
We had this discussion before, about chlorox eating stainless welds etc. Anyhow, I had this mysterio
Joe Mullee at 9:09pm 05.31.02
4/1078
I need suggestions on where I can get a good first aid kit? I do most of my sailing on the Chesapeak
Steve at 10:56am 05.31.02
1/1288
I am looking for an owners manual for my 1974 macgregor venture and some place that I can buy parts
Dan F at 9:58am 05.31.02
3/854
I have a '79 CAT 22, and I know it is not the fastest boat on the water, but when other Catalinas an
Jim Bessinger at 9:29am 05.31.02
5/1993
I keep reading about poli-glow, however I don't see it listed in Boat U S or West Marine or in the c
Art Eskowitz at 8:36am 05.31.02
6/1662
Has anyone had any experience or problems with Dinghy Davits on a 98 376.If experience was positive
Joe M. at 8:00am 05.31.02
5/5055
I am a casual racer of an older H30. My question is can you furl a Mylar sail? - I am getting confli
Bob at 7:54am 05.31.02
3/956
I own a 1991 Hunter 28 which came equipped with an 18 hp Yanmar motor. I notice that when I back th
Mike at 7:49am 05.31.02
0/836
Use a step ladder. I have used an extension ladder to go all the way to the spreaders
fred miller at 7:14am 05.31.02
0/935
OK. Maybe I'm dumb but how do the screens fit it. From the outside or inside? Do I have to insert th
Armando at 7:02am 05.31.02
8/852
I have to install speed/depth tansducers on my hunter 23. I'm thinking of installing them at the bot
Fred Miller at 6:53am 05.31.02
4/1074
Like most dodgers, the one on my 35.5 uses two adjustable straps at the rear of the frame to keep it

Recent Replies

How deep to launch
LakeShark at 8:04am 07.30.20
You're extrapolating from one fairly extreme case to the general case. I've personally gone off the
Funny Friday!!!   (1)
Will Gilmore at 7:59am 07.30.20
https://s3.amazonaws.com/lowres.cartoonstock.com/medical-doctor-patient-clean_bill_of_health-health_
Replacement Propane tank for Catalina 310
leo310 at 7:56am 07.30.20
Before you disposed the tank did you look at getting it re-certified as all it is a new safety valve
How deep to launch
Tedd at 7:54am 07.30.20
unfortunately if your trailer falls off the ramp into the hole you will not be able to pull it out
Interior wood trim repair or other ideas
jssailem at 7:54am 07.30.20
Forbin. What caused this to fail? Someone grab it? Push it instead of the dishes? The though of a
Facnor Shackie
sail sfbay at 7:54am 07.30.20
Sounds like a good question for Facnor. R24 refers to the elliptical section on pages 12-13 from th

Marvin "Guy" Royal at 7:52am 07.30.20
I have a Peake tri-radial asymmetrical spinnaker with a CDI top down furler (used once), ATN sock a
How deep to launch
LakeShark at 7:52am 07.30.20
Ready to launch. Fully extended....backed down till she floated off. WOW that's one of the rare ti
Solar Vent on a head hatch.
capta at 7:50am 07.30.20
Capta, Marinco/Nicro calls it a shutoff damper. https://www.marinco.com/en/~/media/inriver/382
How deep to launch
LakeShark at 7:49am 07.30.20
obvious, but sometimes overlooked.....if a kick-up rudder, make sure it is "up". If not a kick-up,
Eractic Tachometer and engine power
capta at 7:46am 07.30.20
There should be a sensor located somewhere on the bell housing of the transmission. Remove the 2 w
dorade box cowl vent
capta at 7:37am 07.30.20
Who cares about the air those dorades provide? They and the rest of the brightwork look fantastic!
Rigging a Capri 165   (1)
Johnfranklin1 at 7:34am 07.30.20
Two answers at once....:)
Rigging a Capri 165
Johnfranklin1 at 7:31am 07.30.20
I think this is the appropriate part. Perhaps contact them to confirm for your specific boat. http
Rigging a Capri 165   (1)
Johnfranklin1 at 7:29am 07.30.20
Maybe I connect the pendant to the vang with this?
Rigging a Capri 165
Hunter216 at 7:28am 07.30.20
I think this is the appropriate part. Perhaps contact them to confirm for your specific boat. https
Rigging a Capri 165
Johnfranklin1 at 7:27am 07.30.20
I would point out the screw is quite loose where a shroud (I think) is attached. mast and on throu
C310/315 IA Membership Pages Updated
Jacksail at 7:25am 07.30.20
thanks Curt.
Rigging a Capri 165
Johnfranklin1 at 7:19am 07.30.20
Thanks Joe, Lets say I want to use a pendant. What is the series of parts in the connection b

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.