Rick Lobalzo
at 9:41pm 04.12.02
1/851
I am trying to get the rudder apart. I've taken the screws out but I can't get the disks and the bol
|
||
Lisa Woodburn
at 2:32pm 04.12.02
7/989
Hi sailors.The Catalina 22 racers I know have joked with me about this - they asked "why do you wa
|
||
Geof
at 1:52pm 04.12.02
5/1215
I am in a quandary. The outlet seacock is frozen. It is a conical brass seacock - vintage '76 prob
|
||
Dave Royce
at 12:21pm 04.12.02
3/806
I have a 1994 23.5 and have been thinking about a bigger boat. I was contacted about a 1988 28.5.
|
||
Marcelo Ferrer
at 10:56am 04.12.02
4/1077
Folks,I just got my first Catalina C27, which by the way is also my first boat, and as one would e
|
||
George
at 10:53am 04.12.02
3/1569
I would like to know if some one out there has any knolage of what years the wing keel was produced
|
||
sw
at 10:28am 04.12.02
1/1102
I have a noise isolated to the general area of the rudder post on my open wire steering system. Anyo
|
||
David H.
at 10:16am 04.12.02
31/1697
Was on the British based site www.ybw.com and the discussion group there really let Luhrs Marine hav
|
||
Mark Fogg
at 10:05am 04.12.02
8/1500
Sailing friends some help please. My 1974 Venture 23 cutter came with a great lookingtrailer. But..
|
||
Jerry
at 8:44am 04.12.02
11/1424
I am looking for some direction regarding a sailboat I purchaed nine months ago. Before buy the boat
|
||
Roberto
at 6:32am 04.12.02
2/978
I am trying to sale my H23 1987. It is in perfect condition. I leave in Texas. Do somebody knows how
|
||
Butch Bowker
at 4:50am 04.12.02
0/1105
I recently purchased the above Davit System and am preparing to install same on my 1986 Hunter 34.
|
||
Eric C Lindstrom
at 4:40am 04.12.02
1/1246
Next month I'm going to have to construct a cockpit mast cradle for our Hunter 30 (to get through th
|
||
Mike Corcoran
at 4:34am 04.12.02
6/998
I'm facing a job transfer from the San Fraancisco Bay to the Chesapeake Bay. I have a 37 cutter wit
|
||
John Berlin
at 4:16am 04.12.02
0/776
I have a 2002 310. My question is about the furling line and how other owners are cleating down the
|
||
Dave
at 3:14am 04.12.02
1/1115
Can anyone provide me the CDI web site address?Thanks,Dave
|
||
jim
at 12:42am 04.12.02
6/1033
Ok,it's getting close to tax deadline and I wonder if there are any "creative" accountants out there
|
||
Dave
at 12:33am 04.12.02
7/1111
I would like advice on whether or not I should replace my wire to rope halyards with all rope or rep
|
||
Brent Stiles
at 12:05am 04.12.02
1/1043
Any suggestion on running lines aft on an '86 capri 18?I'd like to replace the clam cleats on the
|
||
Larry Crippen
at 11:59pm 04.11.02
3/1201
Has anyone had experience with broken turning blocks connected to studs in the cast aluminum mast st
|
Defeating a Catalina 34 design flaw
FastOlson at 12:39pm 03.21.20 Looks quite useful. Most of us that keep our boats for the long term keep adding small (and sometime |
||
Hunter 23 Bimini
knotatwork2 at 12:31pm 03.21.20 Thanks for the picture, where did you get the bimini from |
||
Jib Halyard/Sheet Replacement
FastOlson at 12:31pm 03.21.20 The sail area is not all that much on a Cal 21. (We raced and cruised a Ranger 20 for years...) With |
||
Jib Halyard/Sheet Replacement
Dave Groshong at 12:29pm 03.21.20 We offer both, but you really should change the masthead sheave, it is likely old school wire only |
||
Jib Halyard/Sheet Replacement
EnamrdSalr21 at 12:26pm 03.21.20 Great. Thank you all for the replies! |
||
Jib Halyard/Sheet Replacement
dlochner at 12:22pm 03.21.20 With the sheave that I sent a picture of for the headsail- wouldn't it be to narrow to fit a 3/8" l |
||
Shelf Sheltering?
JamesG161 at 12:19pm 03.21.20 Cheap vodka is not an acceptable substitute I have been joking around about cheap vodka. You can u |
||
Anchor attachment point to rode
jon hansen at 12:10pm 03.21.20 chain on your rode is fine. chain on your rode is great. chain on your rode is A huge pain in the as |
||
Anchor attachment point to rode
jon hansen at 12:05pm 03.21.20 there is zero need for chain on the great lakes. if some person or thing claimed other wise, they or |
||
Jib Halyard/Sheet Replacement
EnamrdSalr21 at 12:02pm 03.21.20 With the sheave that I sent a picture of for the headsail- wouldn't it be to narrow to fit a 3/8" li |
||
What is this on my Keel?
DayDreamer41 at 12:01pm 03.21.20 Looks to me like an adhesion issue, someone along the way used too much faring compound? |
||
Looking exhaust manifold
dlochner at 11:58am 03.21.20 You'll probably have to bite the bullet and visit a Yanmar Dealer. |
||
Jib Halyard/Sheet Replacement
dlochner at 11:54am 03.21.20 Basically the same as turning your underwear inside out to get a few more weeks out of it. That w |
||
Jib Halyard/Sheet Replacement
JohnShannon at 11:43am 03.21.20 Great idea! re of the twisted wire and the part that attaches to the headsail. Basically the same |
||
Jib Halyard/Sheet Replacement
EnamrdSalr21 at 11:41am 03.21.20 Oh, @dlochner not sure if I misunderstood your question. Did you mean you wanted to see the sail it |
||
What is this on my Keel?
captcoho at 11:40am 03.21.20 BTW.... The keel bolts are not bonded to anything in the boat, or ground or any type of lightning pr |
||
Jib Halyard/Sheet Replacement (3)
EnamrdSalr21 at 11:37am 03.21.20 Halyards have areas of high wear, typically on the sheave when the sail is raised and at the cleat |