gtg
at 10:33am 07.07.20
15/5408
Anyone seen someone swing from the mast? I turned a 25 Catalina jib halyard into a swing. I was to
|
||
nautikaljeeper
at 10:11am 07.07.20
8/1452
Interesting article. Would really like to hear some feedback from some great minds. Mainsail? Lithi
|
||
sthorogood
at 6:06am 07.07.20
1/363
I ran over a tree and sheared the blades off my 1995 H29.5 propeller. Have new prop on way from Hun
|
||
jbreland
at 5:36am 07.07.20
7/922
Have a hunter 26 and need to replace the lense (opening part) of the port. They are the Gray enterpr
|
||
rogerschwake
at 7:11pm 07.06.20
17/5794
Just bought a Rob Roy 23' in Florida and pulled it home to Iowa. It is a 1987 build boat with lots o
|
||
Claude L.-Auger
at 7:06pm 07.06.20
3/1161
Hi everyone Have had my 34 for 20 years and today I replaced the plastic Yanmar ignition panel for t
|
||
RPD677
at 7:02pm 07.06.20
10/4359
Hi Everyone, This is my first post and I am relatively new to sailing so pardon my beginner knowled
|
||
Steve L22188
at 6:47pm 07.06.20
0/315
My Navman combo speed/depth display finally shot craps. Sent it off to Tom Stevens (see his YouTub
|
||
Pagan Baby
at 6:44pm 07.06.20
9/932
|
||
Sergey Vetrov
at 6:43pm 07.06.20
2/513
There are three run-outs for water drainage on the deck oh Hunter 38. The problem is that they are
|
||
murrayabbott
at 5:35pm 07.06.20
3/603
Hi everyone, I was out on the boat for the weekend and went in for a pump out. Unfortunately the att
|
||
jonelli
at 5:10pm 07.06.20
22/6582
I know these are generic motors, Tohatsu, Mariner, etc... And I've got the service manual. But, bef
|
||
Halipeno2
at 4:47pm 07.06.20
3/1029
I have a 1995 Hunter 35.5 Legend, I removed the rudder to replace the plastic bushings because they
|
||
murrayabbott
at 4:34pm 07.06.20
5/850
Hi everyone, I was out on the boat for the weekend and went in for a pump out. Unfortunately the att
|
||
MiltonB
at 4:14pm 07.06.20
5/705
I have a Gulf Coast Brand Model 23 I have no idea if it has a swing keel or fixed keel. The only in
|
||
Gary Ballentine
at 4:07pm 07.06.20
10/1426
Looking at replacing the original 42 inch wheel on my Hunter 40.5. Was looking at the Lewmar 42 inc
|
||
calvin
at 3:30pm 07.06.20
1/696
One of my last projects this winter was to install a shore power connector and a new DC panel with d
|
||
rpwillia
at 2:36pm 07.06.20
12/1238
So in commissioning prep this year I replaced my spin on filter and my racor. To make it even crazie
|
||
calvin
at 1:47pm 07.06.20
10/2633
Has anyone put a folding wheel on their 33.5? Am considering doing so on mine and wondering if anyon
|
||
thetone
at 12:53pm 07.06.20
1/694
I have water damage to my companionway steps and dining table. This is my 1990 35s5. Can anyone give
|
Fuel filter size
Stu Jackson at 8:16pm 01.25.25 Fuel Filtration 101 (with both primary Racor and secondary engine filter identification) Fuel Filt |
||
What is this on my boom?
yelkenli at 7:29pm 01.25.25 A track for the reefing clew. Not common, but one of my boats had that. Thanks @thinwater Does a |
||
Runaway diesel
Captain Larry-DH at 7:20pm 01.25.25 Ok thanks gentlemen. Reassuring to know. Startling video. |
||
Fuel filter size
Alan Gomes at 6:44pm 01.25.25 Don't use a 2-micron filter anywhere in the system. It is too hard on the fuel pump. MaineSail had s |
||
What is this on my boom?
PaulK at 6:32pm 01.25.25 Modern reefing lines run through sheaves at the end of the boom, up to the clew of the sail, and the |
||
Fuel filter size
Don S/V ILLusion at 6:05pm 01.25.25 Lots of info on how to size primary and secondary filter size. Primary typically larger than the sec |
||
Fuel filter size
Ralph Johnstone at 5:09pm 01.25.25 Seems the most common arrangement is 10 micron in each filter. My Yanmar guy is an endless fount of |
||
What is this on my boom? (2)
garymalmgren at 4:29pm 01.25.25 Hi yelkenli RE: The topping life comes to a block on the end and from there I am not sure where to |
||
What is this on my boom? (1)
JoeWhite at 4:25pm 01.25.25 If i have to guess, the block on the end of the boom is part of the Dutchman reefing system. There s |
||
Fuel filter size
JoeWhite at 4:11pm 01.25.25 On my c36 primary fuel/water separator it is 2 micron. The engine fuel filter is 10 micron. No it do |
||
What is this on my boom?
thinwater at 3:53pm 01.25.25 A track for the reefing clew. Not common, but one of my boats had that. |
||
What is this on my boom?
stickinthemud57 at 3:43pm 01.25.25 As for the track on the starboard side of the boom, I have a similar one on my boom that I installed |
||
I'll never see this again
Crazy Dave Condon at 2:23pm 01.25.25 3/8 mile driveway uphill With steep incline with a 2-6 inch sheet of ice in the Virginia mountains. |
||
recommendations for a line cutter (on prop shaft) for a 2004 Hunter 41
Rich Stidger at 1:48pm 01.25.25 I have a simple serated disk that works very well. Mine is a one piece, but split ones are made so y |
||
Tuning guide
ldd at 1:26pm 01.25.25 I did try Seldom. They offered a general tuning guide. They suggested I contact the builder. On Bene |