|
John Bannister
at 5:51pm 12.05.02
5/879
Anyone had problems with this before and if so what have they done to resolve it ?
|
||
|
steve sylvain
at 3:36pm 12.05.02
1/1199
I have just purchased a 26' oday fixed keel boat which needs work. I have no information at all on i
|
||
|
tom
at 2:46pm 12.05.02
12/1369
Have a 22ft catalina that needs the wiring to the lights replaced. it seems, and i havent gotten to
|
||
|
ted jensen
at 2:45pm 12.05.02
13/1071
one of my winter projects is to add a binimi to my 35.5, if any one has a photo they can post, it wi
|
||
|
Charlie
at 10:17am 12.05.02
1/1095
I have just purchased a gennaker for my 23.5.I am considering mounting 2 swivel blocks to the padeye
|
||
|
Steve Brockhouse
at 9:17am 12.05.02
1/1096
I am the owner of a 1991 Beneteau 440 built in France and used initially in Guadaloupe as a Moorings
|
||
|
Mark Schenck
at 8:16am 12.05.02
1/837
Hey everyone, I recently stumbled into a 1982 Hunter 25 for a deal that I could not walk away from.
|
||
|
Tom Boles
at 6:42am 12.05.02
12/1895
Does anyone have a clever way to refinish the wood slats on the seats? We have a Vision 32 and even
|
||
|
john
at 6:36am 12.05.02
1/928
I have recently purchased a hunter 27' 1979. Many of the portlights are etched from exposure to sa
|
||
|
Joe Mullee
at 4:59am 12.05.02
46/7462
Recently I was in some rough weather while crewing on a boat in the Caribbean 1500. Winds were in th
|
||
|
Dave Johndrow
at 4:21am 12.05.02
1/1707
Don-I'm not sure where I read it but I do recall that you are not a fan of the loose footed Main.
|
||
|
Joe Refkin
at 3:58am 12.05.02
6/879
I have recently aquired an 83 Cat 30. It needs a name change. Will Island Girl safely remove the o
|
||
|
Brian R Clare
at 3:53am 12.05.02
8/1749
On my recently acquired '88 O'day 272LE with CDI reefer, the halyard/messenger knot is jammed at top
|
||
|
Stewart
at 3:23am 12.05.02
3/956
I find it hard to control the boat (motoring slow)when trying to dock in a tight marina. Should the
|
||
|
Lee
at 1:43am 12.05.02
5/921
I need to rebuild the galley to accomadate a small microwave. What type of wood is on the face of t
|
||
|
Greg
at 1:27am 12.05.02
15/1864
I was wondering if anyone has come up with any ideas on how to lift a 23.5 up off the trailer a bit
|
||
|
tomD
at 12:48am 12.05.02
12/3211
Several times last summer while cruising I elected to heave-to to go forward and deploy groundtackl
|
||
|
Neil King
at 11:58pm 12.04.02
14/1120
This has probably been asked a million times, but I'm new to this site: What is the most reliable o
|
||
|
Tom
at 11:49pm 12.04.02
0/764
and Catalina Yachts. For those interested. http://www.thelog.com/news/newsview.asp?c=7733
|
||
|
frank swift
at 3:33pm 12.04.02
5/1130
I am a new hunter 336 owner and when the gas gage was getting below about 1/4 I refueled. I was exp
|
|
Adding a Gas Cylinder to my Rigid Vang
tfox2069 at 1:08pm 09.09.20 Is that possible? I assumed gas would be sealed units. How rigid is your rigid vang? Doesn't it hav |
||
|
Catalina 310 with Schaefer 2100 Jib Furler - took apart, but can't get Stop Pin back in (1)
gscottnelson at 1:01pm 09.09.20 When you say "took apart" what did you do? If I remember - dangerous - without sail could push ex |
||
|
Job sheet jams
Ron20324 at 1:01pm 09.09.20 You could wrap it. Maybe with some amalgamating tape or electric tape. :plus: |
||
|
Quietest water pump?
Rich Stidger at 12:46pm 09.09.20 The Aqua King Shurflo pump I mentioned above is a four-chamber pump. Much quieter than the Jabsco t |
||
|
Job sheet jams
Scott B at 12:45pm 09.09.20 Looks like you can get behind the chainplate? I would try criss crossing almagamting tape over and |
||
|
Adding a Gas Cylinder to my Rigid Vang
Justin_NSA at 12:42pm 09.09.20 Is that possible? I assumed gas would be sealed units. How rigid is your rigid vang? Doesn't it hav |
||
|
Drilling hole to run lines through cabintop mounted traveller
Cole07 at 12:29pm 09.09.20 I'm not familiar with the boat, but I'm sure it wouldn't be a problem as long as you used a grommet |
||
|
Job sheet jams
Justin_NSA at 12:17pm 09.09.20 A crazy idea might be to fab a "plastic" washer with a center hole the size of the clevis pin, the t |
||
|
Quietest water pump?
kloudie1 at 12:00pm 09.09.20 I think you are talking about the single diaphragm pumps that sound like a machine gun.. obnoxious! |
||
|
Catalina 310 with Schaefer 2100 Jib Furler - took apart, but can't get Stop Pin back in
buddybear at 11:48am 09.09.20 When you say "took apart" what did you do? If I remember - dangerous - without sail could push ex |
||
|
Job sheet jams
JRacer at 11:46am 09.09.20 Or, is there any gap between the shroud/chainplate and that chrome strip? If so, you could use a sma |
||
|
Job sheet jams
JRacer at 11:42am 09.09.20 What if you cut the tube so that it was a half pipe below the chrome strip and a full pipe above? Th |
||
|
Unknown Sailboat Type
dlochner at 11:38am 09.09.20 Interesting little boat. On the upper right hand corner of the transom, there should be a series of |
||
|
Job sheet jams
JRacer at 11:28am 09.09.20 Short piece of PVC pipe with a large enough inside diameter to fit over the chainplate perhaps. |
||
|
Helm Steering Wheel Moved?
Dean Strong at 11:18am 09.09.20 Turns out the wheel can be flipped...which I did. Everything is line up again. Feeling a little fo |