Tugslife
at 4:46pm 08.06.20
6/811
I just wanted to introduce myself , and tell everyone I just became (Yesterday). The proud owner of
|
||
thwilson
at 3:37pm 08.06.20
8/6303
Does anyone have a good idea for making a simple cockpit folding table for a C-30? I'm more interest
|
||
Koltar
at 3:35pm 08.06.20
22/2647
Here is a link to a sailboat that I may get to start learning. https://www.facebook.com/marketplace
|
||
Mpoisson
at 3:15pm 08.06.20
16/1993
This may be a silly question....but, here it goes. I recently upgraded from my Catalina 27 to a 320
|
||
MDane2
at 1:53pm 08.06.20
3/7560
Hi folks, My family and I have for decades dreamed of owning an Alden sailboat, and are now starting
|
||
jviss
at 11:44am 08.06.20
7/632
Sailing today I went to check the tide info on the chartplotter, and the date was 8/05/2020 - yester
|
||
Ranger_12
at 10:12am 08.06.20
2/525
Does anyone know the WIDTH of the fin keel for a 1988 Catalina MK11? Need to see if it will fit on
|
||
stevenwp2
at 9:34am 08.06.20
9/1468
Moving forward with putting this Hunter 23 back together and found some cracks along the keel/hull j
|
||
LagunaJay
at 8:01am 08.06.20
5/438
It would have three inputs: 1) DC input for a solar PV array that could handle up to 40A @ 12V or 2
|
||
Captain W
at 6:30am 08.06.20
17/1539
I have an inboard gas engine that I has been giving me troubles since commissioning this spring. At
|
||
Marmalade
at 4:07am 08.06.20
2/419
Looking for a storage cradle for Legend 37 or 37.5.
|
||
Mike johansen
at 9:45pm 08.05.20
6/3307
I have a hunter 466 trying to outfit with a dingy and outboard for use as a tender. We used to stor
|
||
ontherocks83
at 8:40pm 08.05.20
3/718
So I'm not sure if this is the proper place to post this, but I had a thought and wanted to ask your
|
||
KZW
at 7:09pm 08.05.20
23/3039
Does anyone have an accurate wiring diagram for the 110 VAC in the C-310 A diagram of where the wire
|
||
Ladies night (1)
Jackdaw
at 5:31pm 08.05.20
8/1225
Yesterday, Jodi and three of her sailing besties took BlueJ out for a spin. They had a great time. C
|
||
Hunter216
at 4:33pm 08.05.20
4/599
|
||
ontherocks83
at 1:03pm 08.05.20
18/1781
I just got my power and internet back after almost 24 hours due to a storm so I apologize if someone
|
||
Jon Elliott
at 12:20pm 08.05.20
6/2399
|
||
kmart
at 12:07pm 08.05.20
9/980
Ok.. so due to relocating to a landlocked area.. I need to sell my Pearson 10M. Plan to do try and d
|
||
jviss
at 11:26am 08.05.20
1/530
There was a thread a while back where someone was saying that Westerbeke parts availability wasn't s
|
Pulling prop shaft off coupling procedures?
Tally Ho at 6:13am 11.26.24 If the shaft and coupling are newer, and not fused together, then yes, try to separate them. You mi |
||
Gelcoat or paste for touch ups and spider cracks?
Project_Mayhem at 6:06am 11.26.24 You could, but a slipped fluted dremel bit will cut through ANYTHING it can get near. 100% unforgi |
||
March Air Conditioner Pump Hose Connection Issue
colemj at 5:02am 11.26.24 No, you don't need marelon or bronze there. I think the pump body is nylon, not polypropylene, but |
||
Sail Recommendation
kappykaplan at 4:34am 11.26.24 I used the Quantum loft in Solomons for my new main and stackpack. Very satisfied with the results. |
||
Sail Recommendation
colemj at 4:32am 11.26.24 The Quantum loft in Annapolis is very good. I had a stackpack made by Evolution Sails in Deltaville |
||
Simpson Lawrence Sprint Atlantic B Parts
kappykaplan at 4:10am 11.26.24 You should post this in the classifieds section, not the general forum. |
||
Macerator pump mounting
dlochner at 3:45am 11.26.24 Pump motors should be level with the pump or above the pump. Pump motors are more likely to be damag |
||
Pulling prop shaft off coupling procedures?
dlochner at 3:42am 11.26.24 Take the coupling off the transmission and then get one of these tools. Makes getting the flange off |
||
Sail Recommendation
jssailem at 10:00pm 11.25.24 In Seattle we are fortunate to have several options. I know that the Precision folk nearby work hard |
||
Mast on a Hunter 19
Will Gilmore at 7:56pm 11.25.24 I am not familiar with the Hunter 19, but as a 61+ year-old man of six feet tall and average build, |
||
Pulling prop shaft off coupling procedures?
chuckwayne at 6:55pm 11.25.24 If your engine has not been installed yet, I would remove the propeller and pull out the shaft onto |
||
Sail Recommendation
Davidasailor26 at 6:54pm 11.25.24 Try some other lofts. I recently got quotes from several, most of whom would come to the boat to mea |
||
Pulling prop shaft off coupling procedures?
JoeWhite at 6:34pm 11.25.24 If your engine has not been installed yet, I would remove the propeller and pull out the shaft onto |
||
Mast on a Hunter 19
Crazy Dave Condon at 5:59pm 11.25.24 As a former Hunter dealer, I introduced both sailboats. The19 came with a mast raising system whic |