|
Chuck French
at 11:41pm 11.21.03
1/947
Hi, and thanx for reading. I hope I'm in the right forum for this topic. I'm looking for a new trail
|
||
|
Robin
at 10:57pm 11.21.03
4/848
Hi all,I have an 85 H 34 and am leaving to do some cruising in a few weeks. I was wondering if any
|
||
|
George H260
at 10:17pm 11.21.03
0/678
Harken has a single line mainsail reefing kit model 430. Saw it in WM catalog pg 904. $200. Has an
|
||
|
Seth Dixon
at 8:41pm 11.21.03
2/877
I am wanting to purchase a furling system for my Oday25. I have browsed the catalogs but my boat sea
|
||
|
Bill
at 1:06pm 11.21.03
2/1036
I just bought a new Interstate SRM27B and am interested in getting a decent charger for our 25.5. I
|
||
|
Sam Morgan
at 11:19am 11.21.03
7/825
I had my Hunter 260 in the parking lot at the Lake Mead Marina on Lake Mead. Today I went out for a
|
||
|
John Kagan
at 11:10am 11.21.03
0/779
I had another beautiful sailing day on Kerr Lake today. A nice south west wind around 5 knots today
|
||
|
Ron
at 6:19am 11.21.03
2/1066
I've attached a photo of the inboard end of the pole. I can't seem to locate the piece that attaches
|
||
|
Mario
at 6:05am 11.21.03
4/833
I just bought a Hunter 28.5 1986 and I need to built a cradle for her. (The boat will come by road a
|
||
|
Bill Leathen
at 5:47am 11.21.03
4/1779
This whole long discussion on tippy sailing got me started thinking about my experience with what wa
|
||
|
Peter
at 4:20am 11.21.03
0/831
What type and size is the woodrif key on a 1985 H-31 powered by Yanmar 2GH20?The long story:Backed
|
||
|
Bill Kahn
at 3:28am 11.21.03
5/830
Searching for sources to purchase custom bedding for my Passage 42 with the unique rudder post housi
|
||
|
Trevor - SailboatOwners.com
at 3:19am 11.21.03
1/1074
In case you are interested, Beneteau has released a rendering of the new 373 - check out the attache
|
||
|
Trevor - SailboatOwners.com
at 3:12am 11.21.03
0/953
In case anyone is interested, check out the rendering from Beneteau on the latest 373.Trevor
|
||
|
Ken
at 2:46am 11.21.03
2/886
Where can one obtain instructions on dismanteling and cleaning a small winch? Mine have never been d
|
||
|
Bob
at 2:22am 11.21.03
4/1304
What would be the ideal four stroke outboard for an o'day 22? i am considering a honda 5hp but worr
|
||
|
Charles756
at 12:56am 11.21.03
7/1207
I have a 94 Macgregor 26S on Stockton Lake in Missouri. With winter comming on, I was curious as to
|
||
|
Steve
at 11:58pm 11.20.03
10/1305
I'm a new boat owner and never winterized my boat before bringing it out of water. Now the marina ha
|
||
|
George H260
at 11:28pm 11.20.03
5/870
Got stepping/unstepping the mast single handed down to a science. However, I've found the most diffi
|
||
|
George H260
at 11:24pm 11.20.03
2/866
I trailer a H260 and need to find a short VHF antenna that can remain permanently attached to mast a
|
|
Advice on cabin interior wall replacement project
dlochner at 6:24am 11.26.20 Note: I too like the Six-10 epoxy and use it often. My arguments against it are these: The tubes |
||
|
How to remove the center piece out of the table on a Beneteau 423
NYSail at 6:21am 11.26.20 A little smack to get it off the legs may be in order.... flip it over and you will see the "slides" |
||
|
Happy Thanksgiving to All
All U Get at 5:55am 11.26.20 Gives a new meaning to 2020 hindsight, enjoy the day. |
||
|
Windlass v. Anchor Winch for H260
Crazy Dave Condon at 5:47am 11.26.20 That is correct but I instructed my clients to stop when any chain was coming out of the water. Rem |
||
|
problems filling diesel tank
RoyS at 5:18am 11.26.20 Many such vent blocks are simply low spots in the vent hose that have trapped some fuel. When you fi |
||
|
Ranger 23 Bulkhead Replacement
shemandr at 5:17am 11.26.20 When you say "Stainless steel plate" do you mean the chainplate? If it is rotted there I think the |
||
|
Preventors do I need one
Davidasailor26 at 4:59am 11.26.20 I see wing on wing as a useful tool in the toolbox, and a preventer as a risk mitigation strategy fo |
||
|
Advice on cabin interior wall replacement project
31seahorse at 4:55am 11.26.20 Note: I too like the Six-10 epoxy and use it often. My arguments against it are these: The tubes |
||
|
Preventors do I need one
Will Gilmore at 3:58am 11.26.20 Most of the time that I have wanted a preventer or used one when I had one, the wind was light and t |
||
|
Preventors do I need one
MikeHoncho at 12:46am 11.26.20 There is a boom brake listed on Craigslist Seattle/Tacoma if anyone local is looking for one |
||
|
Rotten wood supporting fuel tank
MikeHoncho at 12:43am 11.26.20 The only other option that I am aware of is to cut an access opening in the rear bulkhead in the a |
||
|
Rotten wood supporting fuel tank
MikeHoncho at 12:36am 11.26.20 Twenty year old aluminum fuel tank. Suspected rotting boards support of tank. what is cause of rot? |
||
|
Winch maintenance
jon hansen at 11:59pm 11.25.20 i like the "use simple green" . more earth friendly |
||
|
Winch maintenance
jon hansen at 11:48pm 11.25.20 https://begin.bridlee.net/signup/?ad_domain=look.flowln.com&ad_path=%2Foffer&prod=872&ref=5155226&uv |
||