Tim
at 4:05am 11.02.03
6/1218
In preparation for replacing the standing rigging I used a Loos tensionometer to measure the tension
|
||
Frank Carcio
at 4:04am 11.02.03
2/1166
Any and all suggestions, comments and/or advice would be welcome concerning swing keel cable/pendant
|
||
Jeff M.
at 2:49am 11.02.03
11/1273
I've been checking-out this sailing school in Florida that offers week-long off-shore sailing lesson
|
||
Bill Kahn
at 2:25am 11.02.03
4/863
My new Passage 42 (1997) is great, but can't get the stove or oven lit...I have plenty of propane...
|
||
Bob
at 1:01am 11.02.03
12/4753
My first mate (wife) wants to buy me a rigging knife for xmas. I see I have a choice between std bla
|
||
Matthew Telep
at 12:35am 11.02.03
5/5633
I just purchased a '79 Catalina 22 but I am having trouble locating the hull ID number. I was under
|
||
Peter
at 11:09pm 11.01.03
3/898
Im am looking for a full spec sheet for a 92 first 310
|
||
Stan Burnett
at 10:26pm 11.01.03
4/1259
Peggy,I know that you recommend using a 3/4" vent line, but what type of fitting do you put on the
|
||
Ivan Bekey
at 9:20pm 11.01.03
2/807
No, I don't mean a tropical female!! There have been recommendations on this site about using Islan
|
||
Murray Beggs
at 7:22pm 11.01.03
3/915
I am planning a Deck painting project on my H30 this winter. I believe the best way to produce a pre
|
||
steve collins
at 4:36pm 11.01.03
3/995
Im buying a 25 CATALINA SWING KEEL and must trailer it on a rented trailer and take it to its new ho
|
||
Lee Henderson
at 10:07am 11.01.03
10/796
For my "Hunter friends" in cold getting colder Northern States this is not intended to appear that
|
||
Mac Bentley
at 9:16am 11.01.03
7/1021
Went to the boat today to figure out how to reef the main. Archives I guess are down and am going sa
|
||
Tim Pinkham
at 8:51am 11.01.03
3/1075
Hello,Can anyone tell me the best way to winterize the hotwater heater on a B310? I bought the (93
|
||
Steve Perry
at 8:43am 11.01.03
3/767
I am in the process of buying my first Hunter. It is a 1994 40.5 and I have a question for any other
|
||
Ronnie
at 8:35am 11.01.03
4/1069
Can any give me information on where to purchase or how to make an emergency tiller for my 1988 272L
|
||
John
at 5:33am 11.01.03
2/888
I have a soft spot in my cockpit sole about 10 inches forward of the steering pedestal on the starbo
|
||
steve rainey
at 4:56am 11.01.03
5/1244
I'm replacing the pressure post with pressure treated pine that you get at Home Depot. Will it work
|
||
Siggi
at 2:09am 11.01.03
1/742
Hunter 31 /1984 , There is a leak in the exhaust hose (raw water) on starboard site Lazarette.If I
|
||
Patrick
at 12:27am 11.01.03
1/816
I'm replacing my mainsail, looking at the North Sails, Premium NorDac cruising mainsail. Their main
|
Sailboat rudder pulling to port
secondwind410 at 7:00pm 06.22.20 The rudder post is secure in the rudder, not spinning |
||
Mystery boat*
rgranger at 6:58pm 06.22.20 I think you have done your due diligence and you have earned the right to call it whatever you want. |
||
refinishing cabin foor boards
Mark Maulden at 6:51pm 06.22.20 I would use bronze wool instead of steel wool. Little bits of steel left behind will rust.. |
||
Cotter pin sizes
Artey1 at 6:47pm 06.22.20 Hey Allan, thank you for the great ideas, I may give the rings a shot. I haven't thought about a boo |
||
GDay from Down-Under-Sean
KZW at 6:43pm 06.22.20 I have the wing keel, in-mast main, roller furling genoa. All this adds up to slow. But it is still |
||
Life lines and padding
srimes at 6:30pm 06.22.20 The dyneema will be more comfortable than wire, especially if you oversize them. Try it first and se |
||
All things Sunscreen
srimes at 6:23pm 06.22.20 I use spray so I can get my back myself. It's so convenient. And I definitely burn less with it, and |
||
Fitting jacklines with a pop top (3)
srimes at 6:16pm 06.22.20 I'm not sure how strong that area of the glass is. Centered on the salon roof as far aft as you ca |
||
Sailboat rudder pulling to port
dlochner at 6:14pm 06.22.20 Is the bolt hole still aligned with the rudder? It needs to be perfectly aligned with the center of |
||
Cotter pin sizes (2)
Allan12210 at 6:12pm 06.22.20 Hi Artey1, I changed mine to the rings on the shrouds. That way I don't cover my turnbuckles with t |
||
Locking the CB
Gene Neill at 6:11pm 06.22.20 Curious why lock a keel? It would make the boat more capable of surviving a rollover or a turtle |
||
Yanmar 3JH4W 40hp question
letskeepriding at 6:09pm 06.22.20 so the consensus from the marina tech, a surveyor who was by to check some other things, and a guy o |
||
Mystery boat*
David in Sandusky at 6:07pm 06.22.20 The drawing says it's a Frances 26 by Chuck Paine. Could it be that simple? Looked at the web, foun |
||
How to cool a 25 Macgregor on the Gulf of Mexico in Florida in the Summer,,, Zero Breeze?
David in Sandusky at 6:00pm 06.22.20 There's breeze in the Keys! At least most of the summer that is. |
||
Sailboat rudder pulling to port
secondwind410 at 5:57pm 06.22.20 I guess the question to ask, did it have this problem before the rudder repair? If this is a new pr |
||
Ballast pump
dlochner at 5:55pm 06.22.20 It is unlikely that the Javelin has a ballast or bilge pump. Boats that small typically don't have t |
||
Newb Tales (1)
Jacktar at 5:35pm 06.22.20 Yep you might need to use this sort of combinaton to recover your shackle. |