Serving sailors online since 1997
 
 

Recent Topics

FrostyBeverage at 11:25am 04.18.20
21/2315
I recently purchased a 2005 Beneteau 323 with a furling mainsail and a US Spars Z400E mast. The sai
joecool911 at 10:26am 04.18.20
5/1938
Does the dinette table in the H26 convert to a full area bed?
Valerio at 9:17am 04.18.20
5/557
Hi to all h41 owners, my h41 only comes with an halyard each for genoa, spy and main, I would like t
Grace on hard at 8:05am 04.18.20
12/1270
My S2 dragged anchor and went aground tearing the rudder off the rudder post. ( see photo). I need t
jsachetti at 7:26am 04.18.20
4/1311
The handrail on my oday 25 is leaking in only the forward t3 bolt holes out of 10 bolt holes. I trie
sailme88 at 7:00am 04.18.20
10/638
At least it isn't accumulating.... otherwise I'd be shoveling white fever from the driveway this mor
jssailem at 6:30am 04.18.20
6/554
With all this time ashore, after viewing the forum, imagining the cruises ahead, plotting my trips,
FlimFlamII at 6:24am 04.18.20
7/899
It was running under power fine when suddenly the engine began racing and pouring out smoke. I shut
Joe Perez at 10:29pm 04.17.20
12/1941
Brian D at 7:35pm 04.17.20
10/775
177714
Starboardport78 at 4:54pm 04.17.20
26/2301
Hey everyone, I have just got my first sailboat. A Starwind 19 and I have no idea how to find the
Clydo at 2:57pm 04.17.20
29/6218
Question is how long do our lift pumps last? Went back four years in archives and very few comments
Brian D at 1:00pm 04.17.20
11/598
Here is one more from my collection. Performed on a 2006 Martin D12X1 12-string. D_cacyVUeHk
LakeShark at 11:04am 04.17.20
15/2894
Ok so I have been around long enough to know that this has been discussed before but not for a while
Phil Herring at 4:10am 04.27.20
13/1255
Where do you turn when you have a problem with your boat? A trusted local mechanic, rigger, or yard
lostintime at 9:41am 04.17.20
7/1071
Good all, and thanks in advance for any help given. I have an 1983 Catalina 30. I am removing and
tadd5181 at 9:34am 04.17.20
12/2814
I have an 2000 Hunter 420. Its older AM FM radio sound plays into marine grade speakers in my cockp
sbcwolff at 9:01am 04.17.20
20/2494
I understand this will take YEARS of work, and tens of thousands of dollars, but would we be crazy t
JohnEh at 8:45am 04.17.20
12/1497
I recently acquired a 2000 Hunter 410. There is a fuel gauge located at the helm by the tachometer.
JohnEh at 8:33am 04.17.20
8/1240
I recently acquired a 2000 Hunter 410. The boat has three fresh water tanks with three deck fills an

Recent Replies

2gm20f water heater circuit
JoeWhite at 5:30pm 11.03.23
Yes. Take a hose connect from one to the other at the engine.
Its funny Friday!
Kermit at 5:29pm 11.03.23
Kermit, here's my boat book on the coffee table. awmill cut the top and bottom flat but when we pul
Oday keel
Yoho Yoho at 5:22pm 11.03.23
Thanks for the info. That makes sense. No picture because I am probably not going to get this boat
Oday keel
kappykaplan at 4:41pm 11.03.23
The fin keel on this boat has a drain plug near where the keel is fastened to the boat. It is poss
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Tally Ho at 4:12pm 11.03.23
2595 Not THAT many hours, my old 2GM20F has over 2000 hours. I hope you can get it sorted out (a
MaxProp prop   (1)
Tally Ho at 4:09pm 11.03.23
Thanks for the replies. I went over the recommendations from PYI and FoF again, and PYI is recommen
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Alan Gomes at 3:51pm 11.03.23
Update: apparently there is also significant scoring on the nozzle pins of two of the three injecto
H50 master cabin headliner ceiling
artboas at 3:50pm 11.03.23
I believe that @artboas has posted on this, but couldn't find it. I'm attaching a link to a YouTub
Engine Sensor ID
DyverDown at 2:50pm 11.03.23
From the yanmar parts catalog it looks like you are correct looking for part number 127610-91350.
MaxProp prop
jssailem at 2:48pm 11.03.23
I was going to say (from memory in talking with WestbyNorth) 10-15% OF PROP DIAMETER. Then I though
MaxProp prop
dlochner at 2:43pm 11.03.23
The distance between the end of the prop and the strut should be about 1 shaft diameter, but it is n
Rebuild of high pressure fuel pump for Yanmar 3GM30F
Tally Ho at 2:35pm 11.03.23
How many hours on your engine? Greg
Thru Hull Replacement?
Crazy Dave Condon at 2:27pm 11.03.23
As a former Hunter dealer in North Carolina, I can understand it is expensive to haul out and I con
Thru Hull Replacement?
Tally Ho at 2:24pm 11.03.23
MaxProp prop   (2)
Tally Ho at 2:16pm 11.03.23
Interior Wood
Siamese at 2:16pm 11.03.23
I'd oil it. Wouldn't use varnish, but I might use a water based poly product. I would consider pain
Rewiring masthead and forward steaming light   (1)
rgranger at 1:57pm 11.03.23
after it somehow got smashed against a piling the first month I had my boat. Could have been worse.

Copyright 1997-2024 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.