Serving sailors online since 1997
 
 

Recent Topics

Chris at 6:35am 08.19.04
1/796
Hi everyone, Does anyone have any info concerning icemakers and relative costs. Sure would appreciat
Stapper at 5:38am 08.19.04
0/1037
amir at 4:52am 08.19.04
1/847
Hello, I have a H 336 that has a full batten main sail. I was wondering if anyone has tried to adj
Joe at 4:40am 08.19.04
8/974
Help!! I'm taking my mast down for the first time this weekend. I have NEVER done this before. Can s
Tom at 4:39am 08.19.04
7/2063
I am looking on having a dodger added to my boat and there seems to be two options. Some dodgers ar
HOLDFAST at 4:33am 08.19.04
0/765
Does anyone have specs. on the New Hunter 25 for 2005? I understand that the 260 will no longer be m
Steve Carpman11081 at 3:28am 08.19.04
3/1030
Our water pump cycles on when no faucet is open. This may occur 2-3 times during the night, which ha
Bill Rinckel at 2:44am 08.19.04
8/1751
When motoring out of my slip in the shipyard I have to make a very sharp turn to starboard to remain
Paul McGhee at 2:44am 08.19.04
3/988
We're planning on going to Block Island for Labor Day weekend. I love Block, it's hard to let a seas
Molly1034 at 2:29am 08.19.04
2/1242
The interior seats in my 1997 h26 are a little sticky. This is even true on the back side which has
Dick12150 at 2:24am 08.19.04
1/1046
Local conditions at our new home port make the recommended anchor for our 30 foot, 10,500 pound Hunt
sailconnie at 2:22am 08.19.04
2/1471
Is anyone presently sailing with a spinnaker on their 216? Is it Hunter issued?
jon at 2:03am 08.19.04
8/1814
I recently bought a 1984 Mac 25 that needs a little work. The rear bulkhead panel, below the compani
Calif. Ted at 1:37am 08.19.04
0/965
While in local auto parts store, thought I'd pick up some ATF (type A) as specified for Hurth gearbo
Gregg D at 1:32am 08.19.04
5/901
How tight should the shrouds be? I tried to adjust them last weekend and when I went to raise my ma
Elliot at 1:32am 08.19.04
1/1205
We'll I seem to have gotten myself stuck in a pickle. The previous owner installed a new Westerbeck
Don Guillette at 1:30am 08.19.04
5/1288
Eric Graig asked me an interesting question. He asked "If I were going to buy only one of your produ
neil r ostrofe at 1:20am 08.19.04
2/1022
i am looking to replace my evinrude yachtwin 6 on my oday 222 .what would be the max motor weight an
mike mills at 12:52am 08.19.04
3/969
would one know the most inexpensive way to frieght a 37ft yacht from florida to uk,was going to sail
mike mills at 12:46am 08.19.04
0/984
I have found that my recently purchased yacht is a light airs boat and as such not the thing for cro

Recent Replies

Winter sailing (Or Summer if you're below the equator)
Terry Cox at 8:34am 01.24.21
Hi Ken, just got back from a week on the water. A bit chilly out there. Sorry, no pictures to share,
Amount of Exhaust Water out the back
Capt jgw at 8:32am 01.24.21
Here's a link to an earlier thread. Same question, same answer. https://forums.sailboatowners.com/p
Yanmar 2GMF to 3GMD swap??
xavierspl at 8:31am 01.24.21
Ok well, I've basically going back and forth with the guy, story goes, he got it with a bunch of oth
Yanmar 2GMF to 3GMD swap??
Justin_NSA at 8:27am 01.24.21
These are just my opinions. I've swapped a few car engines but never a boat. I even rebuild the dies
Yanmar 2GMF to 3GMD swap??
kloudie1 at 8:24am 01.24.21
Check that the GMD has a heat exchanger on it for "fresh water cooling" .. Kind of confusing in your
Delrin Sheaves
Terry Cox at 8:24am 01.24.21
Very nice inventive solution. Although the aluminum sheaves appear to have rounded bottoms, perhaps
Delrin Sheaves
dLj at 8:21am 01.24.21
One of my little projects for the winter was to make new sheaves for my masthead which I hope will
Yanmar 2GMF to 3GMD swap??
xavierspl at 8:19am 01.24.21
The person selling doesn't know how many hours, I basically have little to go off other than the fac
Yanmar 2GMF to 3GMD swap??
Justin_NSA at 8:02am 01.24.21
Motor mount alignment and transmission mating would be my guess. Probably less work than a rebuild i
New to me Hunter 26 clean/refit
Crazy Dave Condon at 7:44am 01.24.21
Tie down winch handle on trailer stand as I have seen locking mechanism come loose. The one on trai
Hunter OEM Solar panel set up
Windpilot at 7:43am 01.24.21
Hi Don, I traced all the wiring because I replaced it with a bigger panel, heavier wiring and now ha
Delrin Sheaves
jon hansen at 7:23am 01.24.21
YES! well done sir thanks for sharing
WM BOGO sale for Winches gone forever??
MikeHoncho at 7:19am 01.24.21
When I ordered my Lewmar 40STs on bogo with WM they charged me full price for one, sent it then I wa
Delrin Sheaves
Kings Gambit at 7:13am 01.24.21
Depends on the Delrin some is UV stable. https://www.boedeker.com/Product/DELRIN-527-ACETAL OK. I
Hull speed and fuel consumption Hunter 30   (1)
Pizzazz at 7:11am 01.24.21
I calculated average nmpg for my Hunter 31, 2GM20F engine. This was in calm water in the marina. I u
How to make your mask fit better
kappykaplan at 7:10am 01.24.21
Tks! :thumbup:
Amount of Exhaust Water out the back   (1)
Capt jgw at 7:10am 01.24.21
Again, it sounds like this engine is acting exactly as it was designed to. If not equipped with a he
Winter sailing (Or Summer if you're below the equator)
Hunter216 at 6:46am 01.24.21
You could check out @Bill19233 postings as he seems to sail all year. :)
Exchange Jib lines?
jssailem at 6:24am 01.24.21
Thanks Ward. Being a rigged at the mast guy I sometimes forget you guys run the lines to the cockpit

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.