RichardL
at 2:46am 06.28.04
3/854
Does anyone know if I can I still raise and lower the mast easily with the mast raising kit if I hav
|
||
Paul17588
at 2:38am 06.28.04
2/1057
The forward harch on my 1974 Oday 22 needs to be replaced. The original had some sort of translucent
|
||
Paul17588
at 2:35am 06.28.04
1/1106
I have an 1974 Oday 22, last year the winch handle went over the side. It fit into the winch from th
|
||
sailordll
at 2:17am 06.28.04
4/1115
Hello,I know this was recently discussed but I can't seem to find the posts in the archives (archiv
|
||
John J6388
at 2:14am 06.28.04
1/991
I had recently read that this is good for cleaning life-lines, and it is. After cleaning apply a coa
|
||
fredsb
at 2:07am 06.28.04
2/893
My boat (84') came with Roller Furling (Schaefer SnapFurl) when I bought it a year back. The last o
|
||
asmith
at 2:02am 06.28.04
1/938
I have a 2000 Catalina 310 with a Universal diesel. I'm looking for an all around service person who
|
||
jclay
at 1:55am 06.28.04
1/972
Can the water capacity be increaced on the late '80's 35'-40' Hunter Legends? Anyone know of articl
|
||
Steve Baardson
at 1:53am 06.28.04
4/1052
I am a new owner of a 1995 Catalina 270. It has an 18hp Westerbeke engine. Over the weekend, the "
|
||
John J6388
at 1:41am 06.28.04
0/1017
I had recently read that this is good for cleaning life-lines, and it is. After cleaning apply a coa
|
||
Bill C320, Papillon
at 1:26am 06.28.04
3/1569
I have an odor that I can't seem to get rid of. I have your book and have cleaned everywhere that I
|
||
Jack McD
at 12:59am 06.28.04
8/954
The water pressure pump on my 2003 Cat 320 cycles for a fraction of a second about every seven or ei
|
||
agolden
at 12:52am 06.28.04
1/1103
I am removing several canvas snaps screwed into the fiberglass on my boat and would like some input
|
||
TomS
at 12:47am 06.28.04
7/5745
In March there was a thread about ST 4000 autopilot problems. Mentioned was that a rudder reference
|
||
DreamWeaver13428
at 12:32am 06.28.04
5/1161
The freezer/refrigerator on our model 350 ran continuous no matter what setting the freezer section
|
||
T J Furstenau
at 12:29am 06.28.04
2/1199
Peggy -Was hoping you could give some input on my "new" Jabsco electric head. Just got the boat t
|
||
robertaho
at 12:05am 06.28.04
0/967
I have an Idylle 13.5, and I'm looking for parts for my stove. All the model and make information h
|
||
Sonny10775
at 12:03am 06.28.04
4/885
I am new to sailing, and as I'm looking around my boat I see this line that says Jib Outhaul. Its no
|
||
R4576
at 11:24pm 06.27.04
0/905
Hello fellow Catalina owners. I have a 1994 Cat320 with a dodger, bimini and plastic cockpit enclos
|
||
Ralph18418
at 11:13pm 06.27.04
2/869
Help. I have a 1979 Catalina 25 with a swing keel. Between the cabin floor and on the starboard side
|
Marvin "Guy" Royal at 7:52am 07.30.20 I have a Peake tri-radial asymmetrical spinnaker with a CDI top down furler (used once), ATN sock a |
||
How deep to launch
LakeShark at 7:52am 07.30.20 Ready to launch. Fully extended....backed down till she floated off. WOW that's one of the rare ti |
||
Solar Vent on a head hatch.
capta at 7:50am 07.30.20 Capta, Marinco/Nicro calls it a shutoff damper. https://www.marinco.com/en/~/media/inriver/382 |
||
How deep to launch
LakeShark at 7:49am 07.30.20 obvious, but sometimes overlooked.....if a kick-up rudder, make sure it is "up". If not a kick-up, |
||
Eractic Tachometer and engine power
capta at 7:46am 07.30.20 There should be a sensor located somewhere on the bell housing of the transmission. Remove the 2 w |
||
dorade box cowl vent
capta at 7:37am 07.30.20 Who cares about the air those dorades provide? They and the rest of the brightwork look fantastic! |
||
Rigging a Capri 165
Johnfranklin1 at 7:31am 07.30.20 I think this is the appropriate part. Perhaps contact them to confirm for your specific boat. http |
||
Rigging a Capri 165 (1)
Johnfranklin1 at 7:29am 07.30.20 Maybe I connect the pendant to the vang with this? |
||
Rigging a Capri 165
Hunter216 at 7:28am 07.30.20 I think this is the appropriate part. Perhaps contact them to confirm for your specific boat. https |
||
Rigging a Capri 165
Johnfranklin1 at 7:27am 07.30.20 I would point out the screw is quite loose where a shroud (I think) is attached. mast and on throu |
||
Rigging a Capri 165
Johnfranklin1 at 7:19am 07.30.20 Thanks Joe, Lets say I want to use a pendant. What is the series of parts in the connection b |
||
Shifter Cable....new unwanted project!
Crazy Dave Condon at 7:19am 07.30.20 If the cable exits thru a hole in the bottom of the pedestal, there is a trick trying to navigate th |
||
Invest 92L (1)
JamesG161 at 7:11am 07.30.20 Tropical Storm Isaias barely made that status overnight, as the CCW motion became apparent. The H |
||
Beneteau 331 engine room fan
Caboteur at 7:05am 07.30.20 After a partial meltdown of the ignition wiring and after changing the whole harness once I rewired |
||
Rigging a Capri 165
Joe at 7:02am 07.30.20 Is there a tang here? The hardware rivetted to the mast to support the jib/forestay is called a "m |
||
Shifter Cable....new unwanted project!
Dave Groshong at 6:55am 07.30.20 I don't know the length, but here is a link to the replacement for the old 3300 cables https://sho |