85bittersweet
at 12:05pm 06.10.20
4/398
What does everyone like?
|
||
Rennsail
at 11:11am 06.10.20
11/1272
Getting back into sailing after a 25 year layoff. So I bought a well-sailed '77 Catalina 22 last nig
|
||
WaltH
at 10:36am 06.10.20
4/567
I have a Hunter 460 and have to replace the steering ball joints. The one closest to the wheel is on
|
||
Jaysway1
at 10:12am 06.10.20
12/984
Hi I have an oday 23 favtory calls for a 15hp but I wanna sail lesson use motor more could I upgrade
|
||
Sailing Solo (2)
Tarkus
at 9:57am 06.10.20
11/1373
Hello everyone, I just purchased a 1974 Catalina 22 last fall. Its been 35 years since I last sailed
|
||
Guan
at 9:24am 06.10.20
14/1352
My 2001 B361 westerbeke tachometer starts up from 0 and jumps to 2500 and back to 0 on minimal accel
|
||
azambella
at 7:49am 06.10.20
5/465
I found some older 4" horizon depth and speed log units (in good shape) but my broken ones have moun
|
||
unfeast
at 7:41am 06.10.20
12/903
Saw them in the listing, and wasn't sure what they were. Thanks in advance.
|
||
Bogart
at 2:27am 06.10.20
2/497
I have a 2007 45cc, imported direct to Australia from new and therefore set up with a 230V AC system
|
||
O'day 22 rescued (2)
jmczzz
at 10:56pm 06.09.20
14/1376
From 6 years sitting in the driveway near Lake Michigan. (maybe not). Question: Were the cabin sides
|
||
patrickkidd
at 10:11pm 06.09.20
2/426
I am trying to figure out how to remove my floor so I can have a look at and possibly the probably v
|
||
P12nash
at 8:59pm 06.09.20
2/593
|
||
KenK13623
at 6:25pm 06.09.20
4/456
Does anyone know where the AC raw water pump is plugged in or connected to power. I may have a prob
|
||
Leeward Rail
at 5:14pm 06.09.20
20/1947
Found these in an old cabinet. Any idea what they are ? One looks almost like an impeller or somethi
|
||
thetone
at 5:04pm 06.09.20
4/561
Does anyone have any information on replacing the water separator and oil filter on my 1990 Beneteau
|
||
Epic Epoxy Epoch (1)
Will Gilmore
at 3:45pm 06.09.20
2/416
Just thought some of you, who do your own work, might be interested in this Web Blog. The original
|
||
GregB26s
at 3:23pm 06.09.20
2/666
I have a MacGregor 26s, the cable on the swing keel needs replaced. I have removed the keel jus
|
||
Paleczny
at 2:49pm 06.09.20
6/1029
I have just aquired a 1993 Hunter 23.5 and am rigging it for the first time. The boat does not have
|
||
Cest La Vie
at 2:47pm 06.09.20
19/1505
For those of you who share the fresh water environment, we are blessed to avoid the barnacles and ot
|
||
conzip
at 2:37pm 06.09.20
3/1698
My Ensenada 20 had a broken mast foot. Previous posts suggest contacting IdaSailor. They are now R
|
Remove Prop
Tally Ho at 2:54pm 11.18.23 What would make tightening the nuts easier isn't a finer thread on the all-thread. It's a longer wr |
||
Rudder slack
Ralph Johnstone at 2:45pm 11.18.23 Not sure about his boat, but my '79 H30C has a skeg. :) Obviously I'm not invited to travel in th |
||
Water /humidity?
Don S/V ILLusion at 11:40am 11.18.23 Assuming your boat is in Tampa, the amount of moisture in the air during hot weather will far exceed |
||
Rudder slack (3)
Ralph Johnstone at 11:31am 11.18.23 There was an approximately 1?2" gap between the top of the rudder blade and the bottom of the skeg. |
||
Water /humidity?
Ralph Johnstone at 11:11am 11.18.23 Watch out for outdoor temperatures. Dehumidifiers can produce extremely high temperatures in your h |
||
Water /humidity? (1)
Ralph Johnstone at 11:07am 11.18.23 regarding a machine that makes water out Should that be "takes" water out ? If that's the case, |
||
Bronze rudder part
dlochner at 10:45am 11.18.23 That looks like fairing compound more than a barrier coat. The horizontal crack just below the bare |
||
Water /humidity?
Richard19068 at 10:40am 11.18.23 Makes water out of what? The atmosphere like a dehumidifier? |
||
Hunter 306 vertical play on Rudder Stock.......how to fix?
JamesG161 at 9:43am 11.18.23 where did you get the instructions and photos of the installation you included in your post? Look |
||
Bronze rudder part
GarEi at 9:27am 11.18.23 bronze, I guess I will grind or sand back epoxy barrier coat until I find good adheasion and reappl |
||