Serving sailors online since 1997
 
 

Recent Topics

york brown at 2:12am 01.14.05
1/1530
I just purchased "PYXIS" and she is a 68 C-28 hull # 303, how do I know if she is a MKII or not?
R Dunn at 12:58am 01.14.05
2/1077
I have a 1982 33'(77-83) and want to replace the interior hull covering, which is currently a carpet
Brian at 12:31am 01.14.05
9/1196
Have any of you Passage 42 (1990-1998) owners upgraded your Jabsco electric toilets with the Raritan
Otto Dieffenbach at 12:24am 01.14.05
2/1068
If you have an all white sail its is not immediately obvious, at least not to me. The sail has a bui
Kenny at 12:20am 01.14.05
0/885
http://www.geocities.com/kenny27870/springfling2.html is the new website for the Spring Fling . Chec
Stephen OBrien at 11:46pm 01.13.05
11/1578
Anybody know where I can get replacement knobs that secure the portlights? Mine are white plastic w
Bro Paul at 10:55pm 01.13.05
7/1303
I have just recently purchased a Hunter 31. During the survey I noticed that I have about a season l
Steve at 10:13pm 01.13.05
7/1132
Jim at 9:56pm 01.13.05
3/868
I seem to sail faster with a reef in. I have a Hunter 306 and I have never gone faster than 5.7 kno
r white at 11:24am 01.13.05
1/1611
looking for information regarding this boat
jeff K at 11:10am 01.13.05
5/4374
I have a 2003 26M with a Johnson 50hp 2 stroke and I get about 16-18 mph(GPS)max. If anyone has this
Jon at 10:21am 01.13.05
0/743
Hi All I just ordered sails for my 322, radial cut composite jib and high aspect main fully battene
Tip at 9:50am 01.13.05
4/990
I want to buy a Hunter 260 water ballast sailboat. I have to navigate a shallow part of the neighbo
Tip at 9:39am 01.13.05
4/777
I just looked at a 2003 Hunter 260. I asked the dealer about the factory 5 year hull warrantee whic
Mark at 9:11am 01.13.05
7/800
At last I "think" the rigging on the 260 must be OK. After messing around for some time with shroud
Dan Marantz at 8:29am 01.13.05
2/1329
I have a 1972 Catalina 27. The traveler is located at the rear of the cockpit. I would like to know
John Richard at 7:28am 01.13.05
4/1184
http://www.yachtaragorn.com/Thailand.htm Here is a very freightening first hand account of the rece
Spen at 7:11am 01.13.05
4/1105
Marc at 6:12am 01.13.05
6/1057
Hi, I am just dropping by to see if I can get some help with this: I am working on a 3D image and I
Gene at 5:05am 01.13.05
7/882
I am interested in connecting a computer at the navigation table hooked to the GPS and then send the

Recent Replies

Help with shore power
Ralph Johnstone at 5:28pm 03.09.21
Do you have a multimeter that you can use to test voltage at the shore pedestal, end of the cable,
Help with shore power
Calif. Ted at 5:22pm 03.09.21
I have been looking around and have not found any other fuse boxes or switches. There should be a
H37C Companionway Width Measurement Needed
sail sfbay at 5:19pm 03.09.21
Take a look at the options here and call them to confirm the number of boards and dimensions: Hunte
replacement pads on my jackstands question
Capt Robbie at 5:17pm 03.09.21
seal plywood with good patio deck sealer then place a foam garden pad between the hull and pad.
Darn raw water intake blocked again
Davidasailor26 at 5:15pm 03.09.21
Maybe try something like a dinghy air pump to push whatever is causing the blockage back down and ou
Newport 30, exposed keelbolts?
heritage at 5:11pm 03.09.21
I assume the the bolts and nuts are both of stainless steel. The bolts are shiny because they have
H37C Companionway Width Measurement Needed
sandpiper10471 at 5:10pm 03.09.21
Careful. I suspect those drawings are for a Hunter 37 which is very different from a Hunter 37C. My
Help with shore power
higgs at 5:10pm 03.09.21
David has the solution. Use a meter to determine where you are getting power and where that ends.
Hunter 456 cutlass bearing   (1)
sail sfbay at 5:07pm 03.09.21
Please refer to the diagram from the 456 manual for cutlass bearing size.
Darn raw water intake blocked again
Dr. D at 5:06pm 03.09.21
Should it have drained? Mine is above the waterline but it doesn't. I thought perhaps the entire
Hunter 49 Staysail
ScottySailor at 5:03pm 03.09.21
I have my Hunter 50 in the Caribbean where 25 to 30 kn is common. I found that sailing a beat in 32
Serpentine kit for Ample Power alternator
Maine Sail at 4:47pm 03.09.21
I have an Ample Power 105A alternator on my M25XP with the stock 3/8" v-belt and I would like to up
Air Conditioning unit in 37.5
Unwinder at 4:45pm 03.09.21
I have a similar installation in OLD CROW a 1996 37.5 as rjarrell stated above except unit is a R22
Air Conditioning unit in 37.5
Unwinder at 4:42pm 03.09.21
Have a single self contained reverse cycle Mermaid Air 16500 BTU on my 37.5. Mounted under port set
Hunter 456 cutlass bearing
MitchM at 4:38pm 03.09.21
cutless bearing dimension is related to diameter of the propshaft it's installed on. know
Neck deep in the Dark Side
MitchM at 4:35pm 03.09.21
o heck. i'd go for the ranger tug 31 w command bridge, solar, twin yanmar diesels, 3
Mast cleaning/buffing... without climbing?
sail sfbay at 4:01pm 03.09.21
Agree with Rich Stidger & Justin_NSA!!
H37C Companionway Width Measurement Needed
Brazil at 3:53pm 03.09.21
EXCELLENT! Thank you very much.
H37C Companionway Width Measurement Needed   (1)
sail sfbay at 3:42pm 03.09.21
https://shop.hunterowners.com/hp/part.php?m=37&c=19&p=55426

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.