Night Sailor
at 10:08am 10.26.04
0/893
I have the mast off the boat for some modifications, and decided while it's down to also do a cockpi
|
||
Ron
at 9:51am 10.26.04
8/1348
What are the draw backs of using daisy chained 6 volts? Can I use my Guest shore power charger? It s
|
||
Manuel
at 9:29am 10.26.04
6/990
I need help in finding a cheap place to buy the rigging stainless steel cables that hold the mast. M
|
||
Ken
at 9:28am 10.26.04
8/910
Hi, anybody using OEM filters in their Yanmar. Fram has cross referencing. I have a 28.5 with a 2G
|
||
Jim
at 9:08am 10.26.04
3/938
Looking for info on where I can find 7hp Vire, 2 cycle gasoline engine and how much they may cost?
|
||
Ron
at 7:41am 10.26.04
9/1256
A new boat (4 yrs. old) and I would like to remove old decal and rename, any suggestions on products
|
||
Brad18297
at 7:31am 10.26.04
20/1915
I have a 2000 410. I really could use assistance in docking this boat with Wind and Current always
|
||
carl
at 6:56am 10.26.04
7/1380
my thru hull depth transducer that is mounted inside the hull and sits in a small oil cup that is gl
|
||
Greg
at 6:54am 10.26.04
2/902
I became the proud owner of a 2000 250K several months ago. The boat needs to get out of the cold cl
|
||
Tom Monroe
at 5:18am 10.26.04
8/1232
... all over my boat?Went to the boat Sunday, and the rigging was covered with what looked like lo
|
||
chris
at 4:04am 10.26.04
7/1002
We have a 1982 Hunter 27 with merriman yacht specialties steering pedistal. To maintain throttle rpm
|
||
Michael Slough
at 3:58am 10.26.04
0/1032
I have a 1988 H23 wing keel, and would like to install an autopilot, probably ST1000, and would like
|
||
Guy
at 3:34am 10.26.04
6/1171
I have noticed the inside of my tires are wearing more than the rest of the tire. I guess it could b
|
||
p323ms
at 3:28am 10.26.04
1/1861
I have a walter V drive with a MD11c engine. The coupling between the drive shaft and the transmissi
|
||
John T1594
at 2:54am 10.26.04
3/870
This is the first year that I will not be able to warm the engine before winterizing it. The boat (H
|
||
Harpy
at 2:51am 10.26.04
4/1183
Anyone have any suggestions on where to purchase and/or advice installing new standing rigging on a
|
||
John Dildine
at 2:48am 10.26.04
1/847
I am trying to figure out how to rebuild my 1977 Hunter 30. Need a mast, rudder repair, some standin
|
||
Alan
at 2:32am 10.26.04
1/763
I recently acquired a 1994 Hunter 40.5 and have been trying to figure out the electrical charging sy
|
||
Ben Stavis
at 1:54am 10.26.04
5/951
Hi Peggy,I am still planning a holding tank for my Rhodes Reliant, more enlightened by reading you
|
||
Warren M.
at 12:46am 10.26.04
12/2040
I have a Hood 810 line drive furler that is in need of a new continuous furling line. Much to my su
|
Yanmar 3GMD Just Shuts Off, Restarts Later
joker460 at 7:59pm 08.19.20 Just a thought. If there is no fuel issue as you say, then I would suspect electrical. As the engin |
||
Jib roller furling line block
Dave Groshong at 7:39pm 08.19.20 It's a common cheek block, I don't think you can get that exact one any longer, but give me a call |
||
replacing cdi halyard
Serenity on Hudson at 7:35pm 08.19.20 My internal halyard ended up at the top of the furler. No Jib for me. Forced me to try the asym spin |
||
Sink and cook top
Clive PC at 7:31pm 08.19.20 Yep, exactly what i did Ron, but i used the original stainless pin. I think i cut about 12-14 inches |
||
What qualifies as "advanced" when rating sailing ability?
DArcy at 7:21pm 08.19.20 Offshore racers go through this all the time. For the capability of the boat, you could point to the |
||
How do you store
HobieDog at 7:15pm 08.19.20 If I were to plumb both engines to a manifold and add an electric pump, I could pump directly into |
||
Somes Sound On MDI
HobieDog at 7:11pm 08.19.20 Wow! Have only experienced the area from land, and it's been at least a dozen years... We're doing |
||
Sink and cook top
Ron20324 at 6:53pm 08.19.20 Please shoot some pics of your table mod Sounds like what I did on my boat. I raised the table as |
||
Sink and cook top
Clive PC at 6:48pm 08.19.20 Okay i will next time I'm at the marina. Actually i have many more mods including sailing mods so ma |
||
What qualifies as "advanced" when rating sailing ability?
Kings Gambit at 6:41pm 08.19.20 Yikes! Y'all can set sail without me in those conditions. I'm staying in my nice, cozy, safe anchor |
||
Jib roller furling line block
Ron20324 at 6:21pm 08.19.20 An older West catalog has them as Lewmar Jamming Blocks. Mine are used to free the lines from being |
||
An invite to the GNBN - The Great Northern Boaters Net
Brian D at 6:16pm 08.19.20 Thanks for the info. I will add that to my website. 0800PT is the same start time of the Baja Net on |
||
Racing on Galveston Bay (1)
Bill19233 at 5:55pm 08.19.20 Me too, definitely take a Cobra if I could have just one sports car. But if I could afford both, the |
||
What qualifies as "advanced" when rating sailing ability?
dlochner at 5:44pm 08.19.20 Humans seem to have this innate drive to put things into boxes and categories. I've spent my profess |
||
What qualifies as "advanced" when rating sailing ability?
Michael Davis at 5:42pm 08.19.20 Yikes! Y'all can set sail without me in those conditions. I'm staying in my nice, cozy, safe anchor |
||
Battery Data
Davidasailor26 at 5:42pm 08.19.20 +1 for the 20 hour load test as a way to get the most accurate idea of the true state of health. I u |