Serving sailors online since 1997
 
 

Recent Topics

Oriental School of Sailing at 1:29am 05.11.05
Cal
2/1067
What is the bridge clearance height for a CAL 2-25?
Gerald Davies at 1:15am 05.11.05
4/1729
The compass on my 2001 H340 is loosing the internal fluid. Any ideas on who / where to fix it. Compa
Samual at 12:51am 05.11.05
10/1299
Does the body get used to conditions that cause sea sickness or is it something that will always hap
RichardL at 12:42am 05.11.05
2/935
Hi Gregg - I was not able to get out until yesterday to try my Power Tiller, as I am having trailer
Dave9990 at 12:30am 05.11.05
8/2875
What are your opinions regarding what's better for sail shape control on a genoa? Rope or wire luff?
seathumper at 12:03am 05.11.05
5/970
I just ran a Coast Guard Documentation check on my boat and found that there are over 145 "Endeavors
Steve at 11:49pm 05.10.05
2/767
I have a 1992 H28 and am installing a Raymarine 4000 wheel mounted autopilot. My pedestal guard doe
Gunter Meyer at 11:36pm 05.10.05
19/1228
Now that it has taken over the Boat US Stores it seems that West Marine is aggressively driving up p
David J.11350 at 11:34pm 05.10.05
8/4335
Okay, I checked the archives, but no luck. I bought a quart can of exterior varnish in preparation
doug miller at 11:09pm 05.10.05
5/1268
considering buying a 216, but concerned that the boat has a reputation for leaking at the mast. is
rob at 10:54pm 05.10.05
3/941
I've been wondering, my sailboat has the 8hp yanmar, it came with no instructions at all. While sail
david5583 at 10:20pm 05.10.05
0/735
I Have an Oday 222. According to the instructions with the Loos tension gauge,the shrouds should be
Tim R. at 9:44pm 05.10.05
16/1215
I am a big fan of DIY. I love the satisfaction of doing things myself and if I save a little money
Jim at 9:36pm 05.10.05
1/854
Quite often I have experienced a problem with the transmissionin our 34 Hunter engaging when I would
Rich L at 8:06pm 05.10.05
2/965
Since I added a solar panel on my stern pulpit, I've had problems with my Autohelm ST 1000 tiller pi
Mike at 3:26pm 05.10.05
5/883
I notice that a few people have posted notes recently refering to their new 91S and was wondering if
Danny4719 at 1:55pm 05.10.05
5/934
After ordering and receiving 4 portlights from Sailnet, I finally had the time to install them. The
Doug at 1:14pm 05.10.05
2/1625
You folks were great with my last question now where do I find parts for the Renault RC8D engine. Sp
rkssail at 12:48pm 05.10.05
6/901
I am new to this site and also relatively new (starting 2nd season) to my 1986 Hunter 34'. I have a
Richard McDonald at 12:23pm 05.10.05
6/1312
Just finished servicing the old Hyde Streamstay furler and was wondering what the correct backstay t

Recent Replies

Close call?
Jackdaw at 6:45pm 04.05.21
The new tack was quickly higher than the one we came over from; kind of a hard left from a broad re
Flexible Solar Panel on Bimini - Backing?
sesmith at 6:40pm 04.05.21
We used 3M dual lock on our panels the last couple of years. My wife sewed the non stick dual lock
Engine block de-rusting question
dmax at 6:40pm 04.05.21
A new pan would be simpler and better, you could also try to locate the drain at the rear of the pan
Cutlass bearing strut set screws
Hayden Watson at 6:21pm 04.05.21
My 88 did not have set screws... but it does now!
Thinking about painting my hull
SailingLoto at 5:48pm 04.05.21
I forgot the pic
Thinking about painting my hull   (1)
SailingLoto at 5:47pm 04.05.21
Stripes are off, ready to pull hardware and start wet sanding tomorrow.
Thinking about painting my hull
SailingLoto at 5:47pm 04.05.21
Stripes are off, ready to pull hardware and start wet sanding tomorrow.
1983 H30 Chainplates
sail sfbay at 5:30pm 04.05.21
Welcome to the forum!! Do not get bummed!! Every used boat boat I have purchased has had some issu
LiFePO4 conversion
heritage at 5:19pm 04.05.21
My original alternator charging setup was a dumb alternator output going to a 20 amp dc to dc charge
Engine block de-rusting question
LukeAvanti at 5:16pm 04.05.21
Whew... raising the engine - and realigning it to the shaft - is beyond my skill level. And the boat
Thinking about painting my hull
SailingLoto at 5:09pm 04.05.21
@SailingLoto beautiful boat, got a color picked out? Kubota orange with a black stripe.
Beneteau 373 Single Handing
Davidasailor26 at 5:08pm 04.05.21
I think he means he bought a new furling mainsail that has vertical battens. Greg Yep - A conven
mast wiring q's
fred1diver at 4:58pm 04.05.21
just the connectors left to do, both lights are in working order and installed properly.
Compac 16 owner
rgranger at 4:50pm 04.05.21
Welcome aboard! Good sailing boat. A friend of mine sailed his all over the gulf coast.. I agree
Fan Belt/Impeller
higgs at 4:44pm 04.05.21
If you have lost one of the vanes on the impeller and it is restricting flow, you will continue to r
Beneteau 373 Single Handing
Tally Ho at 4:32pm 04.05.21
Jose Pla - I am very curious to learn how you you replaced a mast furling main with a conventional
Fan Belt/Impeller
Monterey385 at 4:17pm 04.05.21
With 500 hours on the engine, the heat exchanger should be fine, unless a piece of impeller, etc.,
Not really a question, but a thanks!   (1)
NINEv2 at 3:54pm 04.05.21
192424 Things are starting to come together. Fresh out of the box and looking for a permanent home.
Fan Belt/Impeller
Tom J at 3:39pm 04.05.21
We'll see whether the heat exchange is an issue once I have all of the new stuff in but I kinda thi
Window films   (1)
Ralph Johnstone at 3:32pm 04.05.21
How are you attaching to the boat? Dab of sealant and you're finished (almost).

Copyright 1997-2026 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.