oday 20 carver
at 2:13am 04.11.05
0/952
I have an O'day 25, new to me. Stepped the mast this weekend and noticed 2 cracks in the base of th
|
||
Scott
at 2:03am 04.11.05
1/2042
I'm replacing the forward hatch on my 25.5 this weekend. It is pretty much a direct replacement hatc
|
||
Dwight Thomas
at 1:47am 04.11.05
4/1057
I am interested in re-inforcing the motor mount area of my Oday 25 transom. I have the standard mot
|
||
bgcampbell
at 1:44am 04.11.05
7/1247
Looking for suggestions for a wax to use on my 170. I've searched the archives, and it seems that m
|
||
Kyle
at 1:37am 04.11.05
1/972
I need to re-form my upper and lower rudder bearings. I have researched the proper repair and am co
|
||
Pat Shannon
at 1:36am 04.11.05
2/958
Mast Raising thoughts for the 25(in water)
|
||
Harry
at 1:21am 04.11.05
5/889
I have a Yanmar 2GM20F. Yesterday I noticed dripping from the weep hole in the seawater pump. I repl
|
||
John S
at 1:19am 04.11.05
0/668
I had a 5 hour sail yesterday, it was great conditions blowing 20-25. I was alone so I was able to h
|
||
Rich L
at 12:58am 04.11.05
0/708
I need to move my outboard remote control from the rear vertical surface of the starboard cockpit se
|
||
Colleen Eichmann
at 12:44am 04.11.05
6/812
I recently purchased an O'Day 322. Since I've owned the boat I have not been able to run the engine
|
||
David10310
at 12:39am 04.11.05
3/826
Spring is here and it's time to begin the process of painting the bottom of my Hunter 31'.My quest
|
||
Tony5898
at 12:24am 04.11.05
5/1014
Any suggestions on a 12 v radio with CD changer for marine use - my budget is $75. I'm not sure if
|
||
bill R
at 12:17am 04.11.05
7/947
I would like to add roller furling to my new 25. Any advise as to what make, model and price would
|
||
Dave
at 11:31pm 04.10.05
11/3919
Can anyone give me some suggestions about getting the single line roller furling (on a Hunter 326) t
|
||
Tom Roberts
at 11:24pm 04.10.05
9/1148
It was windy enough that I reefed the mainsail at the dock befor departing. Once out of the marin
|
||
pimerese
at 11:07pm 04.10.05
0/802
I am in the position of having to change out the navigation electronics in my 1985 Hunter 31. The o
|
||
Lou 14643
at 11:00pm 04.10.05
5/1304
Dear all:I've posted this here a few weeks ago, but have a little bit more information about my O'D
|
||
Rob
at 10:50pm 04.10.05
5/1160
Good Morning Peggie,A while ago I asked you some questions about installing a prefilter in our head
|
||
Richard
at 10:30pm 04.10.05
3/1157
Greetings,What is the wisdom regarding a passage from Woods Hole to Newport? We are delivering ou
|
||
John Burns
at 6:08pm 04.10.05
2/1201
I have a 2002, 356 with Raymarine instrumentation.In 2003, and 2004 the Hunter dealer had to repla
|
Stink Boat
markwbird at 8:30am 09.23.20 Perhaps time to pull the fastenings and remove all the sole sections. We have done that in the past |
||
Windlass Seized Clutch
Terry Cox at 8:27am 09.23.20 Our boat has the same Maxwell windlass. What happens when you completely release the knurled face pl |
||
Sailmakers
markwbird at 8:27am 09.23.20 Sails from a good local sailmaker will, in most cases, be considerably more expensive as they should |
||
Windlass Seized Clutch
Kings Gambit at 8:14am 09.23.20 Also. If you can, remove all the stuff out of the way and increase (extend) the lever arm length (to |
||
Windlass Seized Clutch
Kings Gambit at 8:07am 09.23.20 When stuff like this happens to me I use the Ace heat gun on high setting to heat and then let cool |
||
Windlass Seized Clutch
HandsOnTech at 8:05am 09.23.20 Yes, that was my first thought. Unfortunately, the impact wrench requires room to swing a hammer. As |
||
Engine shut down, stuck in FWD
JoeWhite at 8:02am 09.23.20 Disconnect the propeller coupling from transmission and try starting with lowest RPM. Is the primary |
||
Tank Monitor
Rick at 8:01am 09.23.20 Give some info man! Tank? That couldnt be any more vague. Most of us love troubleshooting here so |
||
Assortment of cheap fixes on Cat 22 (2)
Jacktar at 8:01am 09.23.20 Couple of pix at Marina one just before alleged arrival (in the gulf we get effects 2 days before la |
||
ProNautic 1230P installation in Beneteau 331
helmfam at 7:59am 09.23.20 My B373 has no bonding, as do most if not all Beneteaus. Looks like you can just connect to the neg |
||
Engine shut down, stuck in FWD
kloudie1 at 7:55am 09.23.20 or ya caught a big bunch of line or net in the prop. |
||
Sailmakers
FastOlson at 7:54am 09.23.20 One caveat: whatever else you put into the information 'mix' for choosing a sailmaker, avoid the wor |
||
Windlass Seized Clutch
kloudie1 at 7:54am 09.23.20 Windlass would have to come out to be able to get hammer swing room.. Ya might try a wide blade stub |
||
Windlass Seized Clutch
rgranger at 7:22am 09.23.20 At some point you are going to have to go for it but I think penetrating oil is the right approach. |
||
Sailboat outboard 4 hp hanger Bemer
rgranger at 7:17am 09.23.20 ... was left to a raccoon for twenty years best I can figure. thnx. I once acquired a Mac V22-2 o |
||
Sailboat outboard 4 hp hanger Bemer
jssailem at 6:58am 09.23.20 You can always find another bolt. If too stubborn grind it off. I wonder why you are removing the o |
||
1991 - 28: Bulkhead Delamination?
jssailem at 6:55am 09.23.20 David, If this is an expensive purchase for you, it might be time to get a professional opinion to |