Dr. D
at 12:38pm 09.07.20
5/1244
As you can see from the pictures below, the grey hull of my 35.1 seems to have some faded area. I do
|
||
SlideRule
at 10:35am 09.07.20
3/901
|
||
rbaevergreen
at 9:48am 09.07.20
2/747
I'm working on fixing up my new-to-me 1962 Rhodes 19 centerboard. The previous owner said it almost
|
||
lokeypod
at 9:21am 09.07.20
5/2551
Hello, new 1969 Cal 29 owner here! Hoping someone can point me in the right direction. I have been
|
||
Mikem
at 8:38am 09.07.20
3/379
From left to right. My daughter in her new to her 1984 H37, Harmonic, me in our 2003 H466 Wings of G
|
||
lawyer33.7
at 7:38am 09.07.20
1/1152
|
||
rpludwig
at 6:25am 09.07.20
0/569
some good C22 info here, especially on Ruddercraft... https://www.catalina22.org/index.php/download
|
||
Jan Z
at 5:33am 09.07.20
1/790
I have a 1975 Columbia 26 MKII with a crack along base of port side locker and would like ideas on h
|
||
idouglas1304
at 11:47pm 09.06.20
1/1792
I am involved in a San Juan 23 restoration project at the Calgary Yacht Club in Alberta, Canada. I
|
||
idouglas1304
at 11:21pm 09.06.20
2/1190
Hello, I am involved in restoring a San Juan 23 at the Calgary Yacht Club in Canada. The wind indic
|
||
circledog
at 7:18pm 09.06.20
9/2003
Hello Everyone, hoping you Can give some advice on the boat. It would be our First sailboat. Our Pl
|
||
Weasel
at 6:17pm 09.06.20
0/7
|
||
Weasel
at 6:12pm 09.06.20
15/1931
|
||
Greatdaner6
at 5:12pm 09.06.20
1/357
|
||
Rick
at 4:39pm 09.06.20
28/3083
Had an interesting trip to Catalina Island two weeks ago. Was a miserable crossing, probably the wo
|
||
Lewmar DC1 (1)
Drinky Crow
at 4:04pm 09.06.20
4/789
The "domino" ones. https://www.defender.com/images/secondary/DC_CLUTCH_2.jpg Anyone get slippage w
|
||
SonShine
at 10:48am 09.06.20
11/872
I'm just wondering.... My 1983 H22 has a door consisting of 4 slats of wood leading into the galley
|
||
gtg
at 8:01am 09.06.20
31/4614
Tomorrow, I skipper! Maiden voyage, 15 ish wind speeds. I am in a Catalina 22, 1974. I plan to start
|
||
wdonovan
at 6:34am 09.06.20
5/808
Issue is holding tank not pumping out. Did some research and census is to suspect tank vent first. M
|
||
Gman74
at 5:47am 09.06.20
8/1099
Anyone out there that could give me the measurements for height and width of compac 23 bimini frame
|
Anyone installed a Balmar Serpentine belt kit on their Universal M25?
Hayden Watson at 8:59am 04.21.24 There is more going on then was evident in the other images. Fingers crossed that Balmar steps up t |
||
Outboard gear oil.... Tohatsu 9.8
thinwater at 8:52am 04.21.24 Going to change gear oil for 1st time myself. Plain 80/90 wt or should I use gear oil made for mari |
||
New Electronics - Is this about right?
Scott T-Bird at 8:45am 04.21.24 1. He has a below decks motor drive for his autopilot. The red dashed lines in the drawing below |
||
Anyone installed a Balmar Serpentine belt kit on their Universal M25?
jssailem at 8:27am 04.21.24 There is more going on then was evident in the other images. Fingers crossed that Balmar steps up to |
||
Universal M25 front V-belt pulley.
Hayden Watson at 7:42am 04.21.24 Sold my C30 in 2017 and checking my notes it was 5.125 diameter. I think Balmar has made a mistake. |
||
Anyone installed a Balmar Serpentine belt kit on their Universal M25? (1)
Hayden Watson at 7:30am 04.21.24 Thanks for the link. If Balmar does not have the correct size of adapter, I will end up doing what |
||
Update on hose replacement, and follow-up question
chriscampbell at 7:12am 04.21.24 I'd fix it, but that's up to you. --Peggie So that hose should be shortened so that it only runs |
||
M-12 Oil Change
Randall Schmidt at 7:11am 04.21.24 my mistake, i was facing aft so you are right about me bei ng wro n g abou t starboard |
||
Outboard gear oil.... Tohatsu 9.8
dlochner at 6:50am 04.21.24 Use Marine Oil, it's not that more expensive. |
||
Update on hose replacement, and follow-up question
Peggie Hall HeadMistress at 6:40am 04.21.24 I'd fix it, but that's up to you. --Peggie |
||
Update on hose replacement, and follow-up question (2)
chriscampbell at 6:32am 04.21.24 That drawing from your manual only makes my case that boat builders are the WORST sanitation plumbe |
||
Grand Traverse Bay - destinations/anchorage recommendations?
john6206 at 6:12am 04.21.24 Leland is short trip from traverse city by car. But not by boat! Suttons Bay, Elk Rapids and nort |
||
Catalina 28 steering problem
Fred at 6:04am 04.21.24 I purchased my Cat28 MkII (2004) last year and immediately noticed that it pulled quite heavy to por |
||
Universal M25 front V-belt pulley.
Bob S at 5:36am 04.21.24 Sold my C30 in 2017 and checking my notes it was 5.125 diameter. I think Balmar has made a mistake. |
||
SUN - fascination (1)
JamesG161 at 5:23am 04.21.24 Solar Cycle 25 Power and Life on Earth. Stay tuned for the Sun's impact on ... Tropical Weather |
||
Anyone installed a Balmar Serpentine belt kit on their Universal M25?
Bob S at 5:22am 04.21.24 Have you spoken with Balmar? maybe they can exchange it. I installed their kit on my Beneteau and it |
||
Lifting strap blocking
JamesG161 at 5:12am 04.21.24 The Blocks were placed there for good reasons. 1) Windy Day Lift 2) Boat weight shift during lift 3 |