GregS
at 1:16am 08.15.05
1/877
What's the downside to leaving the rudder down between sails? It's a Ida rudder with no bottom pain
|
||
Scott
at 1:13am 08.15.05
1/6902
Looking for rigging instructions for minifish II
|
||
Steve
at 1:07am 08.15.05
3/850
I was out the other day running with the wind when I noticed that the main was being poked by the sw
|
||
John
at 12:54am 08.15.05
4/1042
I am thinking of chartering a sailboat with BVI Yacht Charters in February 06. Does anyone have any
|
||
Mike4116
at 12:46am 08.15.05
1/891
About 10% responded that their O'day sailed faster than 12 knots. Ahhhhhhh, haaa, haaa, haaa!Eith
|
||
RandleCorfman
at 12:36am 08.15.05
2/745
I have noted some smaller sailboats with windvanes atop the mast, and am interested in purchasing on
|
||
Steve Wallace
at 12:31am 08.15.05
0/655
I saw a Sovereign 7.0 on ebay that had a dodger, Anyone have a dodger for a Sovereign 7.0 for sale?
|
||
RandleCorfman
at 12:29am 08.15.05
4/2957
I just had a learning experience in uprighting my 14.2 capri after being caught off guard by a wind
|
||
Rich Woodward
at 12:21am 08.15.05
5/1351
I am curious if anyone has come up with a good solution for a bilge pump for the Hunter 27'. I curr
|
||
p323ms
at 12:17am 08.15.05
2/3109
Is it possible to get to Lake Dardanelle in a sailboat??? I saw a reference to a lock on the river.
|
||
Jack
at 12:11am 08.15.05
4/933
I looking for the "right" way to pick up a mooring ball, both when singlehanded sailing and with oth
|
||
Mike Jaeger
at 11:48pm 08.14.05
4/1011
Can anybody tell me what size. Also, has anybody usedTeflon impregenated Flax packing. Thanks in ad
|
||
Dan "Rode to Nowhere"
at 11:11pm 08.14.05
7/933
After 2 weeks in salt water, pin point rust spots seem to be starting on the stanchions. Does
|
||
Dave Myatt
at 10:59pm 08.14.05
3/855
Hi Recently, I discovered moisture and mildew in the v-berth between one of the cusions and the ar
|
||
jeff everson
at 10:14pm 08.14.05
0/709
i am purchasing a 50 hp tohatsu what pitch prop is best for crusing and which is best for pulling so
|
||
Ken Juul
at 10:06pm 08.14.05
1/1420
What is the recommended method for putting telltails on a in mast roller furling main? I've tried t
|
||
Sandpiper20958
at 9:54pm 08.14.05
2/1093
Dear Folks:I have a Schaeffer unfurling jib on a 30' Catalina. I purchased the boat last Spring.
|
||
Before the Bell
at 9:45pm 08.14.05
3/1038
I'm new to outboard motoring, I was a day sailor for many years and sailed a 16' boat w/o any utilit
|
||
John P
at 9:39pm 08.14.05
4/1124
When returning to the marina one night, I solidly hit something submerged. Once back out into clear
|
||
Lang Smith
at 9:35pm 08.14.05
10/1421
It was a sad day yesterday when my mainsail split in two on my 76 Oday 25. On the other hand, you ha
|
I win!
garymalmgren at 6:27am 10.26.20 If that system was good enough for Slocum it would be good enough for me. |
||
problems filling diesel tank
RoyS at 6:07am 10.26.20 Vent line must be located on top of tank at the highest point. Line must not dip down after leaving |
||
H41AC fuel level gauge just packed up!
jssailem at 5:55am 10.26.20 These are electrical signals being sent from the tank sensor to the gauge. First check is to inspect |
||
H41AC fuel level gauge just packed up!
shemandr at 5:55am 10.26.20 Those have been the subject of many threads. Bottom line is that they don't work very well. A sear |
||
Replacement Muffler for 1984 Hunter 34
RoyS at 5:34am 10.26.20 The muffler (Centek, I think) on my boat is nearly impossible to reach under the fuel tank. It has a |
||
Replacement Muffler for 1984 Hunter 34
kloudie1 at 5:24am 10.26.20 https://www.centekmarine.com/product-category/inline-mufflers/?pa_outlet-size=2&pa_inlet-size=2 |
||
Battery Sizing
RoyS at 5:17am 10.26.20 Another consideration for the future is your lighting. If you are still using incandescent lamps in |
||
Replacing Danfoss 101N0210 with 101N0212
buddybear at 4:40am 10.26.20 This is different than the low voltage. It's short cycling. And it can be caused by a few things: l |
||
Replacing Danfoss 101N0210 with 101N0212
JK_Boston_Catalina310 at 4:34am 10.26.20 JK Boston's comment is valid. Most of these controllers have a low voltage cutout. This is differ |
||
Replacing Danfoss 101N0210 with 101N0212
buddybear at 4:25am 10.26.20 I have had this failure twice. It is the control module -- an expensive, but easy, replacement. A |
||
Stress testing my hydronic heater.
Hayden Watson at 12:17am 10.26.20 I am not sure if that is stored in the computer or not. it is all handled by its internal ECU. The |
||
Replacement Muffler for 1984 Hunter 34
mnmpizza at 9:56pm 10.25.20 PO should have scuffed up the blue material a little better, might have held... my $0.02 |
||
Stress testing my hydronic heater.
Mark Maulden at 9:43pm 10.25.20 Do you know what the duty cycle for the Espar was? |
||
Replacement Muffler for 1984 Hunter 34
longnate08 at 9:05pm 10.25.20 Yeah the inlet and outlet have to be on opposite ends of the chamber for the muffler to fit the spac |
||
Lifeline autopsy
Hayden Watson at 8:25pm 10.25.20 The vinyl covers on my lifelines looked just as bad as yours and our local race rules do not allow v |