Serving sailors online since 1997
 
 

Recent Topics

sailor5017 at 4:41pm 02.03.21
3/670
have a leaky window on one of the side windows above the nav table. looks like it was assembled wit
Terry Cox at 12:30pm 02.03.21
8/1067
The week of February 15th has some promise for a mid winter cruise, weather permitting. So, think ab
Prairie Virgin Sailor at 9:39am 02.03.21
26/6630
I am a NEWBIE to sailing and am planning a pleasure sail from Gibsons to Nanaimo in the spring. Is
discovery at 8:48am 02.03.21
1/414
i have a 2002 passage 456, auto pilot control head is st 7000+worked flawlessly now for 16k miles bu
rgranger at 8:33am 02.03.21
36/5740
CYQK at 4:01am 02.03.21
2/554
Saw a good article on this place. Seems like a good destination. Anyone have any experience there?
Kevin&Karen at 5:08pm 02.02.21
3/712
Can anyone help us? We are looking for the stainless steel wing nut type securing latch that secur
Sullzarollz at 4:36pm 02.02.21
12/1004
Jskosmo at 3:02pm 02.02.21
2/582
OWI at 9:42am 02.02.21
4/715
For everyone looking to replace teak slats in the cockpit, i have created a short video on how i did
johnperri55 at 7:47am 02.02.21
3/1319
im going to have my dealer install a generator. i know catalina uses puma generators. i hear they ar
Bill19233 at 6:05am 02.02.21
17/1726
I'm way behind on "January sailing in Texas" videos. We left the dock for 10 races in January, only
sailme88 at 5:05pm 02.01.21
5/550
Yesterday I get word that my Hurth tranny isn't too bad. Needs a gasket and bearing kit. Today marke
sail sfbay at 4:59pm 02.01.21
2/1138
New 1984 boat to me has two (2) 30 amp and one (1) 50 amp shore power connections and NO galvanic is
Bowleys Quarters Catalina at 1:04pm 02.01.21
2/1417
hello working on a rehab Cat 22. need a bunch of things. mast plate, rudder tiller assy, cockpit cu
sf34dtw at 10:19am 02.01.21
16/2311
I currently have this anchor on my 2002 Beneteau 331 (see picture). It is a great anchor and I do no
CherylZZ at 7:09am 02.01.21
7/4102
In response to Don's message on fractional rigs and tell tails, I would like to know your opinion on
Future Boat Owner at 9:58pm 01.31.21
14/1825
Looking for a complete mast with standing rigging for a Hunter 430
snoopy_ at 7:11pm 01.31.21
6/861
Does anyone know the approximate length of sanitation hose required if I wanted to replace it all?
WDS at 1:50pm 01.31.21
0/14
This unit was bulkhead mounted on my recent purchase, think I must replace... Suggested options, thi

Recent Replies

Old whisker pole locking mechanism
R Squared at 1:48pm 11.02.24
The version of the whisker pole that you have is from the early 1970's. Since it is a three-section
Yanmar 3JH2E Commissioning run and lost all oil in an hour
dlochner at 1:35pm 11.02.24
I feel your pain. My oil pressure switch failed with nearly a gallon of oil in the bilge. At the tim
CNG Stove
Rich 35.5 at 12:52pm 11.02.24
I just made the conversion on a Legend 35.5. New propane stove and oven, with the 20# propane ta
CNG Stove
Alan Gomes at 12:18pm 11.02.24
an alcohol stove Make that, "non-pressurized alcohol stove." I like mine a great deal, by the way
Yanmar 3JH2E Commissioning run and lost all oil in an hour
Rafael8008 at 12:04pm 11.02.24
Follow-up from MAY 2023 The igmonius pressure sensor failed a second time. Exactly two sailing sea
DIESEL TANK GAUGE NOT WORKING - HOW MUCH DIESEL DO I HAVE?
Dalliance at 11:22am 11.02.24
Filling my tank is a two person job. It's a plastic tank and while someone pumps diesel I put a fla
Rebedding life line stanchions.
Ralph Johnstone at 11:09am 11.02.24
Welcome to the site. I know less than nothing about Morgans, but I do know that Hunters use a 3/8"
VDO Multifunctional Display: Batteries, water and fuel levels
doschhar at 10:20am 11.02.24
I then found a small 1 Amp fuse close to that connector on the distribution board and it had blown!
CNG Stove
dLj at 10:01am 11.02.24
Don't know what the boat is, but you may consider electric induction cooking or an alcohol stove rat
Experience with Por 15 tank sealant for aluminum fuel tank holding diesel?   (1)
mforum at 9:44am 11.02.24
Unfortunately, over the last 6 decades of boating, I've had more than my share of holy tanks. Obvio
Hunter 240 - replacing chainplates and deck fittings?
Slowboat314 at 9:40am 11.02.24
@Crazy Dave Condon I sent you my info via PM. Thanks!
Stuffing box wrench size question   (1)
Project_Mayhem at 9:17am 11.02.24
If your shaft is out, then I would look at FWD axle sockets which can be rented for free from Autozo
Full enclosure questions   (1)
Project_Mayhem at 8:50am 11.02.24
Here's an elaborate idea if the owner is really determined. The main sheet goes through a small sect
Escrow and Survey before seeing a Boat
Sailfanatic at 8:07am 11.02.24
I have a boat for sale and was contacted by a gentleman who wants to open up an Escrow account to h
CNG Stove
dlochner at 7:41am 11.02.24
Nor I! On a boat I am considering purchasing but this could be a deal breaker. The orifices may
Hunter 240 - replacing chainplates and deck fittings?
Crazy Dave Condon at 7:37am 11.02.24
@Slowboat314 There is a lot to discuss which is why I sent you a private message asking for your p
Escrow and Survey before seeing a Boat
Sailfanatic at 7:30am 11.02.24
Ralph's right. IIRC, BoatUS should have a "How to sell your boat" procedures and recommendations r
CNG Stove
sandpiper10471 at 7:23am 11.02.24
The replacement gas orifices may still be available,, we don't know the make/model of your stove.
Black tank overboard discharge....
JBP-PA at 7:12am 11.02.24
...and no Y valve either. Are you saying you don't have any Y-valve at all? It is always direc

Copyright 1997-2025 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.