Schwarz633
at 11:17am 11.10.24
22/1149
I'm doing some upgrades on my 1982 Tartan 33R and decided to draw out an electrical schematic to wor
|
||
FlyingMonkey42
at 7:49am 11.10.24
5/660
I just purchased a 78 35-1 in Florida. Previous owner pulled a few things out to lighten weight for
|
||
Mike Oldak
at 6:43am 11.10.24
34/2051
I'm about to upgrade my Raymarine autopilot from wheel drive to hydraulic drive. Has anyone connect
|
||
henri
at 4:06am 11.10.24
4/614
I cannot locate the rotary dial to regulate the temoerature on my fridge. I have a 42CC year 2003>
|
||
Screen Saver
at 7:46pm 11.09.24
5/564
Anyone replaced the cutlass bearing in their Hunter 49, and I guess the 50DS would be the same. The
|
||
zinahewitt
at 6:56pm 11.09.24
11/919
Hi All, Hope your weekend is going well. My Marine Fabric Seamstress was a little busy and had no t
|
||
sailcapt340
at 12:41pm 11.09.24
0/21
Finally going to replace and move my 2000 Hunter 340 VHF Radio from the pedestal to the navigation s
|
||
AndyL
at 12:38pm 11.09.24
1/307
228373 On my 2004 Hunter 36, the aft end cap on my port genoa track disintegrated and now the bolt
|
||
sailcapt340
at 12:38pm 11.09.24
73/4326
Finally going to replace and move my VHF Radio from the pedestal to the navigation station inside th
|
||
monocerosin
at 8:20pm 11.08.24
5/593
First motor out and back just wanted to share an update. Thanks to e:eryone here that helped out w
|
||
Idaho Islander
at 3:58pm 11.08.24
3/449
Has anyone on here sailed from St Croix to Galveston? I'm planning to sail my 41' Morgan there in J
|
||
coxwaine1
at 12:43pm 11.08.24
1/430
Hello all! First I want to say thank you for all the extensive information and all of your collect
|
||
LakeShark
at 8:10am 11.08.24
18/1926
Anyone else following the start of this round the world race this weekend? This and the Golden glob
|
||
jssailem
at 7:48am 11.08.24
0/518
29 October 2024. Our sun puts on a show celebrating the European Space Weather Week, which is takin
|
||
MFD
at 8:32pm 11.07.24
7/831
Anybody know the trick on removing this fixture to change the bulb? I was going to put a banana in
|
||
max_sailing
at 5:52pm 11.07.24
12/1649
Hello, Long time reader, first time poster. Over the summer I acquired 310 hull 238 here in Portla
|
||
spadaforaj
at 4:46pm 11.07.24
8/884
Hi - 2004 Hunter 41 with seldon in mast furling. Never worked right - but sail is probably stretche
|
||
Mickstr
at 4:24pm 11.07.24
4/444
I keep my 322 on a Mooring, and have a CQR I'd like to hang on the bow roller. However, due to the a
|
||
Jim Nortz
at 3:40pm 11.07.24
8/1308
|
||
Randy Miller
at 12:26pm 11.07.24
5/669
Hi...I have a 1987 Hunter 34' sailboat with a Yanmar 3GM30F engine in her. The last time I took the
|
Thru-Hull Replacement - How do I get through this mess?
BigEasy at 3:30am 06.12.25 Well, the only positive remark is that when you finish the replacement of this first valve assembly, |
||
Thru-Hull Replacement - How do I get through this mess? (7)
TrapperJohn at 1:10am 06.12.25 Well, I've finally gotten far enough to have some (but not all of the) answers. I started with the |
||
Belt adjustment on my Perkins M30 engine beneteau 351 (1)
Ralph Johnstone at 11:34pm 06.11.25 232109 If it's not the oil filter, it's something else back there. Mine requires a deep socket on |
||
M25 Rear main seal leak or...
Hayden Watson at 9:45pm 06.11.25 Given you have it out, a rear main seal would be prudent. Have you checked the fluid in the gearbox |
||
Janky outboard setup
AaronD at 8:31pm 06.11.25 My wonky system is semi-permanently attached, but works well for testing at home and for rinsing out |
||
Air Conditioner
kloudie1 at 8:30pm 06.11.25 The connections I am thinking of are at the back of the power Inlet socket, at the breaker panel bus |
||
M25 Rear main seal leak or...
kloudie1 at 8:24pm 06.11.25 Welcome to the forum! I am not very familiar with that engine but your picture shows a leaky rear ma |
||
Head plumbing diagram - pumping out to sea
PickledHerrings at 7:36pm 06.11.25 I have the exact same system on my boat with the exception that the raw water intake has no vented l |
||
Chart Plotter
Foswick at 7:04pm 06.11.25 That's classic stuff today. Buy out any small guys who actually innovate, and have become a threat |
||
Belt adjustment on my Perkins M30 engine beneteau 351 (1)
jssailem at 6:53pm 06.11.25 Kevin. Looks like the boat the end of the arrow is loose. wrench extension. https://www.amazon.com/d |
||
Anchor
kappykaplan at 4:13pm 06.11.25 I'll start my response with, Not another anchor thread! :facepalm: You're correct that there are man |
||
'88 Hunter 37 main traveler
Tally Ho at 3:28pm 06.11.25 I agree with @shemandr that the traveller is probably thru-bolted, but Hunter did build boats with a |
||
'88 Hunter 37 main traveler
shemandr at 2:51pm 06.11.25 While I don't know your boat I would expect the traveller would be thru bolted. |
||
Janky outboard setup
shemandr at 2:46pm 06.11.25 I came across a plastic barrel on a beach that someone had used for shotgun practice. It had shot h |
||
Amp draw question
JoeWhite at 2:02pm 06.11.25 Definitely remove the outboard when trailering. The bracket will break when you hit a bump. Ask me h |
||