|
Lauren
at 8:14pm 05.15.06
5/870
I replaced my 1 year old impeller (as I do every year) 2 weeks ago. New gasket also. This time, in
|
||
|
Mark Mynsberge
at 10:59pm 05.15.06
6/856
I am having trouble with my water heater leaking. The lines were leaking where they entered the hea
|
||
|
Mike
at 11:34pm 05.15.06
2/939
I am moving the bridge deck (cockpit) mounted traveler to the coach roof on my O'day 28. I have all
|
||
|
tlthurlow
at 12:03am 05.16.06
11/6775
I've got a new to me 1978 Hunter 25. The deck and topsides are in need of painting. Before I go to t
|
||
|
Mike
at 12:50am 05.16.06
5/973
Traveler move I am moving the bridge deck (cockpit) mounted traveler to the coach roof on my O'day
|
||
|
cavitating
at 12:14am 05.16.06
6/1986
What size boom tent awning should I buy for a Hunter 240?
|
||
|
Don Guillette
at 1:09am 05.16.06
4/1742
Starting this Friday I'll be off the air for a couple of weeks. Our new home is finally completed an
|
||
|
Traumaguard
at 1:36am 05.16.06
8/1431
I have a universal M 25 xpb in a Catalina 30. When I am in low rpms like any where under 1000 I have
|
||
|
colin hunter 335
at 2:23am 05.16.06
7/1132
I have the traditional two battery with the usual Off 1, 2, or All switch and each bank giving out 1
|
||
|
kai13227
at 3:00am 05.16.06
6/1314
Hi...I just bought a (first time) whisker pole to attach to our genoa, and I'm wondering how the b
|
||
|
Mike
at 4:28am 05.16.06
6/1460
So what about radar reflectors? I have been prowling the internet to learn something about these dev
|
||
|
gstetlerg
at 4:10am 05.16.06
6/1270
I am getting water into my ballast tank even when I don't want to (e.g., the fill valves are closed
|
||
|
brianc
at 3:54am 05.16.06
4/924
I want to order a pre made dodger from existing patterns for the frame and dodger. Any one know of a
|
||
|
Richard
at 3:05am 05.16.06
18/1556
Everyone knows that the Coast Guard most of the time try to do a good job. This is true in especiall
|
||
|
peterbud
at 3:03am 05.16.06
0/730
does any one have the measurments for the stays on a Oday 222
|
||
|
Amerigo
at 4:38am 05.16.06
1/839
I have a hunter 34 with the original pedestal I think its a meriman? Something like that. Does anyon
|
||
|
mikeg
at 4:48am 05.16.06
3/5422
I have a ranger 26 mk 2 fractional rig 1979 model and am looking for a PHRF rating. They want to giv
|
||
|
Karl
at 5:47am 05.16.06
4/1447
I just bought a 2004 Hunter 26 which was on the lot for a year. So, how should i adjust the shroud t
|
||
|
Frank7693
at 5:46am 05.16.06
6/1175
I will be cruising Lake Ontario for the summer and would appreciate any recommendations for anchorag
|
||
|
PrincessoftheLake
at 5:36am 05.16.06
3/891
I would like to know if it is possible to add additional/larger water tanks and holding tank on a 19
|
|
Irwin
sail sfbay at 2:50pm 06.15.21 Virginian.......congratulations on your soon to be new boat, if your sea trail and survey goes well. |
||
|
Hunter Legend 37 Broken Keel Box? or just façade.
shemandr at 2:46pm 06.15.21 Did you have a hard grounding? |
||
|
Question about Jib Furling System
Tally Ho at 2:38pm 06.15.21 Good morning , an educated guess would be an FF4 model. You don't need to replace anything . There |
||
|
Steering Cable Fell Off
Captain Larry-DH at 2:36pm 06.15.21 Another possibility if, heaven forbid, your rudder falls off, is to use the motor for short burst s |
||
|
Washdown pump location
sail sfbay at 2:34pm 06.15.21 Check valve stops backflow from the pump to mitigate loss of prime on the suction side unless you ha |
||
|
Yanmar 2GM20F Failure - reality check needed (2)
Ralph Johnstone at 2:24pm 06.15.21 The only problem I see in this description is running the engine at 2,000 RPM. The recommended RPM s |
||
|
Washdown pump location
Ken Cross at 2:22pm 06.15.21 Great question!! You have a good plan to supply the washdown pump from an existing through-hull fi |
||
|
Washdown pump location (1)
sail sfbay at 2:13pm 06.15.21 Great question!! You have a good plan to supply the washdown pump from an existing through-hull fit |
||
|
Yanmar 2GM20F Failure - reality check needed
Fredct at 2:02pm 06.15.21 Elbow was replaced in 2017. I will check. |
||
|
Yanmar 2GM20F Failure - reality check needed
Calif. Ted at 2:01pm 06.15.21 I'd check the exhaust elbow for clogging also. |
||
|
Yanmar 2GM20F Failure - reality check needed
Fredct at 1:43pm 06.15.21 Don, like a large piece of dirt obstructing the flow from the tank? I thought about fuel pump and |
||
|
Yanmar 2GM20F Failure - reality check needed
Don S/V ILLusion at 1:41pm 06.15.21 The only obvious possibility is a clogged pick-up tube in the tank but it could be lots of things li |
||
|
Solent Stay H36
Jim Legere at 1:39pm 06.15.21 The H37C didn't have a "factory cutter option" - it was designed by Cherubini as cutter right from t |
||
|
Paint for plastic portlight surrounds
flightlead404 at 1:33pm 06.15.21 I know there are plastics paints specifically for this purpose. I've gone down this road on a few a |
||
|
BELT DUST
twodzusfittings at 1:25pm 06.15.21 You should always use a grip notched belt especially when doing around a small pulley such as an al |
||
|
Hunter 240 Boom Traveler (3)
rgranger at 1:19pm 06.15.21 My 26 is the same. I actually like the position of the sheet attachement . I use it to pull up on |