ohpoppy
at 7:59am 06.09.06
1/1117
Would anyone know the best way to replace one of the 4 screws on the bracket that the 3 stays attach
|
||
Ron
at 8:41am 06.09.06
2/2128
I recently got a 18 foot Balboa sailboat and would like to find a operator manual or some manual for
|
||
Lew Slaughter
at 8:32am 06.09.06
1/886
I have to replace it again and would like a telephone number of a Mac parts place in Florida. Or th
|
||
shorty
at 8:31am 06.09.06
2/853
Could someone measure their hatchboards for me? I'm thinking of making a stow box for them for the l
|
||
Danny9462
at 11:53am 06.09.06
1/906
Can amyone tell me if a coach top travler system on a Hunter 27 will add to or hinder the performanc
|
||
sailgirl20776
at 11:49am 06.09.06
6/4399
We are sailing from Wickford, RI to Salem,MA and are looking for anchoring sites along the way. We a
|
||
Al
at 11:02am 06.09.06
1/950
Where can I get stainless steel hand rails to directly replace the original teak on the cabin of my
|
||
waybish
at 10:52am 06.09.06
0/730
Greetings!I am in the market for a MacGregor 26. I have seen the new 26M and am in the process of
|
||
Steve White
at 8:56am 06.09.06
6/2557
I'm interested in knowing what propeller size you Cal 2-29 owners are using with your Farymann A30 1
|
||
Scott
at 12:20pm 06.09.06
10/1128
My boat has a tendancy to point into the wind. Just prior to letting go, I can feel the rudder begin
|
||
Timm R 25 Oday
at 12:46pm 06.09.06
4/983
When tensioning the rigging on our 25 Oday I found all of the adjustment gone on the upper port shro
|
||
Joe
at 11:58am 06.09.06
4/815
I have an 89 26D and the mainsail looks like the line on the front of the mainsail (the on that hold
|
||
Chuck R
at 12:57pm 06.09.06
11/6205
While visiting with an owner of the same 222 O'Day that I have just purchased, I discovered that his
|
||
Charlie
at 1:14pm 06.09.06
4/3643
Can anyone advise what is the PHRF for a 272 sailng with and/or without a spinnaker? The boat is sa
|
||
Don Williams
at 5:56pm 06.09.06
11/2607
Where have all the recing gone??? I raced a 1994 35.5 with good success for several years before ret
|
||
Randy Church
at 9:13pm 06.07.06
3/842
After I have re-installed my reconditioned prop and new shaft is it best practice to fill recessed a
|
||
Bill Roosa
at 9:52pm 06.07.06
0/946
Had the occasion to go aloft to fix the anchor light and noticed a fitting on the mast I have never
|
||
Steve Braverman
at 11:28pm 06.07.06
15/2721
Have any of you been to Block Island? I am thinking of taking a cruise out there this summer with my
|
||
Mack
at 9:57pm 06.07.06
41/5287
Will be attending the Annapolis Sail show this year. Lots of new vessels and plenty on sales reps to
|
||
Capt.m
at 11:45pm 06.07.06
4/1081
I would like to get a pulse of owners with the Universal 5444 engine, on engine starting. It seems t
|
Hunter 260 Mooring Challenges
familyrapp at 1:56pm 04.16.21 Yes. Getting on the boat from both kayak and inflatable dinghy was always tricky. Got wet a couple |
||
Midship Cleat Location for '78 Hunter 27 (1)
Benny17441 at 1:50pm 04.16.21 Also removed the large bow cleat to install a claw anchor on a roller and substituted with two small |
||
Hunter 260 Mooring Challenges
isaksp00 at 1:47pm 04.16.21 I had our H23 on a mooring on a lake a few seasons. I started using a "toy" inflatable as a dingy bu |
||
Bottom Paint
Scott T-Bird at 1:47pm 04.16.21 Finally finished sanding down to the gel coat/glass and started to put on the first barrier coat. |
||
Bottom Paint (1)
dLj at 1:46pm 04.16.21 Finally finished sanding down to the gel coat/glass and started to put on the first barrier coat. |
||
What Gen 3 Anchors fit H38 bow rollers?
sail sfbay at 1:37pm 04.16.21 45 lb Manson Supreme on a Hunter 386. |
||
Midship Cleat Location for '78 Hunter 27 (1)
Benny17441 at 1:35pm 04.16.21 Cleats mounted on steel metal "L" brackets and bolted to the sides of the rail. |
||
Bottom Paint
FlimFlamII at 1:28pm 04.16.21 Finally finished sanding down to the gel coat/glass and started to put on the first barrier coat. A |
||
Hunter 260 Solar Battery Charging on Mooring
Stu Jackson at 1:27pm 04.16.21 Welcome. You could start with these: Solar Systems: Selection, Installation & Controllers by Main |
||
The Boat Exploded and Then I Died
wynkoop at 1:24pm 04.16.21 I am making new grab rails for my ericson 27. Those will be black locust, so the plan is to use the |
||
Fuel Filter Question
Benny17441 at 1:17pm 04.16.21 Like Stu indicates, the location of the filter is incorrect. Given this and the fact that it seems |
||
Do all Hunter 34s have a false bilge?
Benny17441 at 12:43pm 04.16.21 Let me warn you that there will be water already trapped under the sole of the bilge. As a matter |
||
Swing keel vs Dagger ?
RussC at 12:33pm 04.16.21 Maybe I'm a "tad" biased because I own a Mac 25 ;), but that 26d that rGranger posted is a screaming |
||
rudder rigging question
wynkoop at 12:14pm 04.16.21 Great looking tiller! Yes the spacing looks right for a tiller tamer. Never had one on my Ericson. |
||
PROP upgrade size
Benny17441 at 12:07pm 04.16.21 Check with the 3 blade prop manufacturer, as they usually keep conversion data for their propellers. |
||
Swing keel vs Dagger ?
rgranger at 12:02pm 04.16.21 the Macs are pretty simple. Not much to go wrong except for abuse. Motor and sails are the expensiv |
||
Removing Liquid Electrical Tape
rgranger at 12:01pm 04.16.21 If it is actually vinyl, any strong caustic will break it down to dust. Experiment with some (off t |