Doug
at 4:33pm 04.19.06
3/1000
I need 2 Stanshion's for my 1985-37C,Hunter can't help,anyone know of a source,thank's,doug.
|
||
Jim
at 7:26pm 04.17.06
11/1357
Anyone care to weigh in on whether or not 50' of chain equates to more than 50' of 3 strand when com
|
||
tony z
at 9:53pm 04.17.06
1/1273
I use a diverter valve to go either in the holding tank or to the thru-hull. The holding tank ca
|
||
Larry
at 9:56pm 04.17.06
1/1733
Can anyone provide this forum with updated information on the anchoring restrictions that were impos
|
||
Stuart Casteel
at 9:56pm 04.17.06
7/763
Hi, I was wondering what might be the best product to remove the light brown stains that travel the
|
||
Wind Dancer24482
at 10:46pm 04.17.06
4/2232
Can anyone give me a step by step replacement process for the line that is reponsible for holding do
|
||
L. Steimel
at 10:36pm 04.17.06
10/825
I have a Hunter 240. It is a 2000. It had numerous blisters on the bottom and also on the swing keel
|
||
Rich18826
at 10:29pm 04.17.06
0/797
I would like to thank the members of this forum helping with successful maiden voyage of the S/V Idl
|
||
emmettnevel
at 12:26am 04.18.06
5/1018
I need to remove the skeg in front of the rudder. Has any one done this? Do I have to drop the rud
|
||
Larry
at 12:37am 04.18.06
1/1835
The roller furling installed on my Morgan 382 is a Stream Stay furler made by Hyde Products of Cleve
|
||
Mark Mynsberge
at 1:10am 04.18.06
5/821
I plan on replacing my halyards this spring as a couple are showing wear. What I don't know is if t
|
||
Bob
at 1:40am 04.18.06
4/822
I have a 1982 Hunter 37' cutter in need of a re-do of the Anti-skid Paint..............Does anyone
|
||
MtHawk
at 1:53am 04.18.06
4/13188
Does anyone know what interlux special thinner 216 really is. I want to bottom paint my boat and it
|
||
THE LAUNCH (1)
Rick Ellis
at 2:06am 04.18.06
14/879
EASTER SUNDAY
|
||
Traumaguard
at 2:21am 04.18.06
4/1146
Time to buy new sheets and halyards. What do all of you reccomend? I bought a C30 and it came with n
|
||
Stuart Casteel
at 2:20am 04.18.06
14/988
I am in the process of tuning my rig and all things look good except for the back stay. I have the m
|
||
Randy
at 2:23am 04.18.06
2/1008
The sheeves on my two jib sheet blocks have disintegrated. These are the kind that stand up, mounte
|
||
Kimmo
at 2:39am 04.18.06
8/1253
Hi all: So anyone know a website that shows the average weather conditions for particular times of t
|
||
SouthernCross
at 3:03am 04.18.06
2/1355
I am in the process of trying to find and install a mast collar on my 37 cutter, so I can run my out
|
||
chiefjgreene
at 3:28am 04.18.06
2/939
I have just brought home an 86 Hunter 23. It has the Kenyon mast and boom. The previous owner ran th
|
Moving chainplates outboard
sailme88 at 2:38pm 12.14.20 Wow ! Would you be changing out your spreaders? How would you deal with the old chain plates? If |
||
37C Windlass
Angus Fleming at 2:26pm 12.14.20 Bolander You asked about drainage in the locker forward of the v berth. My H37c has a windlass in th |
||
Depth gauge vs Chartplotter
jssailem at 2:23pm 12.14.20 Sounds like you need a dock friend with a ray marine system to take your display and plug in to thei |
||
Guide-on assist for trailer....
Project_Mayhem at 2:20pm 12.14.20 The PVC looks professionally bent! |
||
Universal Kubota water pump failure.
ggrizzard at 2:09pm 12.14.20 What do you mean "Michigan shut them down "? |
||
Guide-on assist for trailer....
MikeJB at 2:07pm 12.14.20 Looks good! Did you heat up the PVC to create that bend or is it it just held in place by the bolts |
||
Guide-on assist for trailer....
Project_Mayhem at 2:00pm 12.14.20 Looks good! Did you heat up the PVC to create that bend or is it it just held in place by the bolts? |
||
Beneteau 361 Stanchions Loose
gearFX at 1:56pm 12.14.20 I don't see the stanchion wobble as being a problem. If someone falls agaoinst a stanchion of 1 inc |
||
Depth gauge vs Chartplotter
dave_and_dd at 1:54pm 12.14.20 Hi thanks Jssailem, I know it is possible to connect a xducer without the raymarine instrument. My |
||
Beneteau 361 Stanchions Loose
Ron20324 at 1:52pm 12.14.20 The stanchion bases on my 323 are like those in post #6 above. The bases do loosen up over time and |
||
Non-skid gelcoat mold for 1984 Hunter 31
jrmellin at 1:41pm 12.14.20 Thanks all for the help! The 102 GFD pattern is the one Gibco and the Forum Store think it is. I'l |
||
Anyone have pics of mast lowering Bridle attachment?
isaksp00 at 1:41pm 12.14.20 Also, don't underestimate the forces on the mast when part way down. I would never consider moving t |
||
Anyone have pics of mast lowering Bridle attachment?
isaksp00 at 1:37pm 12.14.20 That last photo seems to be a form of halyard restrainer. Your forestay mounts very close above the |
||
How do you break in an outboard on a sailboat?
Meriachee at 1:19pm 12.14.20 Its all moot. A 26c will only plane on the trailer, and the Honda wont have anything to do with tha |
||
COVID Testing
Ralph Johnstone at 1:06pm 12.14.20 Yet? Yes, I guess that ship's already sailed :wahwah: ! |
||
Guide-on assist for trailer....
MikeJB at 12:45pm 12.14.20 That's some creative work - looks good. How did you bolt the lengthwise ends of the PVC to the 2 s |
||
Catalina 34 dodger
neshanic-nj at 12:35pm 12.14.20 Thanks for all the input. It's good to have a general idea as I start shopping. |
||