bill rau
at 11:38pm 06.20.06
0/873
I am refinishing the wood trim and between the side panels and the deck is a long strip of rubber-li
|
||
Don s/v Tellico
at 10:42pm 06.20.06
16/1416
After all the dicsussion here about the merits of lifejackets, falling overboard, etc., and the hour
|
||
steve L5538
at 10:36pm 06.20.06
1/929
This is a repost of my previous message because I realized I'd neglected to put that it was specific
|
||
Janne
at 10:35pm 06.20.06
1/2074
Hello,Anyone have any experience in mounting a Dinghy Davit on a Hallberg Rassy 53?Where can I fi
|
||
Smitty
at 10:55pm 06.20.06
3/942
I am installing a Raymarine E80 with GPS, Radar and fishfinder. My old Radar was mounted on a Quest
|
||
colin hunter 335
at 2:27am 06.21.06
5/1487
The back stays on my h335 (1989) are bottomed out and I am still a little slack on my rigging. How
|
||
Dave19333
at 12:44am 06.21.06
10/1051
I have been sailing on the Chesapeake Bay with my H23. We have a great time but the boat is too ligh
|
||
mike
at 12:37am 06.21.06
5/1128
I am new to sailing and wanting to learn as much as possible. One question I have is about head sail
|
||
Ross Anderson
at 12:36am 06.21.06
2/1058
I'm looking to talk to any 80-82 36 Hunter owners.This John Cherubini designed Hunter is famous for
|
||
tadd5181
at 12:34am 06.21.06
2/1073
The B'G autopilot on my Hunter 420 fell out of commissioning and won't accept a new commissioning (w
|
||
Karl
at 11:53pm 06.20.06
5/3988
Can anyone tell me the diameter and length of rope needed for the main sheet, main halyard, and jib
|
||
Chuck
at 11:42pm 06.20.06
6/1473
I have an older Envinrude ouboard, and the throttle does not stay in position, requiring you to keep
|
||
AXEL
at 4:18am 06.21.06
13/1372
Has anyone here done this? From what I can gather, all I should have to do is connect the brown wire
|
||
KennyH
at 5:02am 06.21.06
8/10116
My battery has a switch to disconnect all connections while at the dock and not being used. Only th
|
||
walmsleyc
at 5:37am 06.21.06
3/926
I've just purchased a Hunter Legend 35. The bilge pump thru hull exits from the port side storage c
|
||
HueyDr
at 5:47am 06.21.06
10/1107
I have been actively looking for a 25' Catalina for about 3 months now and, like an idiot, only yest
|
||
alymar
at 6:00am 06.21.06
4/903
I just purchased my boat and it came unrigged. I've had sail boats before but would like to see a of
|
||
rvh3
at 6:12am 06.21.06
2/1500
I'm a brand new owner of a 1986 Catalina 30 that unfortunately has a broken throttle lever. I've tr
|
||
Mike
at 6:12am 06.21.06
10/1126
I am installing a deck traveller on my O'day 28 this weekend. It is a Garhauer unit complete with ri
|
||
NautiDuck
at 6:19am 06.21.06
4/1780
In the archives there are quite a few posts about the Origo alcohol stoves but not about the portabl
|
sail cover: Clips vs twist lock fasteners
Mark Maulden at 11:27am 12.30.20 I use twist locks on straps to leave the bottom open. The twist locks are unlocking themselves over |
||
How to prime house water pump
Berkeley 30 at 11:26am 12.30.20 How long do you expect the pump to run before you have full pressure? Also, while the pump is runn |
||
How to prime house water pump
Berkeley 30 at 11:23am 12.30.20 All potable water pumps that I am aware of are self priming. Most are diaphragm and if they do not |
||
How to prime house water pump
Berkeley 30 at 11:21am 12.30.20 You don't mention what sort of water pump,you have, but I think you just need to run the pump until |
||
Enlarging hole in hull?
dlochner at 11:12am 12.30.20 There are a couple of ways as @sesmith mentioned. The tool to use is a hole saw. If the hull is thin |
||
Enlarging hole in hull?
Allan12210 at 11:08am 12.30.20 Here is a link to my post when I enlarged my raw water intake through hull. I used two hole saws; on |
||
Motor mount
PDW at 11:05am 12.30.20 Was looking at owners manual. 5-8 hp recomended for a 240. Need to find what that means in weight. |
||
Winterizing diesel fuel on boat
Guan at 11:05am 12.30.20 tks to all very fast info as usual..... will do. |
||
Winterizing diesel fuel on boat
Guan at 11:03am 12.30.20 Good to hear from you @Guan. Hope you are doing well. Happy New Year. hey Jss a very immobile year o |
||
Battery bank
PDW at 11:01am 12.30.20 Gas fumes and electrical together in that fuel locker is a fire and explosion waiting to happen I |
||
Oh the Weather outside is frightful...
seanmadian at 10:56am 12.30.20 Oh my... you could be in for a treat is you are not vegan.. Imagine if you will a long difficult s |
||
Enlarging hole in hull?
sesmith at 10:55am 12.30.20 Cut a plug for the hole the right size with your hole saw from a piece of wood. Glue it into the hu |
||
Oil change... Make it a double
jssailem at 10:47am 12.30.20 Go for it... Someone in need can use the recycled oil. |
||
Oh the Weather outside is frightful... (1)
jssailem at 10:39am 12.30.20 Oh my... you could be in for a treat is you are not vegan.. Imagine if you will a long difficult sa |
||
OK- on this the third day of Christmas- what did your true love bring YOU ? :)
Leeward Rail at 10:38am 12.30.20 No official gifts this year. That said, my amazing wife: - makes me perfectly prepared Cappuccinos |
||
sail cover: Clips vs twist lock fasteners
Roland5048 at 10:35am 12.30.20 The buckle+straps are nice and quick, plus allow leaving them loose if needed, to give better venti |
||
sail cover: Clips vs twist lock fasteners
dlochner at 10:34am 12.30.20 I've always used twist lock, aka common sense, fasteners on the bottom of the cover. Don't see a nee |