Serving sailors online since 1997
 
 

Recent Topics

djletin at 11:46am 12.22.20
0/25
looking for used Catalina/Capri 18 located at New Jersey shore. ...Dan (djletin@verizon.net, 732-2
swshogren at 10:54am 12.22.20
5/904
Hi again with more questions as I did further into our new to us Hunter 34. When I look at the mold
Top Crew at 10:22am 12.22.20
7/894
Hi folks! I recently bought a year 2000 Benetau Oceanis 461 that at the moment the rudder was down f
Alansails at 10:10am 12.22.20
6/1508
themotorman at 7:57pm 12.21.20
10/1296
I am refurbishing a 28 Columbia. it has wire halyards. I see that some users like all rope. What are
Driftin II at 6:59pm 12.21.20
4/724
My boat is on the hard an hour drive away. I've decided repacking my stuffing box before launch in t
Boomtown at 5:44pm 12.21.20
12/1707
I recently replaced the hot water heater on my B331. Now the freshwater pump has started to run all
Toby1979 at 4:59pm 12.21.20
1/680
what did Beneteau use for the finish on their folding cockpit tables on the 473's? I have hull #7 (
patrickkidd at 2:36pm 12.21.20
10/1406
I have a J/30 in (Seward) Alaska. To the extent possible, I am looking to replace a Webasto heater w
Ziggler at 12:54pm 12.21.20
23/3374
Electrical question as I develop a power use chart. Best guesses for watts (or 12V amps draw) of the
Jay Chase at 10:10am 12.21.20
18/1791
Thaniel at 7:58am 12.21.20
112/13955
Hello Everyone. I've spent many hours reading this forum and there are a lot of good people and inf
Samurai at 9:12pm 12.20.20
4/904
Greetings Brand new to this forum so that I apologize in advance for any errors in protocol. Seeking
ricksoth at 1:15pm 12.20.20
33/6592
Hello all, I plan on storing my Cal 27 during the Spring-Fall period each year on a helical screw m
CowboyWay at 12:48pm 12.20.20
3/665
The floor panel that covers my C310 bilge has separated. I tried rescrewing the 3/4" marine plywood
jssailem at 12:43pm 12.20.20
3/379
joecool911 at 11:03am 12.20.20
30/2880
Where have you guys purchased new main sails? Are the ones from here made by Doyle upgraded any sin
Kings Gambit at 6:41am 12.20.20
35/1716
Hi all, The astronomical event of the past four centuries will occur on December 21, the winter sols
BlowMeAway at 7:22pm 12.19.20
7/688
rnEqv8WcVq8 Merry Christmas
Member 131497 at 1:19pm 12.19.20
16/1466
Hello again to all... here are 2 photos of the edge of tbe companion way hatch. the inside edge, bor

Recent Replies

trailer my boat to florida
Captain Larry-DH at 4:31am 05.10.24
my prized little BMW Z3M in Imola Red Sweet!
Stuffing box mount repair
mbefus at 3:58am 05.10.24
The boat was given to me so I skipped the survey. I was able to access it through the port lazarette
trailer my boat to florida   (1)
Tally Ho at 8:31pm 05.09.24
I can only imagine who they could get to do it for under $400. Or maybe they use it as a mule for
trailer my boat to florida
rgranger at 6:39pm 05.09.24
My daughter had her car hauled from Charleston South Carolina to Los Angeles California. And it was
Dropping rudder on 11.0A
shemandr at 5:34pm 05.09.24
Got the rudder off, had to chip away at the skeg boot for about 4 hours. Used a heat gun, chiseled,
H49/50 Boom Preventer Rigging
Zencra at 5:23pm 05.09.24
on our 49 I use a low friction ring/dyneema loop run through the forward mid cleat and back to prima
H49/50 battery replacement
Zencra at 5:13pm 05.09.24
I fitted 6x100 a/h Battleborn LifePo4, they went in perfectly with room for 2 more if needed. Go Lit
hunter 49 wing keel dimensions?
Zencra at 4:50pm 05.09.24
it's ok I ended up diving, it's just under 4.5 ft wide.
WATERLOCK MUFFLER QUESTION
twodzusfittings at 4:37pm 05.09.24
Agreed Greg. Wasn't going to stir the pot, but then we could say that about half the posts on this s
Stuffing box mount repair
Mark Maulden at 4:36pm 05.09.24
congrats for your new boat! I have two questions. 1) did you have a survey prior to purchase? If s
Dropping rudder on 11.0A
Tally Ho at 3:53pm 05.09.24
I think you are going to have to clean out the boot to get rid of the old fiberglass and glue, and r
Whale Manual Bilge Pump
JamesG161 at 3:50pm 05.09.24
Or you can make your own O-Rings with this kit. https://www.amazon.com/Buna-N-Ring-Splicing-Duromet
Rudder crack   (1)
mbefus at 3:44pm 05.09.24
Cut into the rudder and the entire stainless steel frame was corroded, and as the original commenter
O'day 23-2 Topping lift   (1)
Tally Ho at 3:41pm 05.09.24
Dropping rudder on 11.0A   (1)
mbefus at 3:36pm 05.09.24
Got the rudder off, had to chip away at the skeg boot for about 4 hours. Used a heat gun, chiseled,

Copyright 1997-2024 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.