Emee
at 2:08am 08.10.06
8/959
I have a Hunter 33, 2005. I have noticed when I sail over the 4 knots the prop freewheels and virbra
|
||
35' O'Day Owner
at 1:37am 08.10.06
2/1072
Am looking for design related information for my 1986 35' O'Day. Was this an O'Day design or other,
|
||
Don Williams
at 1:08am 08.10.06
3/784
Hello, Planning a cruise to Rio Dulce, Guatamala in mid to late November 06. I am having trouble f
|
||
David W
at 12:37am 08.10.06
11/1500
I would like to clean the engine in our boat but am afraid to do this using an engine degreaser that
|
||
joe staples
at 12:28am 08.10.06
0/813
On my 1974 Widgeon I have two lines that I guess raise and lower the CB. How should these lines be r
|
||
bart5008
at 12:14am 08.10.06
2/915
I posted a note about stern seats and teak. I have gotten a lot of info. on how to finish teak. Sugg
|
||
Phil Herring
at 12:00am 08.10.06
5/980
Found this photo on another board I frequent; it was begging to be posted. :)
|
||
Michael
at 11:41pm 08.09.06
17/3613
As mentioned in another thread I was the victim of vandals/thieves over the weekend and one of the t
|
||
Jack
at 11:28pm 08.09.06
11/10793
I have a solid green corrosion on all my seacocks. Why is this happening to ALL my seacocks elbows
|
||
mike c
at 11:21pm 08.09.06
2/2050
will be heading to the Cape in a week. Are there any sailing opportunities near Wellfleet that I ca
|
||
Alcohol Stove (1)
Craig16877
at 9:18pm 08.09.06
5/1373
We are new to sailing (1 year). Our 1985 Hunter 31 has an Alcohol Stove. Where can I get instructi
|
||
CHET P
at 4:05pm 08.09.06
4/975
WELL GUYS THIS FORUM HAS ALWAYS BEEN HELPFULL BEFORE AND I DON'T EXPECT ANY LESS NOW. THE WIFE AND I
|
||
Joseph Baker
at 2:59pm 08.09.06
2/1254
I need help in making an anchor locker for my 1980 33' Hunter Sloop. I purchased a manual windlass b
|
||
Rick
at 1:54pm 08.09.06
15/15704
I'm looking at an Island Packet 350 but am having a devil of a time finding reliable info on this bo
|
||
Jim G.
at 12:06pm 08.09.06
9/2723
I regularly read that bending the mast back will flatten the main sail but I have trouble visualisin
|
||
Eric14428
at 11:44am 08.09.06
6/1043
Bought my first boat January '06, selling said boat now for a few reasons none boat specific. My qu
|
||
Mark
at 11:43am 08.09.06
3/744
Looking for some help. Got caught in a hard wind no warning. 3 motor boats sank two sail boats went
|
||
Brad Hoff
at 11:10am 08.09.06
14/1871
I recently saw a fuel polisher type system that can be installed onboard. This unit was about $2,400
|
||
Chaos
at 10:41am 08.09.06
5/1701
I would like to get a few takes on my situation. I did OK in our Regattas the first year I have owne
|
||
elle
at 10:35am 08.09.06
0/755
Who is a good dealer for a sailboat trailer in the VA MD area?? Only want to spend $3000ish.Thanks
|
Replacement feathering prop
uncledom at 5:42am 01.11.21 I swear by my Brunton's Auto Prop. It is still the best upgrade I've made to my 2006 Hunter 41. I |
||
Mast Sail Slide Channel
rgranger at 5:26am 01.11.21 I bet you could fab one out of some heavy guage PVC square pipe. Schedule 80 would make a very nice |
||
Should I replace my old Yanmar motor mounts with OEMs or a newer design?
Justin_NSA at 5:20am 01.11.21 The reviews from customers sound favorable but I'm not sure what comparing old, worn out OEM mounts |
||
Engine alignment issue?
kloudie1 at 5:03am 01.11.21 Once back in the water, disconnect the coupling at the transmission and push the shaft aft about a q |
||
323 air conditioner
SycloneDriver at 4:46am 01.11.21 It gets unbearably hot and humid in the summer in Florida. In the Gulf of Mexico the winds die d |
||
cleaning sunbrella
nightowle at 4:00am 01.11.21 I used Woolite mixed with white vinegar on my light grey sunbrella. It works well for the green stu |
||
Should I replace my old Yanmar motor mounts with OEMs or a newer design?
sailme88 at 3:23am 01.11.21 Ok, let's see if I have the question correct: On the one hand I can save $200.00 and install the id |
||
Engine alignment issue?
Slipin Away at 1:42am 01.11.21 Shaft is normally offset so it can be removed without dropping the rudder |
||
Coaming Treads Teak C-30 Mk II
weekendrken at 11:30pm 01.10.21 I added step treads to my mk-1 and screwed them down. A #8 oval head screw near each corner, counter |
||
Should I replace my old Yanmar motor mounts with OEMs or a newer design?
ggrizzard at 11:05pm 01.10.21 I found these for $396 US: https://www.parts4engines.com/yanmar-2gm20-engine-mount If I read corre |
||
H26 Proposed Reef Configuration
CaptainRan at 10:07pm 01.10.21 Thanks everyone for your inputs.Not placing hardware on the side of the boom for safety was a good p |
||
Seatalk...whotalk..metalk...please talk? (1)
Team118 at 10:00pm 01.10.21 Thanks John. I get the SOG vs speed through water...didn't think about it that detailed! I did a qu |
||
Emergency Tiller (2)
Grizzly Sailor at 9:58pm 01.10.21 Here are a few pics for reference. The first is of my stem. The second is the E-tiller. Since ta |
||
AIS Receive Problem Identification
Rick D at 9:39pm 01.10.21 It seems to me over the last year or so many fewer commercial ships ( tankers and container ships) |